Hi all , I am trying to use an OMAP3430 (MUSB controller )based board as a USB mass storage device.I am using kernel 2.6.28 on the gadget side. Enumeration happens fine , the mass storage driver gets loaded and udev creates the /dev entry for the disk.But the disk(which is an MMC card plugged into the board) does not get mounted and after some time the gadget gets reset.A manual mount hangs.I have tested this with hosts running Linux 2.6.23, 2.6.26 , 2.6.29-rc3 and Windows.Please see some debug messages from host/gadget below.I have attached an usbmon o/p also. Thanks for your time, Regards, Silesh. ---------------------------------------------------------------------------------------------------------- dmesg: Feb 3 11:54:39 work kernel: [ 7074.518149] usb 1-5: new high speed USB device using ehci_hcd and address 16 Feb 3 11:54:39 work kernel: [ 7074.733090] usb 1-5: New USB device found, idVendor=0525, idProduct=a4a5 Feb 3 11:54:39 work kernel: [ 7074.733095] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Feb 3 11:54:39 work kernel: [ 7074.733098] usb 1-5: Product: File-backed Storage Gadget Feb 3 11:54:39 work kernel: [ 7074.733100] usb 1-5: Manufacturer: Linux 2.6.28-omap1-00232-g4f8edb9-dirty with musb_hdrc Feb 3 11:54:39 work kernel: [ 7074.733102] usb 1-5: SerialNumber: 372041756775 Feb 3 11:54:39 work kernel: [ 7074.733696] usb 1-5: configuration #1 chosen from 1 choice Feb 3 11:54:39 work kernel: [ 7074.779574] scsi10 : SCSI emulation for USB Mass Storage devices Feb 3 11:54:44 work kernel: [ 7079.823400] scsi 10:0:0:0: Direct-Access Linux File-Stor Gadget 0316 PQ: 0 ANSI: 2 Feb 3 11:54:44 work kernel: [ 7079.910104] sd 10:0:0:0: [sdb] 3967992 512-byte hardware sectors: (2.03 GB/1.89 GiB) Feb 3 11:54:44 work kernel: [ 7079.934103] sd 10:0:0:0: [sdb] Write Protect is off Feb 3 11:54:44 work kernel: [ 7079.934106] sd 10:0:0:0: [sdb] Assuming drive cache: write through Feb 3 11:54:44 work kernel: [ 7079.970396] sd 10:0:0:0: [sdb] 3967992 512-byte hardware sectors: (2.03 GB/1.89 GiB) Feb 3 11:54:44 work kernel: [ 7079.994353] sd 10:0:0:0: [sdb] Write Protect is off Feb 3 11:54:44 work kernel: [ 7079.994356] sd 10:0:0:0: [sdb] Assuming drive cache: write through Feb 3 11:54:44 work kernel: [ 7079.994360] sdb:<7>usb-storage: queuecommand called Feb 3 11:54:45 work kernel: [ 7080.012039] Feb 3 11:54:45 work kernel: [ 7080.013919] sd 10:0:0:0: [sdb] Attached SCSI disk Feb 3 11:54:45 work kernel: [ 7080.014001] sd 10:0:0:0: Attached scsi generic sg2 type 0 Feb 3 11:55:46 work kernel: [ 7141.099540] usb 1-5: reset high speed USB device using ehci_hcd and address 16 Feb 3 11:56:47 work kernel: [ 7202.099238] usb 1-5: reset high speed USB device using ehci_hcd and address 16 Feb 3 11:57:48 work kernel: [ 7263.099418] usb 1-5: reset high speed USB device using ehci_hcd and address 16 Feb 3 11:58:49 work kernel: [ 7324.099233] usb 1-5: reset high speed USB device using ehci_hcd and address 16 Feb 3 11:59:50 work kernel: [ 7385.105152] usb 1-5: reset high speed USB device using ehci_hcd and address 16 Feb 3 12:00:51 work kernel: [ 7446.099217] usb 1-5: reset high speed USB device using ehci_hcd and address 16 Feb 3 12:00:51 work kernel: [ 7446.362279] sd 10:0:0:0: [sdb] Unhandled error code Feb 3 12:00:51 work kernel: [ 7446.362282] sd 10:0:0:0: [sdb] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK Feb 3 12:00:51 work kernel: [ 7446.362288] end_request: I/O error, dev sdb, sector 3967984 Feb 3 12:00:51 work kernel: [ 7446.362293] Buffer I/O error on device sdb, logical block 495998 ------------------------------------------------------------------------------------- /proc/bus/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0525 ProdID=a4a5 Rev= 3.16 S: Manufacturer=Linux 2.6.28-omap1-00232-g4f8edb9-dirty with musb_hdrc S: Product=File-backed Storage Gadget S: SerialNumber=372041756775 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us ----------------------------------------------------------------------------------------------------- debug messages from gadget side: g_file_storage gadget: disconnect or port reset g_file_storage gadget: bulk-out, length 0: g_file_storage gadget: bulk_out_complete --> -104, 0/31 g_file_storage gadget: reset config g_file_storage gadget: reset interface g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: disconnect or port reset g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get configuration descriptor g_file_storage gadget: ep0-in, length 9: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get configuration descriptor g_file_storage gadget: ep0-in, length 35: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 4: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 54: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 110: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: set configuration g_file_storage gadget: set interface 0 g_file_storage gadget: high speed config #1 g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get max LUN g_file_storage gadget: ep0-in, length 1: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: INQUIRY; Dc=6, Di=36; Hc=6, Hi=36 g_file_storage gadget: bulk-in, length 36: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: sending command-failure status g_file_storage gadget: sense data: SK x06, ASC x29, ASCQ x00; info x0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: REQUEST SENSE; Dc=6, Di=18; Hc=6, Hi=18 g_file_storage gadget: bulk-in, length 18: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ CAPACITY; Dc=10, Di=8; Hc=10, Hi=8 g_file_storage gadget: bulk-in, length 8: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: MODE SENSE(6); Dc=6, Di=192; Hc=6, Hi=192 g_file_storage gadget: bulk-in, length 16: g_file_storage gadget: bulk-in set halt g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ CAPACITY; Dc=10, Di=8; Hc=10, Hi=8 g_file_storage gadget: bulk-in, length 8: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: MODE SENSE(6); Dc=6, Di=192; Hc=6, Hi=192 g_file_storage gadget: bulk-in, length 16: g_file_storage gadget: bulk-in set halt g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=4096; Hc=10, Hi=4096 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=4096; Hc=10, Hi=4096 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=4096; Hc=10, Hi=4096 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=4096; Hc=10, Hi=4096 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=16384; Hc=10, Hi=16384 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=512; Hc=10, Hi=512 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: disconnect or port reset g_file_storage gadget: bulk_in_complete --> -104, 0/13 g_file_storage gadget: bulk_in_complete --> -104, 0/512 g_file_storage gadget: reset config g_file_storage gadget: reset interface g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: disconnect or port reset g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get configuration descriptor g_file_storage gadget: ep0-in, length 35: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: set configuration g_file_storage gadget: set interface 0 g_file_storage gadget: high speed config #1 g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: bulk-out, length 0: g_file_storage gadget: bulk_out_complete --> -104, 0/31 g_file_storage gadget: reset interface g_file_storage gadget: set interface 0 g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: sending command-failure status g_file_storage gadget: sense data: SK x06, ASC x29, ASCQ x00; info x0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: REQUEST SENSE; Dc=6, Di=18; Hc=6, Hi=18 g_file_storage gadget: bulk-in, length 18: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=512; Hc=10, Hi=512 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: disconnect or port reset g_file_storage gadget: bulk_in_complete --> -104, 0/512 g_file_storage gadget: bulk_in_complete --> -104, 0/13 g_file_storage gadget: reset config g_file_storage gadget: reset interface g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: disconnect or port reset g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get configuration descriptor g_file_storage