Make the #defines a bit more sensible to read.
Done with:
$ sed -r -i -e 's/\b([A-Z0-9_][A-Za-z0-9_]+)_\b/\U\1\E/g' \
drivers/net/usb/smsc95xx.[ch]
and a little editing of the .h file to realign tabstop define values.
There are 3 [RT]x_COE_<foo> defines that were also uppercased.
No change in defconfig objects.
Signed-off-by: Joe Perches <joe@xxxxxxxxxxx>
---
drivers/net/usb/smsc95xx.c | 198 +++++++++++++--------------
drivers/net/usb/smsc95xx.h | 330 ++++++++++++++++++++++-----------------------
2 files changed, 264 insertions(+), 264 deletions(-)
diff --git a/drivers/net/usb/smsc95xx.c b/drivers/net/usb/smsc95xx.c
index 831aa33..c657fe1 100644
--- a/drivers/net/usb/smsc95xx.c
+++ b/drivers/net/usb/smsc95xx.c
@@ -178,7 +178,7 @@ static int __must_check __smsc95xx_phy_wait_not_busy(struct usbnet *dev,
return ret;
}
- if (!(val & MII_BUSY_))
+ if (!(val & MII_BUSY))
return 0;
} while (!time_after(jiffies, start_time + HZ));
@@ -204,7 +204,7 @@ static int __smsc95xx_mdio_read(struct net_device *netdev, int phy_id, int idx,
/* set the address, index & direction (read from PHY) */
phy_id &= dev->mii.phy_id_mask;
idx &= dev->mii.reg_num_mask;
- addr = (phy_id << 11) | (idx << 6) | MII_READ_ | MII_BUSY_;
+ addr = (phy_id << 11) | (idx << 6) | MII_READ | MII_BUSY;
ret = __smsc95xx_write_reg(dev, MII_ADDR, addr, in_pm);
if (ret < 0) {
netdev_warn(dev->net, "Error writing MII_ADDR\n");
@@ -256,7 +256,7 @@ static void __smsc95xx_mdio_write(struct net_device *netdev, int phy_id,
/* set the address, index & direction (write to PHY) */
phy_id &= dev->mii.phy_id_mask;
idx &= dev->mii.reg_num_mask;
- addr = (phy_id << 11) | (idx << 6) | MII_WRITE_ | MII_BUSY_;
+ addr = (phy_id << 11) | (idx << 6) | MII_WRITE | MII_BUSY;
ret = __smsc95xx_write_reg(dev, MII_ADDR, addr, in_pm);
if (ret < 0) {
netdev_warn(dev->net, "Error writing MII_ADDR\n");
@@ -309,12 +309,12 @@ static int __must_check smsc95xx_wait_eeprom(struct usbnet *dev)
return ret;
}
- if (!(val & E2P_CMD_BUSY_) || (val & E2P_CMD_TIMEOUT_))
+ if (!(val & E2P_CMD_BUSY) || (val & E2P_CMD_TIMEOUT))
break;
udelay(40);
} while (!time_after(jiffies, start_time + HZ));
- if (val & (E2P_CMD_TIMEOUT_ | E2P_CMD_BUSY_)) {
+ if (val & (E2P_CMD_TIMEOUT | E2P_CMD_BUSY)) {
netdev_warn(dev->net, "EEPROM read operation timeout\n");
return -EIO;
}
@@ -335,7 +335,7 @@ static int __must_check smsc95xx_eeprom_confirm_not_busy(struct usbnet *dev)
return ret;
}
- if (!(val & E2P_CMD_BUSY_))
+ if (!(val & E2P_CMD_BUSY))
return 0;
udelay(40);
@@ -359,7 +359,7 @@ static int smsc95xx_read_eeprom(struct usbnet *dev, u32 offset, u32 length,
return ret;
for (i = 0; i < length; i++) {
- val = E2P_CMD_BUSY_ | E2P_CMD_READ_ | (offset & E2P_CMD_ADDR_);
+ val = E2P_CMD_BUSY | E2P_CMD_READ | (offset & E2P_CMD_ADDR);
ret = smsc95xx_write_reg(dev, E2P_CMD, val);
if (ret < 0) {
netdev_warn(dev->net, "Error writing E2P_CMD\n");
@@ -397,7 +397,7 @@ static int smsc95xx_write_eeprom(struct usbnet *dev, u32 offset, u32 length,
return ret;
/* Issue write/erase enable command */
- val = E2P_CMD_BUSY_ | E2P_CMD_EWEN_;
+ val = E2P_CMD_BUSY | E2P_CMD_EWEN;
ret = smsc95xx_write_reg(dev, E2P_CMD, val);
if (ret < 0) {
netdev_warn(dev->net, "Error writing E2P_DATA\n");
@@ -419,7 +419,7 @@ static int smsc95xx_write_eeprom(struct usbnet *dev, u32 offset, u32 length,
}
/* Send "write" command */
- val = E2P_CMD_BUSY_ | E2P_CMD_WRITE_ | (offset & E2P_CMD_ADDR_);
+ val = E2P_CMD_BUSY | E2P_CMD_WRITE | (offset & E2P_CMD_ADDR);
ret = smsc95xx_write_reg(dev, E2P_CMD, val);
if (ret < 0) {
netdev_warn(dev->net, "Error writing E2P_CMD\n");
@@ -478,17 +478,17 @@ static void smsc95xx_set_multicast(struct net_device *netdev)
if (dev->net->flags & IFF_PROMISC) {
