Hi!
Here you are.
- On battery:
00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller (rev 21) (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. Device 201f
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 124
Region 0: Memory at df110000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee00278 Data: 0000
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
- on AC:
00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller (rev 21) (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. Device 201f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 126
Region 0: Memory at df110000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee002b8 Data: 0000
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
Not sure I'm seeing much of a difference, but I don't know what you are looking for precisely! ;)
Cheers,
Pierre.
Le mercredi 28 septembre 2016, 09:52:19 NZDT Mathias Nyman a écrit :
> On 27.09.2016 22:28, Pierre de Villemereuil wrote:
> > Hi !
> >
> >> run:
> >> sudo lspci -d :8c31 -vv
> >
> > The command yields nothing, either on AC or battery, with a USB device
> > plugged or not.
> >
> > FYI, here's a 'blank' lspci:
> > > 00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI
>
> Right, -d :8c31 was Lynx Point xhci specific, you got a Sunris Point LP one.
>
> sudo lspci -s 14.0 -vv
>
> should do it
> Sorry about that, the "-vv" are also needed for showing D state and
> PME-enable and PME status
>
> -Mathias
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