gadget: ep0-in, length 35: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: set configuration g_file_storage gadget: set interface 0 g_file_storage gadget: high speed config #1 g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: bulk-out, length 0: g_file_storage gadget: bulk_out_complete --> -104, 0/31 g_file_storage gadget: reset interface g_file_storage gadget: set interface 0 g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: sending command-failure status g_file_storage gadget: sense data: SK x06, ASC x29, ASCQ x00; info x0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: REQUEST SENSE; Dc=6, Di=18; Hc=6, Hi=18 g_file_storage gadget: bulk-in, length 18: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=512; Hc=10, Hi=512 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: disconnect or port reset g_file_storage gadget: bulk_in_complete --> -104, 0/512 g_file_storage gadget: bulk_in_complete --> -104, 0/13 g_file_storage gadget: reset config g_file_storage gadget: reset interface g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: disconnect or port reset g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get configuration descriptor g_file_storage gadget: ep0-in, length 35: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: set configuration g_file_storage gadget: set interface 0 g_file_storage gadget: high speed config #1 g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: bulk-out, length 0: g_file_storage gadget: bulk_out_complete --> -104, 0/31 g_file_storage gadget: reset interface g_file_storage gadget: set interface 0 g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: sending command-failure status g_file_storage gadget: sense data: SK x06, ASC x29, ASCQ x00; info x0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: REQUEST SENSE; Dc=6, Di=18; Hc=6, Hi=18 g_file_storage gadget: bulk-in, length 18: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=512; Hc=10, Hi=512 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: disconnect or port reset g_file_storage gadget: bulk_in_complete --> -104, 0/512 g_file_storage gadget: bulk_in_complete --> -104, 0/13 g_file_storage gadget: reset config g_file_storage gadget: reset interface g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: disconnect or port reset g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get configuration descriptor g_file_storage gadget: ep0-in, length 35: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: set configuration g_file_storage gadget: set interface 0 g_file_storage gadget: high speed config #1 g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: bulk-out, length 0: g_file_storage gadget: bulk_out_complete --> -104, 0/31 g_file_storage gadget: reset interface g_file_storage gadget: set interface 0 g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: sending command-failure status g_file_storage gadget: sense data: SK x06, ASC x29, ASCQ x00; info x0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: REQUEST SENSE; Dc=6, Di=18; Hc=6, Hi=18 g_file_storage gadget: bulk-in, length 18: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=512; Hc=10, Hi=512 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: disconnect or port reset g_file_storage gadget: bulk_in_complete --> -104, 0/512 g_file_storage gadget: bulk_in_complete --> -104, 0/13 g_file_storage gadget: reset config g_file_storage gadget: reset interface g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: disconnect or port reset g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get configuration descriptor g_file_storage gadget: ep0-in, length 35: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: set configuration g_file_storage gadget: set interface 0 g_file_storage gadget: high speed config #1 g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: bulk-out, length 0: g_file_storage gadget: bulk_out_complete --> -104, 0/31 g_file_storage gadget: reset interface g_file_storage gadget: set interface 0 g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: sending command-failure status g_file_storage gadget: sense data: SK x06, ASC x29, ASCQ x00; info x0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: REQUEST SENSE; Dc=6, Di=18; Hc=6, Hi=18 g_file_storage gadget: bulk-in, length 18: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: READ(10); Dc=10, Di=512; Hc=10, Hi=512 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: disconnect or port reset g_file_storage gadget: bulk_in_complete --> -104, 0/512 g_file_storage gadget: bulk_in_complete --> -104, 0/13 g_file_storage gadget: reset config g_file_storage gadget: reset interface g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: disconnect or port reset g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get device descriptor g_file_storage gadget: ep0-in, length 18: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get configuration descriptor g_file_storage gadget: ep0-in, length 35: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: get string descriptor g_file_storage gadget: ep0-in, length 26: g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: set configuration g_file_storage gadget: set interface 0 g_file_storage gadget: high speed config #1 g_file_storage gadget: ep0-setup, length 8: g_file_storage gadget: bulk-out, length 0: g_file_storage gadget: bulk_out_complete --> -104, 0/31 g_file_storage gadget: reset interface g_file_storage gadget: set interface 0 g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: sending command-failure status g_file_storage gadget: sense data: SK x06, ASC x29, ASCQ x00; info x0 g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: REQUEST SENSE; Dc=6, Di=18; Hc=6, Hi=18 g_file_storage gadget: bulk-in, length 18: g_file_storage gadget: bulk-in, length 13: g_file_storage gadget: bulk-out, length 31: g_file_storage gadget: SCSI command: TEST UNIT READY; Dc=6, Dn=0; Hc=6, Hn=0 g_file_storage gadget: bulk-in, length 13: .... ------------------------------------------------------------------------------------------------------------- debug messages from host side: [ 7074.518149] usb 1-5: new high speed USB device using ehci_hcd and address 16 [ 7074.581571] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7074.581577] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7074.684113] usb 1-5: skipped 1 descriptor after configuration [ 7074.696155] usb 1-5: default language 0x0409 [ 7074.733090] usb 1-5: New USB device found, idVendor=0525, idProduct=a4a5 [ 7074.733095] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7074.733098] usb 1-5: Product: File-backed Storage Gadget [ 7074.733100] usb 1-5: Manufacturer: Linux 2.6.28-omap1-00232-g4f8edb9-dirty with musb_hdrc [ 7074.733102] usb 1-5: SerialNumber: 372041756775 [ 7074.733674] usb 1-5: uevent [ 7074.733693] usb 1-5: usb_probe_device [ 7074.733696] usb 1-5: configuration #1 chosen from 1 choice [ 7074.763705] usb 1-5: adding 1-5:1.0 (config #1, interface 0) [ 7074.775930] usb 1-5:1.0: uevent [ 7074.775959] usb-storage 1-5:1.0: usb_probe_interface [ 7074.775961] usb-storage 1-5:1.0: usb_probe_interface - got id [ 7074.775964] usb-storage: USB Mass Storage device detected [ 7074.778279] usb-storage: -- associate_dev [ 7074.778283] usb-storage: Vendor: 0x0525, Product: 0xa4a5, Revision: 0x0316 [ 7074.778285] usb-storage: Interface Subclass: 0x06, Protocol: 0x50 [ 7074.778289] usb-storage: Transport: Bulk [ 7074.778290] usb-storage: Protocol: Transparent SCSI [ 7074.779574] scsi10 : SCSI emulation for USB Mass Storage devices [ 7074.780894] usb-storage: *** thread sleeping. [ 7074.781003] drivers/usb/core/inode.c: creating file '016' [ 7074.790978] usb-storage: device found at 16 [ 7074.790983] usb-storage: waiting for device to settle before scanning [ 7079.792406] usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1 [ 7079.803622] usb-storage: GetMaxLUN command result is 1, data is 0 [ 7079.803658] usb-storage: queuecommand called [ 7079.803663] usb-storage: *** thread awakened. [ 7079.803666] usb-storage: Command INQUIRY (6 bytes) [ 7079.803667] usb-storage: 12 00 00 00 24 00 [ 7079.803672] usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6 [ 7079.803674] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.803813] usb-storage: Status code 0; transferred 31/31 [ 7079.803814] usb-storage: -- transfer complete [ 7079.803816] usb-storage: Bulk command transfer result=0 [ 7079.803817] usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries [ 7079.819047] usb-storage: Status code 0; transferred 36/36 [ 7079.819051] usb-storage: -- transfer complete [ 7079.819053] usb-storage: Bulk data transfer result 0x0 [ 7079.819055] usb-storage: Attempting to get CSW... [ 7079.819057] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.823100] usb-storage: Status code 0; transferred 13/13 [ 7079.823103] usb-storage: -- transfer complete [ 7079.823105] usb-storage: Bulk status result = 0 [ 7079.823106] usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0 [ 7079.823109] usb-storage: scsi cmd done, result=0x0 [ 7079.823113] usb-storage: *** thread sleeping. [ 7079.823400] scsi 10:0:0:0: Direct-Access Linux File-Stor Gadget 0316 PQ: 0 ANSI: 2 [ 7079.823494] usb-storage: queuecommand called [ 7079.823498] usb-storage: *** thread awakened. [ 7079.823501] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7079.823502] usb-storage: 00 00 00 00 00 00 [ 7079.823507] usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7079.823509] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.823567] usb-storage: Status code 0; transferred 31/31 [ 7079.823569] usb-storage: -- transfer complete [ 7079.823570] usb-storage: Bulk command transfer result=0 [ 7079.823571] usb-storage: Attempting to get CSW... [ 7079.823573] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.854545] usb-storage: Status code 0; transferred 13/13 [ 7079.854549] usb-storage: -- transfer complete [ 7079.854551] usb-storage: Bulk status result = 0 [ 7079.854553] usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x1 [ 7079.854555] usb-storage: -- transport indicates command failure [ 7079.854556] usb-storage: Issuing auto-REQUEST_SENSE [ 7079.854560] usb-storage: Bulk Command S 0x43425355 T 0x3 L 18 F 128 Trg 0 LUN 0 CL 6 [ 7079.854562] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.854695] usb-storage: Status code 0; transferred 31/31 [ 7079.854696] usb-storage: -- transfer complete [ 7079.854698] usb-storage: Bulk command transfer result=0 [ 7079.854700] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 7079.870291] usb-storage: Status code 0; transferred 18/18 [ 7079.870295] usb-storage: -- transfer complete [ 7079.870297] usb-storage: Bulk data transfer result 0x0 [ 7079.870298] usb-storage: Attempting to get CSW... [ 7079.870300] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.874473] usb-storage: Status code 0; transferred 13/13 [ 7079.874476] usb-storage: -- transfer complete [ 7079.874477] usb-storage: Bulk status result = 0 [ 7079.874479] usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0 [ 7079.874482] usb-storage: -- Result from auto-sense is 0 [ 7079.874483] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 7079.874487] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 7079.874490] usb-storage: scsi cmd done, result=0x2 [ 7079.874494] usb-storage: *** thread sleeping. [ 7079.874521] usb-storage: queuecommand called [ 7079.874525] usb-storage: *** thread awakened. [ 7079.874526] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7079.874528] usb-storage: 00 00 00 00 00 00 [ 7079.874533] usb-storage: Bulk Command S 0x43425355 T 0x4 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7079.874535] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.874692] usb-storage: Status code 0; transferred 31/31 [ 7079.874694] usb-storage: -- transfer complete [ 7079.874695] usb-storage: Bulk command transfer result=0 [ 7079.874697] usb-storage: Attempting to get CSW... [ 7079.874698] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.890294] usb-storage: Status code 0; transferred 13/13 [ 7079.890298] usb-storage: -- transfer complete [ 7079.890300] usb-storage: Bulk status result = 0 [ 7079.890302] usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0 [ 7079.890305] usb-storage: scsi cmd done, result=0x0 [ 7079.890310] usb-storage: *** thread sleeping. [ 7079.890343] usb-storage: queuecommand called [ 7079.890347] usb-storage: *** thread awakened. [ 7079.890350] usb-storage: Command READ_CAPACITY (10 bytes) [ 7079.890351] usb-storage: 25 00 00 00 00 00 00 00 00 00 [ 7079.890357] usb-storage: Bulk Command S 0x43425355 T 0x5 L 8 F 128 Trg 0 LUN 0 CL 10 [ 7079.890360] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.890444] usb-storage: Status code 0; transferred 31/31 [ 7079.890446] usb-storage: -- transfer complete [ 7079.890447] usb-storage: Bulk command transfer result=0 [ 7079.890449] usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries [ 7079.906044] usb-storage: Status code 0; transferred 8/8 [ 7079.906048] usb-storage: -- transfer complete [ 7079.906050] usb-storage: Bulk data transfer result 0x0 [ 7079.906052] usb-storage: Attempting to get CSW... [ 7079.906053] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.910073] usb-storage: Status code 0; transferred 13/13 [ 7079.910075] usb-storage: -- transfer complete [ 7079.910076] usb-storage: Bulk status result = 0 [ 7079.910078] usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0 [ 7079.910081] usb-storage: scsi cmd done, result=0x0 [ 7079.910084] usb-storage: *** thread sleeping. [ 7079.910104] sd 10:0:0:0: [sdb] 3967992 512-byte hardware sectors: (2.03 GB/1.89 GiB) [ 7079.910116] usb-storage: queuecommand called [ 7079.910120] usb-storage: *** thread awakened. [ 7079.910122] usb-storage: Command MODE_SENSE (6 bytes) [ 7079.910124] usb-storage: 1a 00 3f 00 c0 00 [ 7079.910133] usb-storage: Bulk Command S 0x43425355 T 0x6 L 192 F 128 Trg 0 LUN 0 CL 6 [ 7079.910135] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.910677] usb-storage: Status code 0; transferred 31/31 [ 7079.910680] usb-storage: -- transfer complete [ 7079.910681] usb-storage: Bulk command transfer result=0 [ 7079.910683] usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries [ 7079.926134] usb-storage: Status code -121; transferred 16/192 [ 7079.926138] usb-storage: -- short read transfer [ 7079.926139] usb-storage: Bulk data transfer result 0x1 [ 7079.926141] usb-storage: Attempting to get CSW... [ 7079.926143] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.929827] usb-storage: Status code -32; transferred 0/13 [ 7079.929829] usb-storage: clearing endpoint halt for pipe 0xc0009080 [ 7079.929832] usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 [ 7079.933821] usb-storage: usb_stor_clear_halt: result = 0 [ 7079.933823] usb-storage: Attempting to get CSW (2nd try)... [ 7079.933824] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.934070] usb-storage: Status code 0; transferred 13/13 [ 7079.934072] usb-storage: -- transfer complete [ 7079.934073] usb-storage: Bulk status result = 0 [ 7079.934075] usb-storage: Bulk Status S 0x53425355 T 0x6 R 176 Stat 0x0 [ 7079.934078] usb-storage: scsi cmd done, result=0x0 [ 7079.934082] usb-storage: *** thread sleeping. [ 7079.934103] sd 10:0:0:0: [sdb] Write Protect is off [ 7079.934104] sd 10:0:0:0: [sdb] Mode Sense: 0f 00 00 00 [ 7079.934106] sd 10:0:0:0: [sdb] Assuming drive cache: write through [ 7079.934539] usb-storage: queuecommand called [ 7079.934544] usb-storage: *** thread awakened. [ 7079.934546] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7079.934547] usb-storage: 00 00 00 00 00 00 [ 7079.934552] usb-storage: Bulk Command S 0x43425355 T 0x7 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7079.934554] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.934689] usb-storage: Status code 0; transferred 31/31 [ 7079.934691] usb-storage: -- transfer complete [ 7079.934692] usb-storage: Bulk command transfer result=0 [ 7079.934694] usb-storage: Attempting to get CSW... [ 7079.934695] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.950302] usb-storage: Status code 0; transferred 13/13 [ 7079.950306] usb-storage: -- transfer complete [ 7079.950307] usb-storage: Bulk status result = 0 [ 7079.950309] usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x0 [ 7079.950312] usb-storage: scsi cmd done, result=0x0 [ 7079.950316] usb-storage: *** thread sleeping. [ 7079.950347] usb-storage: queuecommand called [ 7079.950352] usb-storage: *** thread awakened. [ 7079.950354] usb-storage: Command READ_CAPACITY (10 bytes) [ 7079.950355] usb-storage: 25 00 00 00 00 00 00 00 00 00 [ 7079.950362] usb-storage: Bulk Command S 0x43425355 T 0x8 L 8 F 128 Trg 0 LUN 0 CL 10 [ 7079.950364] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.950467] usb-storage: Status code 0; transferred 31/31 [ 7079.950469] usb-storage: -- transfer complete [ 7079.950470] usb-storage: Bulk command transfer result=0 [ 7079.950472] usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries [ 7079.966180] usb-storage: Status code 0; transferred 8/8 [ 7079.966184] usb-storage: -- transfer complete [ 7079.966186] usb-storage: Bulk data transfer result 0x0 [ 7079.966187] usb-storage: Attempting to get CSW... [ 7079.966189] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.970356] usb-storage: Status code 0; transferred 13/13 [ 7079.970359] usb-storage: -- transfer complete [ 7079.970361] usb-storage: Bulk status result = 0 [ 7079.970363] usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x0 [ 7079.970366] usb-storage: scsi cmd done, result=0x0 [ 7079.970370] usb-storage: *** thread sleeping. [ 7079.970396] sd 10:0:0:0: [sdb] 3967992 512-byte hardware sectors: (2.03 GB/1.89 GiB) [ 7079.970414] usb-storage: queuecommand called [ 7079.970419] usb-storage: *** thread awakened. [ 7079.970421] usb-storage: Command MODE_SENSE (6 bytes) [ 7079.970422] usb-storage: 1a 00 3f 00 c0 00 [ 7079.970427] usb-storage: Bulk Command S 0x43425355 T 0x9 L 192 F 128 Trg 0 LUN 0 CL 6 [ 7079.970429] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.970566] usb-storage: Status code 0; transferred 31/31 [ 7079.970568] usb-storage: -- transfer complete [ 7079.970569] usb-storage: Bulk command transfer result=0 [ 7079.970571] usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries [ 7079.986238] usb-storage: Status code -121; transferred 16/192 [ 7079.986242] usb-storage: -- short read transfer [ 7079.986244] usb-storage: Bulk data transfer result 0x1 [ 7079.986245] usb-storage: Attempting to get CSW... [ 7079.986247] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.989938] usb-storage: Status code -32; transferred 0/13 [ 7079.989940] usb-storage: clearing endpoint halt for pipe 0xc0009080 [ 7079.989942] usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 [ 7079.994028] usb-storage: usb_stor_clear_halt: result = 0 [ 7079.994033] usb-storage: Attempting to get CSW (2nd try)... [ 7079.994035] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7079.994321] usb-storage: Status code 0; transferred 13/13 [ 7079.994323] usb-storage: -- transfer complete [ 7079.994324] usb-storage: Bulk status result = 0 [ 7079.994326] usb-storage: Bulk Status S 0x53425355 T 0x9 R 176 Stat 0x0 [ 7079.994329] usb-storage: scsi cmd done, result=0x0 [ 7079.994333] usb-storage: *** thread sleeping. [ 7079.994353] sd 10:0:0:0: [sdb] Write Protect is off [ 7079.994355] sd 10:0:0:0: [sdb] Mode Sense: 0f 00 00 00 [ 7079.994356] sd 10:0:0:0: [sdb] Assuming drive cache: write through [ 7079.994360] sdb:<7>usb-storage: queuecommand called [ 7079.994385] usb-storage: *** thread awakened. [ 7079.994387] usb-storage: Command READ_10 (10 bytes) [ 7079.994389] usb-storage: 28 00 00 00 00 00 00 00 08 00 [ 7079.994395] usb-storage: Bulk Command S 0x43425355 T 0xa L 4096 F 128 Trg 0 LUN 0 CL 10 [ 7079.994397] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7079.994571] usb-storage: Status code 0; transferred 31/31 [ 7079.994573] usb-storage: -- transfer complete [ 7079.994574] usb-storage: Bulk command transfer result=0 [ 7079.994576] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 7080.007157] usb-storage: Status code 0; transferred 4096/4096 [ 7080.007163] usb-storage: -- transfer complete [ 7080.007165] usb-storage: Bulk data transfer result 0x0 [ 7080.007166] usb-storage: Attempting to get CSW... [ 7080.007168] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7080.011995] usb-storage: Status code 0; transferred 13/13 [ 7080.011999] usb-storage: -- transfer complete [ 7080.012000] usb-storage: Bulk status result = 0 [ 7080.012002] usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0 [ 7080.012005] usb-storage: scsi cmd done, result=0x0 [ 7080.012009] usb-storage: *** thread sleeping. [ 7080.012039] [ 7080.013919] sd 10:0:0:0: [sdb] Attached SCSI disk [ 7080.014001] sd 10:0:0:0: Attached scsi generic sg2 type 0 [ 7080.014052] usb-storage: queuecommand called [ 7080.014058] usb-storage: *** thread awakened. [ 7080.014059] usb-storage: Bad target number (1:0) [ 7080.014061] usb-storage: scsi cmd done, result=0x40000 [ 7080.014064] usb-storage: *** thread sleeping. [ 7080.014090] usb-storage: queuecommand called [ 7080.014094] usb-storage: *** thread awakened. [ 7080.014095] usb-storage: Bad target number (2:0) [ 7080.014097] usb-storage: scsi cmd done, result=0x40000 [ 7080.014099] usb-storage: *** thread sleeping. [ 7080.014118] usb-storage: queuecommand called [ 7080.014122] usb-storage: *** thread awakened. [ 7080.014123] usb-storage: Bad target number (3:0) [ 7080.014124] usb-storage: scsi cmd done, result=0x40000 [ 7080.014136] usb-storage: *** thread sleeping. [ 7080.019282] usb-storage: queuecommand called [ 7080.019290] usb-storage: *** thread awakened. [ 7080.019291] usb-storage: Bad target number (4:0) [ 7080.019293] usb-storage: scsi cmd done, result=0x40000 [ 7080.019296] usb-storage: *** thread sleeping. [ 7080.019319] usb-storage: queuecommand called [ 7080.019323] usb-storage: *** thread awakened. [ 7080.019324] usb-storage: Bad target number (5:0) [ 7080.019326] usb-storage: scsi cmd done, result=0x40000 [ 7080.019328] usb-storage: *** thread sleeping. [ 7080.019347] usb-storage: queuecommand called [ 7080.019350] usb-storage: *** thread awakened. [ 7080.019352] usb-storage: Bad target number (6:0) [ 7080.019353] usb-storage: scsi cmd done, result=0x40000 [ 7080.019355] usb-storage: *** thread sleeping. [ 7080.019374] usb-storage: queuecommand called [ 7080.019377] usb-storage: *** thread awakened. [ 7080.019379] usb-storage: Bad target number (7:0) [ 7080.019380] usb-storage: scsi cmd done, result=0x40000 [ 7080.019382] usb-storage: *** thread sleeping. [ 7080.019391] usb-storage: device scan complete [ 7080.051215] usb-storage: queuecommand called [ 7080.051223] usb-storage: *** thread awakened. [ 7080.051227] usb-storage: Command READ_10 (10 bytes) [ 7080.051228] usb-storage: 28 00 00 3c 8b 00 00 00 08 00 [ 7080.051236] usb-storage: Bulk Command S 0x43425355 T 0xb L 4096 F 128 Trg 0 LUN 0 CL 10 [ 7080.051238] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7080.051443] usb-storage: Status code 0; transferred 31/31 [ 7080.051445] usb-storage: -- transfer complete [ 7080.051447] usb-storage: Bulk command transfer result=0 [ 7080.051449] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 7080.063288] usb-storage: Status code 0; transferred 4096/4096 [ 7080.063291] usb-storage: -- transfer complete [ 7080.063293] usb-storage: Bulk data transfer result 0x0 [ 7080.063295] usb-storage: Attempting to get CSW... [ 7080.063296] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7080.067231] usb-storage: Status code 0; transferred 13/13 [ 7080.067235] usb-storage: -- transfer complete [ 7080.067237] usb-storage: Bulk status result = 0 [ 7080.067238] usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x0 [ 7080.067242] usb-storage: scsi cmd done, result=0x0 [ 7080.067246] usb-storage: *** thread sleeping. [ 7080.067307] usb-storage: queuecommand called [ 7080.067312] usb-storage: *** thread awakened. [ 7080.067315] usb-storage: Command READ_10 (10 bytes) [ 7080.067316] usb-storage: 28 00 00 3c 8b e8 00 00 08 00 [ 7080.067323] usb-storage: Bulk Command S 0x43425355 T 0xc L 4096 F 128 Trg 0 LUN 0 CL 10 [ 7080.067325] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7080.067486] usb-storage: Status code 0; transferred 31/31 [ 7080.067488] usb-storage: -- transfer complete [ 7080.067490] usb-storage: Bulk