netif_dbg(dev, drv, dev->net, "promiscuous mode enabled\n");
- pdata->mac_cr |= MAC_CR_PRMS_;
- pdata->mac_cr &= ~(MAC_CR_MCPAS_ | MAC_CR_HPFILT_);
+ pdata->mac_cr |= MAC_CR_PRMS;
+ pdata->mac_cr &= ~(MAC_CR_MCPAS | MAC_CR_HPFILT);
} else if (dev->net->flags & IFF_ALLMULTI) {
netif_dbg(dev, drv, dev->net, "receive all multicast enabled\n");
- pdata->mac_cr |= MAC_CR_MCPAS_;
- pdata->mac_cr &= ~(MAC_CR_PRMS_ | MAC_CR_HPFILT_);
+ pdata->mac_cr |= MAC_CR_MCPAS;
+ pdata->mac_cr &= ~(MAC_CR_PRMS | MAC_CR_HPFILT);
} else if (!netdev_mc_empty(dev->net)) {
struct netdev_hw_addr *ha;
- pdata->mac_cr |= MAC_CR_HPFILT_;
- pdata->mac_cr &= ~(MAC_CR_PRMS_ | MAC_CR_MCPAS_);
+ pdata->mac_cr |= MAC_CR_HPFILT;
+ pdata->mac_cr &= ~(MAC_CR_PRMS | MAC_CR_MCPAS);
netdev_for_each_mc_addr(ha, netdev) {
u32 bitnum = smsc95xx_hash(ha->addr);
@@ -504,7 +504,7 @@ static void smsc95xx_set_multicast(struct net_device *netdev)
} else {
netif_dbg(dev, drv, dev->net, "receive own packets only\n");
pdata->mac_cr &=
- ~(MAC_CR_PRMS_ | MAC_CR_MCPAS_ | MAC_CR_HPFILT_);
+ ~(MAC_CR_PRMS | MAC_CR_MCPAS | MAC_CR_HPFILT);
}
spin_unlock_irqrestore(&pdata->mac_cr_lock, flags);
@@ -575,7 +575,7 @@ static int smsc95xx_link_reset(struct usbnet *dev)
if (ret < 0)
return ret;
- ret = smsc95xx_write_reg(dev, INT_STS, INT_STS_CLEAR_ALL_);
+ ret = smsc95xx_write_reg(dev, INT_STS, INT_STS_CLEAR_ALL);
if (ret < 0)
return ret;
@@ -590,11 +590,11 @@ static int smsc95xx_link_reset(struct usbnet *dev)
spin_lock_irqsave(&pdata->mac_cr_lock, flags);
if (ecmd.duplex != DUPLEX_FULL) {
- pdata->mac_cr &= ~MAC_CR_FDPX_;
- pdata->mac_cr |= MAC_CR_RCVOWN_;
+ pdata->mac_cr &= ~MAC_CR_FDPX;
+ pdata->mac_cr |= MAC_CR_RCVOWN;
} else {
- pdata->mac_cr &= ~MAC_CR_RCVOWN_;
- pdata->mac_cr |= MAC_CR_FDPX_;
+ pdata->mac_cr &= ~MAC_CR_RCVOWN;
+ pdata->mac_cr |= MAC_CR_FDPX;
}
spin_unlock_irqrestore(&pdata->mac_cr_lock, flags);
@@ -624,7 +624,7 @@ static void smsc95xx_status(struct usbnet *dev, struct urb *urb)
netif_dbg(dev, link, dev->net, "intdata: 0x%08X\n", intdata);
- if (intdata & INT_ENP_PHY_INT_)
+ if (intdata & INT_ENP_PHY_INT)
usbnet_defer_kevent(dev, EVENT_LINK_RESET);
else
netdev_warn(dev->net, "unexpected interrupt, intdata=0x%08X\n",
@@ -682,14 +682,14 @@ static int smsc95xx_set_features(struct net_device *netdev,
return ret;
if (features & NETIF_F_HW_CSUM)
- read_buf |= Tx_COE_EN_;
+ read_buf |= TX_COE_EN;
else
- read_buf &= ~Tx_COE_EN_;
+ read_buf &= ~TX_COE_EN;
if (features & NETIF_F_RXCSUM)
- read_buf |= Rx_COE_EN_;
+ read_buf |= RX_COE_EN;
else
- read_buf &= ~Rx_COE_EN_;
+ read_buf &= ~RX_COE_EN;
ret = smsc95xx_write_reg(dev, COE_CR, read_buf);
if (ret < 0)
@@ -791,14 +791,14 @@ static int get_mdix_status(struct net_device *net)
int buf;
buf = smsc95xx_mdio_read(dev->net, dev->mii.phy_id, SPECIAL_CTRL_STS);
- if (buf & SPECIAL_CTRL_STS_OVRRD_AMDIX_) {
- if (buf & SPECIAL_CTRL_STS_AMDIX_ENABLE_)
+ if (buf & SPECIAL_CTRL_STS_OVRRD_AMDIX) {
+ if (buf & SPECIAL_CTRL_STS_AMDIX_ENABLE)
return ETH_TP_MDI_AUTO;
- else if (buf & SPECIAL_CTRL_STS_AMDIX_STATE_)
+ else if (buf & SPECIAL_CTRL_STS_AMDIX_STATE)
return ETH_TP_MDI_X;
} else {
buf = smsc95xx_read_reg(dev, STRAP_STATUS, &val);
- if (val & STRAP_STATUS_AMDIX_EN_)
+ if (val & STRAP_STATUS_AMDIX_EN)
return ETH_TP_MDI_AUTO;
}
@@ -811,14 +811,14 @@ static void set_mdix_status(struct net_device *net, __u8 mdix_ctrl)
struct smsc95xx_priv *pdata = (struct smsc95xx_priv *)(dev->data[0]);
int buf;
- if ((pdata->chip_id == ID_REV_CHIP_ID_9500A_) ||
- (pdata->chip_id == ID_REV_CHIP_ID_9530_) ||
- (pdata->chip_id == ID_REV_CHIP_ID_89530_) ||
- (pdata->chip_id == ID_REV_CHIP_ID_9730_)) {
+ if ((pdata->chip_id == ID_REV_CHIP_ID_9500A) ||
+ (pdata->chip_id == ID_REV_CHIP_ID_9530) ||
+ (pdata->chip_id == ID_REV_CHIP_ID_89530) ||
+ (pdata->chip_id == ID_REV_CHIP_ID_9730)) {
/* Extend Manual AutoMDIX timer for 9500A/9500Ai */
buf = smsc95xx_mdio_read(dev->net, dev->mii.phy_id,
PHY_EDPD_CONFIG);
- buf |= PHY_EDPD_CONFIG_EXT_CROSSOVER_;
+ buf |= PHY_EDPD_CONFIG_EXT_CROSSOVER;
smsc95xx_mdio_write(dev->net, dev->mii.phy_id,
PHY_EDPD_CONFIG, buf);
}
@@ -826,27 +826,27 @@ static void set_mdix_status(struct net_device *net, __u8 mdix_ctrl)
if (mdix_ctrl == ETH_TP_MDI) {
buf = smsc95xx_mdio_read(dev->net, dev->mii.phy_id,
SPECIAL_CTRL_STS);
- buf |= SPECIAL_CTRL_STS_OVRRD_AMDIX_;
- buf &= ~(SPECIAL_CTRL_STS_AMDIX_ENABLE_ |
- SPECIAL_CTRL_STS_AMDIX_STATE_);
+ buf |= SPECIAL_CTRL_STS_OVRRD_AMDIX;
+ buf &= ~(SPECIAL_CTRL_STS_AMDIX_ENABLE |
+ SPECIAL_CTRL_STS_AMDIX_STATE);
smsc95xx_mdio_write(dev->net, dev->mii.phy_id,
SPECIAL_CTRL_STS, buf);
} else if (mdix_ctrl == ETH_TP_MDI_X) {
buf = smsc95xx_mdio_read(dev->net, dev->mii.phy_id,
SPECIAL_CTRL_STS);
- buf |= SPECIAL_CTRL_STS_OVRRD_AMDIX_;
- buf &= ~(SPECIAL_CTRL_STS_AMDIX_ENABLE_ |
- SPECIAL_CTRL_STS_AMDIX_STATE_);
- buf |= SPECIAL_CTRL_STS_AMDIX_STATE_;
+ buf |= SPECIAL_CTRL_STS_OVRRD_AMDIX;
+ buf &= ~(SPECIAL_CTRL_STS_AMDIX_ENABLE |
+ SPECIAL_CTRL_STS_AMDIX_STATE);
+ buf |= SPECIAL_CTRL_STS_AMDIX_STATE;
smsc95xx_mdio_write(dev->net, dev->mii.phy_id,
SPECIAL_CTRL_STS, buf);
} else if (mdix_ctrl == ETH_TP_MDI_AUTO) {
buf = smsc95xx_mdio_read(dev->net, dev->mii.phy_id,
SPECIAL_CTRL_STS);
- buf &= ~SPECIAL_CTRL_STS_OVRRD_AMDIX_;
- buf &= ~(SPECIAL_CTRL_STS_AMDIX_ENABLE_ |
- SPECIAL_CTRL_STS_AMDIX_STATE_);
- buf |= SPECIAL_CTRL_STS_AMDIX_ENABLE_;
+ buf &= ~SPECIAL_CTRL_STS_OVRRD_AMDIX;
+ buf &= ~(SPECIAL_CTRL_STS_AMDIX_ENABLE |
+ SPECIAL_CTRL_STS_AMDIX_STATE);
+ buf |= SPECIAL_CTRL_STS_AMDIX_ENABLE;
smsc95xx_mdio_write(dev->net, dev->mii.phy_id,
SPECIAL_CTRL_STS, buf);
}
@@ -959,7 +959,7 @@ static int smsc95xx_start_tx_path(struct usbnet *dev)
/* Enable Tx at MAC */
spin_lock_irqsave(&pdata->mac_cr_lock, flags);
- pdata->mac_cr |= MAC_CR_TXEN_;
+ pdata->mac_cr |= MAC_CR_TXEN;
spin_unlock_irqrestore(&pdata->mac_cr_lock, flags);
ret = smsc95xx_write_reg(dev, MAC_CR, pdata->mac_cr);
@@ -967,7 +967,7 @@ static int smsc95xx_start_tx_path(struct usbnet *dev)
return ret;
/* Enable Tx at SCSRs */
- return smsc95xx_write_reg(dev, TX_CFG, TX_CFG_ON_);
+ return smsc95xx_write_reg(dev, TX_CFG, TX_CFG_ON);
}
/* Starts the Receive path */
@@ -977,7 +977,7 @@ static int smsc95xx_start_rx_path(struct usbnet *dev, int in_pm)
unsigned long flags;
spin_lock_irqsave(&pdata->mac_cr_lock, flags);
- pdata->mac_cr |= MAC_CR_RXEN_;
+ pdata->mac_cr |= MAC_CR_RXEN;
spin_unlock_irqrestore(&pdata->mac_cr_lock, flags);
return __smsc95xx_write_reg(dev, MAC_CR, pdata->mac_cr, in_pm);
@@ -1021,7 +1021,7 @@ static int smsc95xx_phy_initialize(struct usbnet *dev)
}
smsc95xx_mdio_write(dev->net, dev->mii.phy_id, PHY_INT_MASK,
- PHY_INT_MASK_DEFAULT_);
+ PHY_INT_MASK_DEFAULT);
mii_nway_restart(&dev->mii);
netif_dbg(dev, ifup, dev->net, "phy initialised successfully\n");
@@ -1036,7 +1036,7 @@ static int smsc95xx_reset(struct usbnet *dev)
netif_dbg(dev, ifup, dev->net, "entering smsc95xx_reset\n");
- ret = smsc95xx_write_reg(dev, HW_CFG, HW_CFG_LRST_);
+ ret = smsc95xx_write_reg(dev, HW_CFG, HW_CFG_LRST);
if (ret < 0)
return ret;
@@ -1047,14 +1047,14 @@ static int smsc95xx_reset(struct usbnet *dev)
if (ret < 0)
return ret;
timeout++;
- } while ((read_buf & HW_CFG_LRST_) && (timeout < 100));
+ } while ((read_buf & HW_CFG_LRST) && (timeout < 100));
if (timeout >= 100) {
netdev_warn(dev->net, "timeout waiting for completion of Lite Reset\n");
return ret;
}
- ret = smsc95xx_write_reg(dev, PM_CTRL, PM_CTL_PHY_RST_);
+ ret = smsc95xx_write_reg(dev, PM_CTRL, PM_CTL_PHY_RST);