command transfer result=0 [ 7080.067491] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 7080.079505] usb-storage: Status code 0; transferred 4096/4096 [ 7080.079509] usb-storage: -- transfer complete [ 7080.079511] usb-storage: Bulk data transfer result 0x0 [ 7080.079513] usb-storage: Attempting to get CSW... [ 7080.079515] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7080.083369] usb-storage: Status code 0; transferred 13/13 [ 7080.083373] usb-storage: -- transfer complete [ 7080.083375] usb-storage: Bulk status result = 0 [ 7080.083377] usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0 [ 7080.083380] usb-storage: scsi cmd done, result=0x0 [ 7080.083384] usb-storage: *** thread sleeping. [ 7080.084178] usb-storage: queuecommand called [ 7080.084447] usb-storage: *** thread awakened. [ 7080.084450] usb-storage: Command READ_10 (10 bytes) [ 7080.084452] usb-storage: 28 00 00 00 00 00 00 00 08 00 [ 7080.084458] usb-storage: Bulk Command S 0x43425355 T 0xd L 4096 F 128 Trg 0 LUN 0 CL 10 [ 7080.084461] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7080.084571] usb-storage: Status code 0; transferred 31/31 [ 7080.084572] usb-storage: -- transfer complete [ 7080.084574] usb-storage: Bulk command transfer result=0 [ 7080.084575] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 7080.096586] usb-storage: Status code 0; transferred 4096/4096 [ 7080.096589] usb-storage: -- transfer complete [ 7080.096591] usb-storage: Bulk data transfer result 0x0 [ 7080.096593] usb-storage: Attempting to get CSW... [ 7080.096595] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7080.100702] usb-storage: Status code 0; transferred 13/13 [ 7080.100704] usb-storage: -- transfer complete [ 7080.100706] usb-storage: Bulk status result = 0 [ 7080.100708] usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x0 [ 7080.100710] usb-storage: scsi cmd done, result=0x0 [ 7080.100714] usb-storage: *** thread sleeping. [ 7080.100766] usb-storage: queuecommand called [ 7080.100771] usb-storage: *** thread awakened. [ 7080.100774] usb-storage: Command READ_10 (10 bytes) [ 7080.100775] usb-storage: 28 00 00 00 00 08 00 00 20 00 [ 7080.100782] usb-storage: Bulk Command S 0x43425355 T 0xe L 16384 F 128 Trg 0 LUN 0 CL 10 [ 7080.100784] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7080.100949] usb-storage: Status code 0; transferred 31/31 [ 7080.100950] usb-storage: -- transfer complete [ 7080.100952] usb-storage: Bulk command transfer result=0 [ 7080.100953] usb-storage: usb_stor_bulk_transfer_sglist: xfer 16384 bytes, 4 entries [ 7080.113495] usb-storage: Status code 0; transferred 16384/16384 [ 7080.113499] usb-storage: -- transfer complete [ 7080.113501] usb-storage: Bulk data transfer result 0x0 [ 7080.113502] usb-storage: Attempting to get CSW... [ 7080.113504] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7080.117078] usb-storage: Status code 0; transferred 13/13 [ 7080.117080] usb-storage: -- transfer complete [ 7080.117081] usb-storage: Bulk status result = 0 [ 7080.117083] usb-storage: Bulk Status S 0x53425355 T 0xe R 0 Stat 0x0 [ 7080.117085] usb-storage: scsi cmd done, result=0x0 [ 7080.117089] usb-storage: *** thread sleeping. [ 7080.117153] usb-storage: queuecommand called [ 7080.117351] usb-storage: *** thread awakened. [ 7080.117354] usb-storage: Command READ_10 (10 bytes) [ 7080.117355] usb-storage: 28 00 00 3c 8b f0 00 00 01 00 [ 7080.117361] usb-storage: Bulk Command S 0x43425355 T 0xf L 512 F 128 Trg 0 LUN 0 CL 10 [ 7080.117363] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7080.117443] usb-storage: Status code 0; transferred 31/31 [ 7080.117445] usb-storage: -- transfer complete [ 7080.117446] usb-storage: Bulk command transfer result=0 [ 7080.117448] usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries [ 7140.997145] usb-storage: command_abort called [ 7140.997150] usb-storage: usb_stor_stop_transport called [ 7140.997152] usb-storage: -- cancelling sg request [ 7140.997399] usb-storage: Status code -104; transferred 0/512 [ 7140.997401] usb-storage: -- transfer cancelled [ 7140.997403] usb-storage: Bulk data transfer result 0x4 [ 7140.997405] usb-storage: -- command was aborted [ 7140.997409] usb-storage: storage_pre_reset [ 7141.048486] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7141.048492] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7141.099540] usb 1-5: reset high speed USB device using ehci_hcd and address 16 [ 7141.162490] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7141.162497] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7141.308279] usb-storage: storage_post_reset [ 7141.308286] usb-storage: usb_reset_device returns 0 [ 7141.308289] usb-storage: scsi command aborted [ 7141.308292] usb-storage: *** thread sleeping. [ 7141.308297] usb-storage: queuecommand called [ 7141.308301] usb-storage: *** thread awakened. [ 7141.308303] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7141.308305] usb-storage: 00 00 00 00 00 00 [ 7141.308310] usb-storage: Bulk Command S 0x43425355 T 0x10 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7141.308313] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7141.308388] usb-storage: Status code 0; transferred 31/31 [ 7141.308390] usb-storage: -- transfer complete [ 7141.308391] usb-storage: Bulk command transfer result=0 [ 7141.308392] usb-storage: Attempting to get CSW... [ 7141.308394] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7141.339041] usb-storage: Status code 0; transferred 13/13 [ 7141.339045] usb-storage: -- transfer complete [ 7141.339047] usb-storage: Bulk status result = 0 [ 7141.339048] usb-storage: Bulk Status S 0x53425355 T 0x10 R 0 Stat 0x1 [ 7141.339051] usb-storage: -- transport indicates command failure [ 7141.339052] usb-storage: Issuing auto-REQUEST_SENSE [ 7141.339056] usb-storage: Bulk Command S 0x43425355 T 0x11 L 18 F 128 Trg 0 LUN 0 CL 6 [ 7141.339058] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7141.339489] usb-storage: Status code 0; transferred 31/31 [ 7141.339492] usb-storage: -- transfer complete [ 7141.339493] usb-storage: Bulk command transfer result=0 [ 7141.339495] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 7141.354745] usb-storage: Status code 0; transferred 18/18 [ 7141.354749] usb-storage: -- transfer complete [ 7141.354751] usb-storage: Bulk data transfer result 0x0 [ 7141.354752] usb-storage: Attempting to get CSW... [ 7141.354754] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7141.358920] usb-storage: Status code 0; transferred 13/13 [ 7141.358923] usb-storage: -- transfer complete [ 7141.358925] usb-storage: Bulk status result = 0 [ 7141.358927] usb-storage: Bulk Status S 0x53425355 T 0x11 R 0 Stat 0x0 [ 7141.358929] usb-storage: -- Result from auto-sense is 0 [ 7141.358931] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 7141.358934] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 7141.358938] usb-storage: scsi cmd done, result=0x2 [ 7141.358942] usb-storage: *** thread sleeping. [ 7141.358947] usb-storage: queuecommand called [ 7141.358950] usb-storage: *** thread awakened. [ 7141.358952] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7141.358953] usb-storage: 00 00 00 00 00 00 [ 7141.358959] usb-storage: Bulk Command S 0x43425355 T 0x12 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7141.358961] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7141.361005] usb-storage: Status code 0; transferred 31/31 [ 7141.361008] usb-storage: -- transfer complete [ 7141.361010] usb-storage: Bulk command transfer result=0 [ 7141.361011] usb-storage: Attempting to get CSW... [ 7141.361013] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7141.374758] usb-storage: Status code 0; transferred 13/13 [ 7141.374762] usb-storage: -- transfer complete [ 7141.374763] usb-storage: Bulk status result = 0 [ 7141.374765] usb-storage: Bulk Status S 0x53425355 T 0x12 R 0 Stat 0x0 [ 7141.374768] usb-storage: scsi cmd done, result=0x0 [ 7141.374772] usb-storage: *** thread sleeping. [ 7141.374788] usb-storage: queuecommand called [ 7141.374792] usb-storage: *** thread awakened. [ 7141.374794] usb-storage: Command READ_10 (10 bytes) [ 7141.374795] usb-storage: 28 00 00 3c 8b f0 00 00 01 00 [ 7141.374802] usb-storage: Bulk Command S 0x43425355 T 0x13 L 512 F 128 Trg 0 LUN 0 CL 10 [ 7141.374804] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7141.374887] usb-storage: Status code 0; transferred 31/31 [ 7141.374888] usb-storage: -- transfer complete [ 7141.374890] usb-storage: Bulk command transfer result=0 [ 7141.374892] usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries [ 7201.997139] usb-storage: command_abort called [ 7201.997144] usb-storage: usb_stor_stop_transport called [ 7201.997146] usb-storage: -- cancelling sg request [ 7201.997356] usb-storage: Status code -104; transferred 0/512 [ 7201.997358] usb-storage: -- transfer cancelled [ 7201.997359] usb-storage: Bulk data transfer result 0x4 [ 7201.997361] usb-storage: -- command was aborted [ 7201.997365] usb-storage: storage_pre_reset [ 7202.048422] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7202.048428] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7202.099238] usb 1-5: reset high speed USB device using ehci_hcd and address 16 [ 7202.162425] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7202.162434] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7202.298870] usb-storage: storage_post_reset [ 7202.298879] usb-storage: usb_reset_device returns 0 [ 7202.298883] usb-storage: scsi command aborted [ 7202.298888] usb-storage: *** thread sleeping. [ 7202.298896] usb-storage: queuecommand called [ 7202.298903] usb-storage: *** thread awakened. [ 7202.298906] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7202.298909] usb-storage: 00 00 00 00 00 00 [ 7202.298919] usb-storage: Bulk Command S 0x43425355 T 0x14 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7202.298923] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7202.299084] usb-storage: Status code 0; transferred 31/31 [ 7202.299087] usb-storage: -- transfer complete [ 7202.299090] usb-storage: Bulk command transfer result=0 [ 7202.299093] usb-storage: Attempting to get CSW... [ 7202.299096] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7202.326150] usb-storage: Status code 0; transferred 13/13 [ 7202.326155] usb-storage: -- transfer complete [ 7202.326158] usb-storage: Bulk status result = 0 [ 7202.326162] usb-storage: Bulk Status S 0x53425355 T 0x14 R 0 Stat 0x1 [ 7202.326165] usb-storage: -- transport indicates command failure [ 7202.326168] usb-storage: Issuing auto-REQUEST_SENSE [ 7202.326174] usb-storage: Bulk Command S 0x43425355 T 0x15 L 18 F 128 Trg 0 LUN 0 CL 6 [ 7202.326178] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7202.326332] usb-storage: Status code 0; transferred 31/31 [ 7202.326335] usb-storage: -- transfer complete [ 7202.326338] usb-storage: Bulk command transfer result=0 [ 7202.326341] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 7202.342023] usb-storage: Status code 0; transferred 18/18 [ 7202.342028] usb-storage: -- transfer complete [ 7202.342032] usb-storage: Bulk data transfer result 0x0 [ 7202.342034] usb-storage: Attempting to get CSW... [ 7202.342038] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7202.345972] usb-storage: Status code 0; transferred 13/13 [ 7202.345976] usb-storage: -- transfer complete [ 7202.345979] usb-storage: Bulk status result = 0 [ 7202.345982] usb-storage: Bulk Status S 0x53425355 T 0x15 R 0 Stat 0x0 [ 7202.345986] usb-storage: -- Result from auto-sense is 0 [ 7202.345990] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 7202.345995] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 7202.346001] usb-storage: scsi cmd done, result=0x2 [ 7202.346007] usb-storage: *** thread sleeping. [ 7202.346015] usb-storage: queuecommand called [ 7202.346021] usb-storage: *** thread awakened. [ 7202.346025] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7202.346028] usb-storage: 00 00 00 00 00 00 [ 7202.346037] usb-storage: Bulk Command S 0x43425355 T 0x16 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7202.346041] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7202.347089] usb-storage: Status code 0; transferred 31/31 [ 7202.347092] usb-storage: -- transfer complete [ 7202.347095] usb-storage: Bulk command transfer result=0 [ 7202.347098] usb-storage: Attempting to get CSW... [ 7202.347101] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7202.361876] usb-storage: Status code 0; transferred 13/13 [ 7202.361881] usb-storage: -- transfer complete [ 7202.361884] usb-storage: Bulk status result = 0 [ 7202.361888] usb-storage: Bulk Status S 0x53425355 T 0x16 R 0 Stat 0x0 [ 7202.361892] usb-storage: scsi cmd done, result=0x0 [ 7202.361898] usb-storage: *** thread sleeping. [ 7202.361919] usb-storage: queuecommand called [ 7202.361926] usb-storage: *** thread awakened. [ 7202.361930] usb-storage: Command READ_10 (10 bytes) [ 7202.361933] usb-storage: 28 00 00 3c 8b f0 00 00 01 00 [ 7202.361945] usb-storage: Bulk Command S 0x43425355 T 0x17 L 512 F 128 Trg 0 LUN 0 CL 10 [ 7202.361950] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7202.362939] usb-storage: Status code 0; transferred 31/31 [ 7202.362943] usb-storage: -- transfer complete [ 7202.362946] usb-storage: Bulk command transfer result=0 [ 7202.362950] usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries [ 7202.361950] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7202.362939] usb-storage: Status code 0; transferred 31/31 [ 7202.362943] usb-storage: -- transfer complete [ 7202.362946] usb-storage: Bulk command transfer result=0 [ 7202.362950] usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries [ 7262.997144] usb-storage: command_abort called [ 7262.997149] usb-storage: usb_stor_stop_transport called [ 7262.997151] usb-storage: -- cancelling sg request [ 7262.997476] usb-storage: Status code -104; transferred 0/512 [ 7262.997478] usb-storage: -- transfer cancelled [ 7262.997480] usb-storage: Bulk data transfer result 0x4 [ 7262.997481] usb-storage: -- command was aborted [ 7262.997486] usb-storage: storage_pre_reset [ 7263.048607] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7263.048614] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7263.099418] usb 1-5: reset high speed USB device using ehci_hcd and address 16 [ 7263.162486] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7263.162492] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7263.299236] usb-storage: storage_post_reset [ 7263.299244] usb-storage: usb_reset_device returns 0 [ 7263.299248] usb-storage: scsi command aborted [ 7263.299254] usb-storage: *** thread sleeping. [ 7263.299261] usb-storage: queuecommand called [ 7263.299267] usb-storage: *** thread awakened. [ 7263.299271] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7263.299274] usb-storage: 00 00 00 00 00 00 [ 7263.299284] usb-storage: Bulk Command S 0x43425355 T 0x18 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7263.299288] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7263.299392] usb-storage: Status code 0; transferred 31/31 [ 7263.299395] usb-storage: -- transfer complete [ 7263.299398] usb-storage: Bulk command transfer result=0 [ 7263.299401] usb-storage: Attempting to get CSW... [ 7263.299404] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7263.329374] usb-storage: Status code 0; transferred 13/13 [ 7263.329378] usb-storage: -- transfer complete [ 7263.329380] usb-storage: Bulk status result = 0 [ 7263.329382] usb-storage: Bulk Status S 0x53425355 T 0x18 R 0 Stat 0x1 [ 7263.329384] usb-storage: -- transport indicates command failure [ 7263.329385] usb-storage: Issuing auto-REQUEST_SENSE [ 7263.329389] usb-storage: Bulk Command S 0x43425355 T 0x19 L 18 F 128 Trg 0 LUN 0 CL 6 [ 7263.329391] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7263.329508] usb-storage: Status code 0; transferred 31/31 [ 7263.329510] usb-storage: -- transfer complete [ 7263.329511] usb-storage: Bulk command transfer result=0 [ 7263.329513] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 7263.345148] usb-storage: Status code 0; transferred 18/18 [ 7263.345152] usb-storage: -- transfer complete [ 7263.345154] usb-storage: Bulk data transfer result 0x0 [ 7263.345155] usb-storage: Attempting