if (ret < 0)
return ret;
@@ -1065,7 +1065,7 @@ static int smsc95xx_reset(struct usbnet *dev)
if (ret < 0)
return ret;
timeout++;
- } while ((read_buf & PM_CTL_PHY_RST_) && (timeout < 100));
+ } while ((read_buf & PM_CTL_PHY_RST) && (timeout < 100));
if (timeout >= 100) {
netdev_warn(dev->net, "timeout waiting for PHY Reset\n");
@@ -1086,7 +1086,7 @@ static int smsc95xx_reset(struct usbnet *dev)
netif_dbg(dev, ifup, dev->net, "Read Value from HW_CFG : 0x%08x\n",
read_buf);
- read_buf |= HW_CFG_BIR_;
+ read_buf |= HW_CFG_BIR;
ret = smsc95xx_write_reg(dev, HW_CFG, read_buf);
if (ret < 0)
@@ -1097,7 +1097,7 @@ static int smsc95xx_reset(struct usbnet *dev)
return ret;
netif_dbg(dev, ifup, dev->net,
- "Read Value from HW_CFG after writing HW_CFG_BIR_: 0x%08x\n",
+ "Read Value from HW_CFG after writing HW_CFG_BIR: 0x%08x\n",
read_buf);
if (!turbo_mode) {
@@ -1146,9 +1146,9 @@ static int smsc95xx_reset(struct usbnet *dev)
read_buf);
if (turbo_mode)
- read_buf |= (HW_CFG_MEF_ | HW_CFG_BCE_);
+ read_buf |= (HW_CFG_MEF | HW_CFG_BCE);
- read_buf &= ~HW_CFG_RXDOFF_;
+ read_buf &= ~HW_CFG_RXDOFF;
/* set Rx data offset=2, Make IP header aligns on word boundary. */
read_buf |= NET_IP_ALIGN << 9;
@@ -1164,7 +1164,7 @@ static int smsc95xx_reset(struct usbnet *dev)
netif_dbg(dev, ifup, dev->net,
"Read Value from HW_CFG after writing: 0x%08x\n", read_buf);
- ret = smsc95xx_write_reg(dev, INT_STS, INT_STS_CLEAR_ALL_);
+ ret = smsc95xx_write_reg(dev, INT_STS, INT_STS_CLEAR_ALL);
if (ret < 0)
return ret;
@@ -1220,7 +1220,7 @@ static int smsc95xx_reset(struct usbnet *dev)
return ret;
/* enable PHY interrupts */
- read_buf |= INT_EP_CTL_PHY_INT_;
+ read_buf |= INT_EP_CTL_PHY_INT;
ret = smsc95xx_write_reg(dev, INT_EP_CTL, read_buf);
if (ret < 0)
@@ -1298,12 +1298,12 @@ static int smsc95xx_bind(struct usbnet *dev, struct usb_interface *intf)
pdata->chip_id = val;
pdata->mdix_ctrl = get_mdix_status(dev->net);
- if ((val == ID_REV_CHIP_ID_9500A_) || (val == ID_REV_CHIP_ID_9530_) ||
- (val == ID_REV_CHIP_ID_89530_) || (val == ID_REV_CHIP_ID_9730_))
+ if ((val == ID_REV_CHIP_ID_9500A) || (val == ID_REV_CHIP_ID_9530) ||
+ (val == ID_REV_CHIP_ID_89530) || (val == ID_REV_CHIP_ID_9730))
pdata->features = (FEATURE_8_WAKEUP_FILTERS |
FEATURE_PHY_NLP_CROSSOVER |
FEATURE_REMOTE_WAKEUP);
- else if (val == ID_REV_CHIP_ID_9512_)
+ else if (val == ID_REV_CHIP_ID_9512)
pdata->features = FEATURE_8_WAKEUP_FILTERS;
dev->net->netdev_ops = &smsc95xx_netdev_ops;
@@ -1389,7 +1389,7 @@ static int smsc95xx_enter_suspend0(struct usbnet *dev)
if (ret < 0)
return ret;
- val &= (~(PM_CTL_SUS_MODE_ | PM_CTL_WUPS_ | PM_CTL_PHY_RST_));
+ val &= (~(PM_CTL_SUS_MODE | PM_CTL_WUPS | PM_CTL_PHY_RST));
val |= PM_CTL_SUS_MODE_0;
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
@@ -1397,12 +1397,12 @@ static int smsc95xx_enter_suspend0(struct usbnet *dev)
return ret;
/* clear wol status */
- val &= ~PM_CTL_WUPS_;
- val |= PM_CTL_WUPS_WOL_;
+ val &= ~PM_CTL_WUPS;
+ val |= PM_CTL_WUPS_WOL;
/* enable energy detection */
if (pdata->wolopts & WAKE_PHY)
- val |= PM_CTL_WUPS_ED_;
+ val |= PM_CTL_WUPS_ED;
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
if (ret < 0)
@@ -1437,7 +1437,7 @@ static int smsc95xx_enter_suspend1(struct usbnet *dev)
if (ret < 0)
return ret;
- ret |= MODE_CTRL_STS_EDPWRDOWN_;
+ ret |= MODE_CTRL_STS_EDPWRDOWN;
smsc95xx_mdio_write_nopm(dev->net, mii->phy_id, PHY_MODE_CTRL_STS, ret);
@@ -1446,7 +1446,7 @@ static int smsc95xx_enter_suspend1(struct usbnet *dev)
if (ret < 0)
return ret;
- val &= ~(PM_CTL_SUS_MODE_ | PM_CTL_WUPS_ | PM_CTL_PHY_RST_);
+ val &= ~(PM_CTL_SUS_MODE | PM_CTL_WUPS | PM_CTL_PHY_RST);
val |= PM_CTL_SUS_MODE_1;
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
@@ -1454,8 +1454,8 @@ static int smsc95xx_enter_suspend1(struct usbnet *dev)
return ret;
/* clear wol status, enable energy detection */
- val &= ~PM_CTL_WUPS_;
- val |= (PM_CTL_WUPS_ED_ | PM_CTL_ED_EN_);
+ val &= ~PM_CTL_WUPS;
+ val |= (PM_CTL_WUPS_ED | PM_CTL_ED_EN);
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
if (ret < 0)
@@ -1476,7 +1476,7 @@ static int smsc95xx_enter_suspend2(struct usbnet *dev)
if (ret < 0)
return ret;
- val &= ~(PM_CTL_SUS_MODE_ | PM_CTL_WUPS_ | PM_CTL_PHY_RST_);
+ val &= ~(PM_CTL_SUS_MODE | PM_CTL_WUPS | PM_CTL_PHY_RST);
val |= PM_CTL_SUS_MODE_2;
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
@@ -1507,7 +1507,7 @@ static int smsc95xx_enter_suspend3(struct usbnet *dev)
if (ret < 0)
return ret;
- val &= ~(PM_CTL_SUS_MODE_ | PM_CTL_WUPS_ | PM_CTL_PHY_RST_);
+ val &= ~(PM_CTL_SUS_MODE | PM_CTL_WUPS | PM_CTL_PHY_RST);
val |= PM_CTL_SUS_MODE_3 | PM_CTL_RES_CLR_WKP_STS;
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
@@ -1515,8 +1515,8 @@ static int smsc95xx_enter_suspend3(struct usbnet *dev)
return ret;
/* clear wol status */
- val &= ~PM_CTL_WUPS_;
- val |= PM_CTL_WUPS_WOL_;
+ val &= ~PM_CTL_WUPS;
+ val |= PM_CTL_WUPS_WOL;
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
if (ret < 0)
@@ -1552,7 +1552,7 @@ static int smsc95xx_autosuspend(struct usbnet *dev, u32 link_up)
/* enable PHY wakeup events for if cable is attached */
ret = smsc95xx_enable_phy_wakeup_interrupts(dev,
- PHY_INT_MASK_ANEG_COMP_);
+ PHY_INT_MASK_ANEG_COMP);
if (ret < 0) {
netdev_warn(dev->net, "error enabling PHY wakeup ints\n");
return ret;
@@ -1564,7 +1564,7 @@ static int smsc95xx_autosuspend(struct usbnet *dev, u32 link_up)
/* enable PHY wakeup events so we remote wakeup if cable is pulled */
ret = smsc95xx_enable_phy_wakeup_interrupts(dev,
- PHY_INT_MASK_LINK_DOWN_);
+ PHY_INT_MASK_LINK_DOWN);
if (ret < 0) {
netdev_warn(dev->net, "error enabling PHY wakeup ints\n");
return ret;
@@ -1614,7 +1614,7 @@ static int smsc95xx_suspend(struct usb_interface *intf, pm_message_t message)
if (ret < 0)
goto done;
- val &= ~(WUCSR_MPEN_ | WUCSR_WAKE_EN_);
+ val &= ~(WUCSR_MPEN | WUCSR_WAKE_EN);
ret = smsc95xx_write_reg_nopm(dev, WUCSR, val);
if (ret < 0)
@@ -1624,7 +1624,7 @@ static int smsc95xx_suspend(struct usb_interface *intf, pm_message_t message)
if (ret < 0)
goto done;
- val &= ~(PM_CTL_ED_EN_ | PM_CTL_WOL_EN_);
+ val &= ~(PM_CTL_ED_EN | PM_CTL_WOL_EN);
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
if (ret < 0)
@@ -1636,7 +1636,7 @@ static int smsc95xx_suspend(struct usb_interface *intf, pm_message_t message)
if (pdata->wolopts & WAKE_PHY) {
ret = smsc95xx_enable_phy_wakeup_interrupts(dev,
- (PHY_INT_MASK_ANEG_COMP_ | PHY_INT_MASK_LINK_DOWN_));
+ (PHY_INT_MASK_ANEG_COMP | PHY_INT_MASK_LINK_DOWN));
if (ret < 0) {
netdev_warn(dev->net, "error enabling PHY wakeup ints\n");
goto done;
@@ -1755,7 +1755,7 @@ static int smsc95xx_suspend(struct usb_interface *intf, pm_message_t message)
if (ret < 0)
goto done;
- val |= WUCSR_WUFR_;
+ val |= WUCSR_WUFR;
ret = smsc95xx_write_reg_nopm(dev, WUCSR, val);
if (ret < 0)
@@ -1768,7 +1768,7 @@ static int smsc95xx_suspend(struct usb_interface *intf, pm_message_t message)
if (ret < 0)
goto done;
- val |= WUCSR_MPR_;
+ val |= WUCSR_MPR;
ret = smsc95xx_write_reg_nopm(dev, WUCSR, val);
if (ret < 0)
@@ -1782,18 +1782,18 @@ static int smsc95xx_suspend(struct usb_interface *intf, pm_message_t message)
if (pdata->wolopts & (WAKE_BCAST | WAKE_MCAST | WAKE_ARP | WAKE_UCAST)) {
netdev_info(dev->net, "enabling pattern match wakeup\n");
- val |= WUCSR_WAKE_EN_;
+ val |= WUCSR_WAKE_EN;
} else {
netdev_info(dev->net, "disabling pattern match wakeup\n");
- val &= ~WUCSR_WAKE_EN_;
+ val &= ~WUCSR_WAKE_EN;
}
if (pdata->wolopts & WAKE_MAGIC) {