to get CSW... [ 7263.345157] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7263.349397] usb-storage: Status code 0; transferred 13/13 [ 7263.349399] usb-storage: -- transfer complete [ 7263.349401] usb-storage: Bulk status result = 0 [ 7263.349402] usb-storage: Bulk Status S 0x53425355 T 0x19 R 0 Stat 0x0 [ 7263.349405] usb-storage: -- Result from auto-sense is 0 [ 7263.349407] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 7263.349410] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 7263.349413] usb-storage: scsi cmd done, result=0x2 [ 7263.349416] usb-storage: *** thread sleeping. [ 7263.349422] usb-storage: queuecommand called [ 7263.349425] usb-storage: *** thread awakened. [ 7263.349427] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7263.349428] usb-storage: 00 00 00 00 00 00 [ 7263.349433] usb-storage: Bulk Command S 0x43425355 T 0x1a L 0 F 0 Trg 0 LUN 0 CL 6 [ 7263.349435] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7263.349503] usb-storage: Status code 0; transferred 31/31 [ 7263.349505] usb-storage: -- transfer complete [ 7263.349506] usb-storage: Bulk command transfer result=0 [ 7263.349508] usb-storage: Attempting to get CSW... [ 7263.349509] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7263.365304] usb-storage: Status code 0; transferred 13/13 [ 7263.365309] usb-storage: -- transfer complete [ 7263.365312] usb-storage: Bulk status result = 0 [ 7263.365315] usb-storage: Bulk Status S 0x53425355 T 0x1a R 0 Stat 0x0 [ 7263.365320] usb-storage: scsi cmd done, result=0x0 [ 7263.365326] usb-storage: *** thread sleeping. [ 7263.365346] usb-storage: queuecommand called [ 7263.365353] usb-storage: *** thread awakened. [ 7263.365357] usb-storage: Command READ_10 (10 bytes) [ 7263.365360] usb-storage: 28 00 00 3c 8b f0 00 00 01 00 [ 7263.365372] usb-storage: Bulk Command S 0x43425355 T 0x1b L 512 F 128 Trg 0 LUN 0 CL 10 [ 7263.365377] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7263.365519] usb-storage: Status code 0; transferred 31/31 [ 7263.365522] usb-storage: -- transfer complete [ 7263.365525] usb-storage: Bulk command transfer result=0 [ 7263.365528] usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries [ 7323.997020] usb-storage: command_abort called [ 7323.997027] usb-storage: usb_stor_stop_transport called [ 7323.997030] usb-storage: -- cancelling sg request [ 7323.997504] usb-storage: Status code -104; transferred 0/512 [ 7323.997508] usb-storage: -- transfer cancelled [ 7323.997512] usb-storage: Bulk data transfer result 0x4 [ 7323.997514] usb-storage: -- command was aborted [ 7323.997521] usb-storage: storage_pre_reset [ 7324.048295] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7324.048304] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7324.099233] usb 1-5: reset high speed USB device using ehci_hcd and address 16 [ 7324.162421] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7324.162430] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7324.298641] usb-storage: storage_post_reset [ 7324.298649] usb-storage: usb_reset_device returns 0 [ 7324.298654] usb-storage: scsi command aborted [ 7324.298659] usb-storage: *** thread sleeping. [ 7324.298667] usb-storage: queuecommand called [ 7324.298673] usb-storage: *** thread awakened. [ 7324.298677] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7324.298679] usb-storage: 00 00 00 00 00 00 [ 7324.298689] usb-storage: Bulk Command S 0x43425355 T 0x1c L 0 F 0 Trg 0 LUN 0 CL 6 [ 7324.298694] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7324.298827] usb-storage: Status code 0; transferred 31/31 [ 7324.298830] usb-storage: -- transfer complete [ 7324.298833] usb-storage: Bulk command transfer result=0 [ 7324.298836] usb-storage: Attempting to get CSW... [ 7324.298839] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7324.325864] usb-storage: Status code 0; transferred 13/13 [ 7324.325869] usb-storage: -- transfer complete [ 7324.325872] usb-storage: Bulk status result = 0 [ 7324.325876] usb-storage: Bulk Status S 0x53425355 T 0x1c R 0 Stat 0x1 [ 7324.325879] usb-storage: -- transport indicates command failure [ 7324.325882] usb-storage: Issuing auto-REQUEST_SENSE [ 7324.325888] usb-storage: Bulk Command S 0x43425355 T 0x1d L 18 F 128 Trg 0 LUN 0 CL 6 [ 7324.325893] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7324.326124] usb-storage: Status code 0; transferred 31/31 [ 7324.326137] usb-storage: -- transfer complete [ 7324.326141] usb-storage: Bulk command transfer result=0 [ 7324.326144] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 7324.341747] usb-storage: Status code 0; transferred 18/18 [ 7324.341757] usb-storage: -- transfer complete [ 7324.341760] usb-storage: Bulk data transfer result 0x0 [ 7324.341763] usb-storage: Attempting to get CSW... [ 7324.341767] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7324.345722] usb-storage: Status code 0; transferred 13/13 [ 7324.345726] usb-storage: -- transfer complete [ 7324.345729] usb-storage: Bulk status result = 0 [ 7324.345733] usb-storage: Bulk Status S 0x53425355 T 0x1d R 0 Stat 0x0 [ 7324.345737] usb-storage: -- Result from auto-sense is 0 [ 7324.345740] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 7324.345745] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 7324.345751] usb-storage: scsi cmd done, result=0x2 [ 7324.345757] usb-storage: *** thread sleeping. [ 7324.345766] usb-storage: queuecommand called [ 7324.345772] usb-storage: *** thread awakened. [ 7324.345775] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7324.345778] usb-storage: 00 00 00 00 00 00 [ 7324.345788] usb-storage: Bulk Command S 0x43425355 T 0x1e L 0 F 0 Trg 0 LUN 0 CL 6 [ 7324.345792] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7324.345951] usb-storage: Status code 0; transferred 31/31 [ 7324.345955] usb-storage: -- transfer complete [ 7324.345957] usb-storage: Bulk command transfer result=0 [ 7324.345960] usb-storage: Attempting to get CSW... [ 7324.345963] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7324.361508] usb-storage: Status code 0; transferred 13/13 [ 7324.361514] usb-storage: -- transfer complete [ 7324.361517] usb-storage: Bulk status result = 0 [ 7324.361521] usb-storage: Bulk Status S 0x53425355 T 0x1e R 0 Stat 0x0 [ 7324.361525] usb-storage: scsi cmd done, result=0x0 [ 7324.361531] usb-storage: *** thread sleeping. [ 7324.361553] usb-storage: queuecommand called [ 7324.361561] usb-storage: *** thread awakened. [ 7324.361565] usb-storage: Command READ_10 (10 bytes) [ 7324.361567] usb-storage: 28 00 00 3c 8b f0 00 00 01 00 [ 7324.361580] usb-storage: Bulk Command S 0x43425355 T 0x1f L 512 F 128 Trg 0 LUN 0 CL 10 [ 7324.361585] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7324.361702] usb-storage: Status code 0; transferred 31/31 [ 7324.361705] usb-storage: -- transfer complete [ 7324.361708] usb-storage: Bulk command transfer result=0 [ 7324.361712] usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries [ 7384.997154] usb-storage: command_abort called [ 7384.997159] usb-storage: usb_stor_stop_transport called [ 7384.997161] usb-storage: -- cancelling sg request [ 7384.998321] usb-storage: Status code -104; transferred 0/512 [ 7384.998323] usb-storage: -- transfer cancelled [ 7384.998325] usb-storage: Bulk data transfer result 0x4 [ 7384.998326] usb-storage: -- command was aborted [ 7384.998330] usb-storage: storage_pre_reset [ 7385.049480] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7385.049488] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7385.105152] usb 1-5: reset high speed USB device using ehci_hcd and address 16 [ 7385.168607] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7385.168613] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7385.305630] usb-storage: storage_post_reset [ 7385.305636] usb-storage: usb_reset_device returns 0 [ 7385.305638] usb-storage: scsi command aborted [ 7385.305642] usb-storage: *** thread sleeping. [ 7385.305647] usb-storage: queuecommand called [ 7385.305650] usb-storage: *** thread awakened. [ 7385.305652] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7385.305653] usb-storage: 00 00 00 00 00 00 [ 7385.305658] usb-storage: Bulk Command S 0x43425355 T 0x20 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7385.305661] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7385.305750] usb-storage: Status code 0; transferred 31/31 [ 7385.305752] usb-storage: -- transfer complete [ 7385.305753] usb-storage: Bulk command transfer result=0 [ 7385.305755] usb-storage: Attempting to get CSW... [ 7385.305756] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7385.332945] usb-storage: Status code 0; transferred 13/13 [ 7385.332950] usb-storage: -- transfer complete [ 7385.332954] usb-storage: Bulk status result = 0 [ 7385.332957] usb-storage: Bulk Status S 0x53425355 T 0x20 R 0 Stat 0x1 [ 7385.332961] usb-storage: -- transport indicates command failure [ 7385.332964] usb-storage: Issuing auto-REQUEST_SENSE [ 7385.332970] usb-storage: Bulk Command S 0x43425355 T 0x21 L 18 F 128 Trg 0 LUN 0 CL 6 [ 7385.332974] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7385.333794] usb-storage: Status code 0; transferred 31/31 [ 7385.333798] usb-storage: -- transfer complete [ 7385.333801] usb-storage: Bulk command transfer result=0 [ 7385.333805] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 7385.348891] usb-storage: Status code 0; transferred 18/18 [ 7385.348895] usb-storage: -- transfer complete [ 7385.348899] usb-storage: Bulk data transfer result 0x0 [ 7385.348901] usb-storage: Attempting to get CSW... [ 7385.348904] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7385.352905] usb-storage: Status code 0; transferred 13/13 [ 7385.352909] usb-storage: -- transfer complete [ 7385.352912] usb-storage: Bulk status result = 0 [ 7385.352915] usb-storage: Bulk Status S 0x53425355 T 0x21 R 0 Stat 0x0 [ 7385.352919] usb-storage: -- Result from auto-sense is 0 [ 7385.352922] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 7385.352927] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 7385.352933] usb-storage: scsi cmd done, result=0x2 [ 7385.352939] usb-storage: *** thread sleeping. [ 7385.352947] usb-storage: queuecommand called [ 7385.352954] usb-storage: *** thread awakened. [ 7385.352957] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7385.352960] usb-storage: 00 00 00 00 00 00 [ 7385.352970] usb-storage: Bulk Command S 0x43425355 T 0x22 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7385.352974] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7385.354796] usb-storage: Status code 0; transferred 31/31 [ 7385.354800] usb-storage: -- transfer complete [ 7385.354803] usb-storage: Bulk command transfer result=0 [ 7385.354806] usb-storage: Attempting to get CSW... [ 7385.354809] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7385.368934] usb-storage: Status code 0; transferred 13/13 [ 7385.368939] usb-storage: -- transfer complete [ 7385.368942] usb-storage: Bulk status result = 0 [ 7385.368946] usb-storage: Bulk Status S 0x53425355 T 0x22 R 0 Stat 0x0 [ 7385.368950] usb-storage: scsi cmd done, result=0x0 [ 7385.368956] usb-storage: *** thread sleeping. [ 7385.368976] usb-storage: queuecommand called [ 7385.368983] usb-storage: *** thread awakened. [ 7385.368987] usb-storage: Command READ_10 (10 bytes) [ 7385.368990] usb-storage: 28 00 00 3c 8b f0 00 00 01 00 [ 7385.369003] usb-storage: Bulk Command S 0x43425355 T 0x23 L 512 F 128 Trg 0 LUN 0 CL 10 [ 7385.369007] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7385.369943] usb-storage: Status code 0; transferred 31/31 [ 7385.369947] usb-storage: -- transfer complete [ 7385.369950] usb-storage: Bulk command transfer result=0 [ 7385.369954] usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries [ 7445.997018] usb-storage: command_abort called [ 7445.997025] usb-storage: usb_stor_stop_transport called [ 7445.997028] usb-storage: -- cancelling sg request [ 7445.997651] usb-storage: Status code -104; transferred 0/512 [ 7445.997655] usb-storage: -- transfer cancelled [ 7445.997658] usb-storage: Bulk data transfer result 0x4 [ 7445.997661] usb-storage: -- command was aborted [ 7445.997666] usb-storage: storage_pre_reset [ 7446.048541] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7446.048550] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7446.099217] usb 1-5: reset high speed USB device using ehci_hcd and address 16 [ 7446.162541] ehci_hcd 0000:00:1d.7: port 5 high speed [ 7446.162547] ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT [ 7446.298746] usb-storage: storage_post_reset [ 7446.298755] usb-storage: usb_reset_device returns 0 [ 7446.298759] usb-storage: scsi command aborted [ 7446.298764] usb-storage: *** thread sleeping. [ 7446.298772] usb-storage: queuecommand called [ 7446.298778] usb-storage: *** thread awakened. [ 7446.298782] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7446.298785] usb-storage: 00 00 00 00 00 00 [ 7446.298795] usb-storage: Bulk Command S 0x43425355 T 0x24 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7446.298799] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7446.298949] usb-storage: Status code 0; transferred 31/31 [ 7446.298952] usb-storage: -- transfer complete [ 7446.298955] usb-storage: Bulk command transfer result=0 [ 7446.298957] usb-storage: Attempting to get CSW... [ 7446.298960] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7446.326006] usb-storage: Status code 0; transferred 13/13 [ 7446.326011] usb-storage: -- transfer complete [ 7446.326014] usb-storage: Bulk status result = 0 [ 7446.326018] usb-storage: Bulk Status S 0x53425355 T 0x24 R 0 Stat 0x1 [ 7446.326021] usb-storage: -- transport indicates command failure [ 7446.326025] usb-storage: Issuing auto-REQUEST_SENSE [ 7446.326031] usb-storage: Bulk Command S 0x43425355 T 0x25 L 18 F 128 Trg 0 LUN 0 CL 6 [ 7446.326035] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7446.326727] usb-storage: Status code 0; transferred 31/31 [ 7446.326730] usb-storage: -- transfer complete [ 7446.326733] usb-storage: Bulk command transfer result=0 [ 7446.326737] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 7446.342086] usb-storage: Status code 0; transferred 18/18 [ 7446.342091] usb-storage: -- transfer complete [ 7446.342095] usb-storage: Bulk data transfer result 0x0 [ 7446.342098] usb-storage: Attempting to get CSW... [ 7446.342101] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7446.346211] usb-storage: Status code 0; transferred 13/13 [ 7446.346215] usb-storage: -- transfer complete [ 7446.346218] usb-storage: Bulk status result = 0 [ 7446.346222] usb-storage: Bulk Status S 0x53425355 T 0x25 R 0 Stat 0x0 [ 7446.346225] usb-storage: -- Result from auto-sense is 0 [ 7446.346229] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 7446.346234] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 7446.346240] usb-storage: scsi cmd done, result=0x2 [ 7446.346246] usb-storage: *** thread sleeping. [ 7446.346254] usb-storage: queuecommand called [ 7446.346260] usb-storage: *** thread awakened. [ 7446.346263] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 7446.346266] usb-storage: 00 00 00 00 00 00 [ 7446.346276] usb-storage: Bulk Command S 0x43425355 T 0x26 L 0 F 0 Trg 0 LUN 0 CL 6 [ 7446.346280] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 7446.346447] usb-storage: Status code 0; transferred 31/31 [ 7446.346451] usb-storage: -- transfer complete [ 7446.346454] usb-storage: Bulk command transfer result=0 [ 7446.346456] usb-storage: Attempting to get CSW... [ 7446.346459] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 7446.362240] usb-storage: Status code 0; transferred 13/13 [ 7446.362245] usb-storage: -- transfer complete [ 7446.362248] usb-storage: Bulk status result = 0 [ 7446.362251] usb-storage: Bulk Status S 0x53425355 T 0x26 R 0 Stat 0x0 [ 7446.362256] usb-storage: scsi cmd done, result=0x0 [ 7446.362262] usb-storage: *** thread sleeping. [ 7446.362279] sd 10:0:0:0: [sdb] Unhandled error code [ 7446.362282] sd 10:0:0:0: [sdb] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK [ 7446.362288] end_request: I/O error, dev sdb, sector 3967984 [ 7446.362293] Buffer I/O error on device sdb, logical block 495998 ---------------------------------------------------------
Attachment:
usbmon.out
Description: Binary data