netdev_info(dev->net, "enabling magic packet wakeup\n");
- val |= WUCSR_MPEN_;
+ val |= WUCSR_MPEN;
} else {
netdev_info(dev->net, "disabling magic packet wakeup\n");
- val &= ~WUCSR_MPEN_;
+ val &= ~WUCSR_MPEN;
}
ret = smsc95xx_write_reg_nopm(dev, WUCSR, val);
@@ -1805,11 +1805,11 @@ static int smsc95xx_suspend(struct usb_interface *intf, pm_message_t message)
if (ret < 0)
goto done;
- val |= PM_CTL_WOL_EN_;
+ val |= PM_CTL_WOL_EN;
/* phy energy detect wakeup source */
if (pdata->wolopts & WAKE_PHY)
- val |= PM_CTL_ED_EN_;
+ val |= PM_CTL_ED_EN;
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
if (ret < 0)
@@ -1856,7 +1856,7 @@ static int smsc95xx_resume(struct usb_interface *intf)
if (ret < 0)
return ret;
- val &= ~(WUCSR_WAKE_EN_ | WUCSR_MPEN_);
+ val &= ~(WUCSR_WAKE_EN | WUCSR_MPEN);
ret = smsc95xx_write_reg_nopm(dev, WUCSR, val);
if (ret < 0)
@@ -1867,8 +1867,8 @@ static int smsc95xx_resume(struct usb_interface *intf)
if (ret < 0)
return ret;
- val &= ~PM_CTL_WOL_EN_;
- val |= PM_CTL_WUPS_;
+ val &= ~PM_CTL_WOL_EN;
+ val |= PM_CTL_WUPS;
ret = smsc95xx_write_reg_nopm(dev, PM_CTRL, val);
if (ret < 0)
@@ -1919,23 +1919,23 @@ static int smsc95xx_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
packet = skb->data;
/* get the packet length */
- size = (u16)((header & RX_STS_FL_) >> 16);
+ size = (u16)((header & RX_STS_FL) >> 16);
align_count = (4 - ((size + NET_IP_ALIGN) % 4)) % 4;
- if (unlikely(header & RX_STS_ES_)) {
+ if (unlikely(header & RX_STS_ES)) {
netif_dbg(dev, rx_err, dev->net,
"Error header=0x%08x\n", header);
dev->net->stats.rx_errors++;
dev->net->stats.rx_dropped++;
- if (header & RX_STS_CRC_) {
+ if (header & RX_STS_CRC) {
dev->net->stats.rx_crc_errors++;
} else {
- if (header & (RX_STS_TL_ | RX_STS_RF_))
+ if (header & (RX_STS_TL | RX_STS_RF))
dev->net->stats.rx_frame_errors++;
- if ((header & RX_STS_LE_) &&
- (!(header & RX_STS_FT_)))
+ if ((header & RX_STS_LE) &&
+ (!(header & RX_STS_FT)))
dev->net->stats.rx_length_errors++;
}
} else {
@@ -2037,8 +2037,8 @@ static struct sk_buff *smsc95xx_tx_fixup(struct usbnet *dev,
memcpy(skb->data, &tx_cmd_b, 4);
skb_push(skb, 4);
- tx_cmd_a = (u32)(skb->len - 8) | TX_CMD_A_FIRST_SEG_ |
- TX_CMD_A_LAST_SEG_;
+ tx_cmd_a = (u32)(skb->len - 8) | TX_CMD_A_FIRST_SEG |
+ TX_CMD_A_LAST_SEG;
cpu_to_le32s(&tx_cmd_a);
memcpy(skb->data, &tx_cmd_a, 4);
diff --git a/drivers/net/usb/smsc95xx.h b/drivers/net/usb/smsc95xx.h
index 29a4d9e..6d51424 100644
--- a/drivers/net/usb/smsc95xx.h
+++ b/drivers/net/usb/smsc95xx.h
@@ -21,91 +21,91 @@
#define _SMSC95XX_H
/* Tx command words */
-#define TX_CMD_A_DATA_OFFSET_ (0x001F0000)
-#define TX_CMD_A_FIRST_SEG_ (0x00002000)
-#define TX_CMD_A_LAST_SEG_ (0x00001000)
-#define TX_CMD_A_BUF_SIZE_ (0x000007FF)
+#define TX_CMD_A_DATA_OFFSET (0x001F0000)
+#define TX_CMD_A_FIRST_SEG (0x00002000)
+#define TX_CMD_A_LAST_SEG (0x00001000)
+#define TX_CMD_A_BUF_SIZE (0x000007FF)
#define TX_CMD_B_CSUM_ENABLE (0x00004000)
-#define TX_CMD_B_ADD_CRC_DISABLE_ (0x00002000)
-#define TX_CMD_B_DISABLE_PADDING_ (0x00001000)
-#define TX_CMD_B_PKT_BYTE_LENGTH_ (0x000007FF)
+#define TX_CMD_B_ADD_CRC_DISABLE (0x00002000)
+#define TX_CMD_B_DISABLE_PADDING (0x00001000)
+#define TX_CMD_B_PKT_BYTE_LENGTH (0x000007FF)
/* Rx status word */
-#define RX_STS_FF_ (0x40000000) /* Filter Fail */
-#define RX_STS_FL_ (0x3FFF0000) /* Frame Length */
-#define RX_STS_ES_ (0x00008000) /* Error Summary */
-#define RX_STS_BF_ (0x00002000) /* Broadcast Frame */
-#define RX_STS_LE_ (0x00001000) /* Length Error */
-#define RX_STS_RF_ (0x00000800) /* Runt Frame */
-#define RX_STS_MF_ (0x00000400) /* Multicast Frame */
-#define RX_STS_TL_ (0x00000080) /* Frame too long */
-#define RX_STS_CS_ (0x00000040) /* Collision Seen */
-#define RX_STS_FT_ (0x00000020) /* Frame Type */
-#define RX_STS_RW_ (0x00000010) /* Receive Watchdog */
-#define RX_STS_ME_ (0x00000008) /* Mii Error */
-#define RX_STS_DB_ (0x00000004) /* Dribbling */
-#define RX_STS_CRC_ (0x00000002) /* CRC Error */
+#define RX_STS_FF (0x40000000) /* Filter Fail */
+#define RX_STS_FL (0x3FFF0000) /* Frame Length */
+#define RX_STS_ES (0x00008000) /* Error Summary */
+#define RX_STS_BF (0x00002000) /* Broadcast Frame */
+#define RX_STS_LE (0x00001000) /* Length Error */
+#define RX_STS_RF (0x00000800) /* Runt Frame */
+#define RX_STS_MF (0x00000400) /* Multicast Frame */
+#define RX_STS_TL (0x00000080) /* Frame too long */
+#define RX_STS_CS (0x00000040) /* Collision Seen */
+#define RX_STS_FT (0x00000020) /* Frame Type */
+#define RX_STS_RW (0x00000010) /* Receive Watchdog */
+#define RX_STS_ME (0x00000008) /* Mii Error */
+#define RX_STS_DB (0x00000004) /* Dribbling */
+#define RX_STS_CRC (0x00000002) /* CRC Error */
/* SCSRs */
#define ID_REV (0x00)
-#define ID_REV_CHIP_ID_MASK_ (0xFFFF0000)
-#define ID_REV_CHIP_REV_MASK_ (0x0000FFFF)
-#define ID_REV_CHIP_ID_9500_ (0x9500)
-#define ID_REV_CHIP_ID_9500A_ (0x9E00)
-#define ID_REV_CHIP_ID_9512_ (0xEC00)
-#define ID_REV_CHIP_ID_9530_ (0x9530)
-#define ID_REV_CHIP_ID_89530_ (0x9E08)
-#define ID_REV_CHIP_ID_9730_ (0x9730)
+#define ID_REV_CHIP_ID_MASK (0xFFFF0000)
+#define ID_REV_CHIP_REV_MASK (0x0000FFFF)
+#define ID_REV_CHIP_ID_9500 (0x9500)
+#define ID_REV_CHIP_ID_9500A (0x9E00)
+#define ID_REV_CHIP_ID_9512 (0xEC00)
+#define ID_REV_CHIP_ID_9530 (0x9530)
+#define ID_REV_CHIP_ID_89530 (0x9E08)
+#define ID_REV_CHIP_ID_9730 (0x9730)
#define INT_STS (0x08)
-#define INT_STS_TX_STOP_ (0x00020000)
-#define INT_STS_RX_STOP_ (0x00010000)
-#define INT_STS_PHY_INT_ (0x00008000)
-#define INT_STS_TXE_ (0x00004000)
-#define INT_STS_TDFU_ (0x00002000)
-#define INT_STS_TDFO_ (0x00001000)
-#define INT_STS_RXDF_ (0x00000800)
-#define INT_STS_GPIOS_ (0x000007FF)
-#define INT_STS_CLEAR_ALL_ (0xFFFFFFFF)
+#define INT_STS_TX_STOP (0x00020000)
+#define INT_STS_RX_STOP (0x00010000)
+#define INT_STS_PHY_INT (0x00008000)
+#define INT_STS_TXE (0x00004000)
+#define INT_STS_TDFU (0x00002000)
+#define INT_STS_TDFO (0x00001000)
+#define INT_STS_RXDF (0x00000800)
+#define INT_STS_GPIOS (0x000007FF)
+#define INT_STS_CLEAR_ALL (0xFFFFFFFF)
#define RX_CFG (0x0C)
-#define RX_FIFO_FLUSH_ (0x00000001)
+#define RX_FIFO_FLUSH (0x00000001)
#define TX_CFG (0x10)
-#define TX_CFG_ON_ (0x00000004)
-#define TX_CFG_STOP_ (0x00000002)
-#define TX_CFG_FIFO_FLUSH_ (0x00000001)
+#define TX_CFG_ON (0x00000004)
+#define TX_CFG_STOP (0x00000002)
+#define TX_CFG_FIFO_FLUSH (0x00000001)
#define HW_CFG (0x14)
-#define HW_CFG_BIR_ (0x00001000)
-#define HW_CFG_LEDB_ (0x00000800)
-#define HW_CFG_RXDOFF_ (0x00000600)
-#define HW_CFG_DRP_ (0x00000040)
-#define HW_CFG_MEF_ (0x00000020)
-#define HW_CFG_LRST_ (0x00000008)
-#define HW_CFG_PSEL_ (0x00000004)
-#define HW_CFG_BCE_ (0x00000002)
-#define HW_CFG_SRST_ (0x00000001)
+#define HW_CFG_BIR (0x00001000)
+#define HW_CFG_LEDB (0x00000800)
+#define HW_CFG_RXDOFF (0x00000600)
+#define HW_CFG_DRP (0x00000040)
+#define HW_CFG_MEF (0x00000020)
+#define HW_CFG_LRST (0x00000008)
+#define HW_CFG_PSEL (0x00000004)
+#define HW_CFG_BCE (0x00000002)
+#define HW_CFG_SRST (0x00000001)
#define RX_FIFO_INF (0x18)
#define PM_CTRL (0x20)
#define PM_CTL_RES_CLR_WKP_STS (0x00000200)
-#define PM_CTL_DEV_RDY_ (0x00000080)
-#define PM_CTL_SUS_MODE_ (0x00000060)
+#define PM_CTL_DEV_RDY (0x00000080)
+#define PM_CTL_SUS_MODE (0x00000060)
#define PM_CTL_SUS_MODE_0 (0x00000000)
#define PM_CTL_SUS_MODE_1 (0x00000020)
#define PM_CTL_SUS_MODE_2 (0x00000040)
#define PM_CTL_SUS_MODE_3 (0x00000060)
-#define PM_CTL_PHY_RST_ (0x00000010)
-#define PM_CTL_WOL_EN_ (0x00000008)
-#define PM_CTL_ED_EN_ (0x00000004)
-#define PM_CTL_WUPS_ (0x00000003)
-#define PM_CTL_WUPS_NO_ (0x00000000)
-#define PM_CTL_WUPS_ED_ (0x00000001)
-#define PM_CTL_WUPS_WOL_ (0x00000002)
-#define PM_CTL_WUPS_MULTI_ (0x00000003)
+#define PM_CTL_PHY_RST (0x00000010)
+#define PM_CTL_WOL_EN (0x00000008)
+#define PM_CTL_ED_EN (0x00000004)
+#define PM_CTL_WUPS (0x00000003)
+#define PM_CTL_WUPS_NO (0x00000000)
+#define PM_CTL_WUPS_ED (0x00000001)
+#define PM_CTL_WUPS_WOL (0x00000002)
+#define PM_CTL_WUPS_MULTI (0x00000003)
#define LED_GPIO_CFG (0x24)
#define LED_GPIO_CFG_SPD_LED (0x01000000)
@@ -123,71 +123,71 @@
#define AFC_CFG_DEFAULT (0x00F830A1)
#define E2P_CMD (0x30)
-#define E2P_CMD_BUSY_ (0x80000000)
-#define E2P_CMD_MASK_ (0x70000000)
-#define E2P_CMD_READ_ (0x00000000)
-#define E2P_CMD_EWDS_ (0x10000000)
-#define E2P_CMD_EWEN_ (0x20000000)
-#define E2P_CMD_WRITE_ (0x30000000)
-#define E2P_CMD_WRAL_ (0x40000000)
-#define E2P_CMD_ERASE_ (0x50000000)
-#define E2P_CMD_ERAL_ (0x60000000)
-#define E2P_CMD_RELOAD_ (0x70000000)
-#define E2P_CMD_TIMEOUT_ (0x00000400)
-#define E2P_CMD_LOADED_ (0x00000200)
-#define E2P_CMD_ADDR_ (0x000001FF)
+#define E2P_CMD_BUSY (0x80000000)
+#define E2P_CMD_MASK (0x70000000)
+#define E2P_CMD_READ (0x00000000)
+#define E2P_CMD_EWDS (0x10000000)
+#define E2P_CMD_EWEN (0x20000000)
+#define E2P_CMD_WRITE (0x30000000)
+#define E2P_CMD_WRAL (0x40000000)
+#define E2P_CMD_ERASE (0x50000000)
+#define E2P_CMD_ERAL (0x60000000)
+#define E2P_CMD_RELOAD (0x70000000)
+#define E2P_CMD_TIMEOUT (0x00000400)
+#define E2P_CMD_LOADED (0x00000200)
+#define E2P_CMD_ADDR (0x000001FF)
#define MAX_EEPROM_SIZE (512)
#define E2P_DATA (0x34)
-#define E2P_DATA_MASK_ (0x000000FF)
+#define E2P_DATA_MASK (0x000000FF)
#define BURST_CAP (0x38)
#define STRAP_STATUS (0x3C)
-#define STRAP_STATUS_PWR_SEL_ (0x00000020)
-#define STRAP_STATUS_AMDIX_EN_ (0x00000010)
-#define STRAP_STATUS_PORT_SWAP_ (0x00000008)
-#define STRAP_STATUS_EEP_SIZE_ (0x00000004)
-#define STRAP_STATUS_RMT_WKP_ (0x00000002)
-#define STRAP_STATUS_EEP_DISABLE_ (0x00000001)
+#define STRAP_STATUS_PWR_SEL (0x00000020)
+#define STRAP_STATUS_AMDIX_EN (0x00000010)
+#define STRAP_STATUS_PORT_SWAP (0x00000008)
+#define STRAP_STATUS_EEP_SIZE (0x00000004)
+#define STRAP_STATUS_RMT_WKP (0x00000002)
+#define STRAP_STATUS_EEP_DISABLE (0x00000001)
#define GPIO_WAKE (0x64)
#define INT_EP_CTL (0x68)
-#define INT_EP_CTL_INTEP_ (0x80000000)
-#define INT_EP_CTL_MACRTO_ (0x00080000)
-#define INT_EP_CTL_TX_STOP_ (0x00020000)
-#define INT_EP_CTL_RX_STOP_ (0x00010000)
-#define INT_EP_CTL_PHY_INT_ (0x00008000)
-#define INT_EP_CTL_TXE_ (0x00004000)
-#define INT_EP_CTL_TDFU_ (0x00002000)
-#define INT_EP_CTL_TDFO_ (0x00001000)
-#define INT_EP_CTL_RXDF_ (0x00000800)
-#define INT_EP_CTL_GPIOS_ (0x000007FF)
+#define INT_EP_CTL_INTEP (0x80000000)
+#define INT_EP_CTL_MACRTO (0x00080000)
+#define INT_EP_CTL_TX_STOP (0x00020000)
+#define INT_EP_CTL_RX_STOP (0x00010000)
+#define INT_EP_CTL_PHY_INT (0x00008000)
+#define INT_EP_CTL_TXE (0x00004000)
+#define INT_EP_CTL_TDFU (0x00002000)
+#define INT_EP_CTL_TDFO (0x00001000)
+#define INT_EP_CTL_RXDF (0x00000800)
+#define INT_EP_CTL_GPIOS (0x000007FF)
#define BULK_IN_DLY (0x6C)
/* MAC CSRs */
#define MAC_CR (0x100)
-#define MAC_CR_RXALL_ (0x80000000)
-#define MAC_CR_RCVOWN_ (0x00800000)
-#define MAC_CR_LOOPBK_ (0x00200000)
-#define MAC_CR_FDPX_ (0x00100000)
-#define MAC_CR_MCPAS_ (0x00080000)
-#define MAC_CR_PRMS_ (0x00040000)
-#define MAC_CR_INVFILT_ (0x00020000)
-#define MAC_CR_PASSBAD_ (0x00010000)
-#define MAC_CR_HFILT_ (0x00008000)
-#define MAC_CR_HPFILT_ (0x00002000)
-#define MAC_CR_LCOLL_ (0x00001000)
-#define MAC_CR_BCAST_ (0x00000800)
-#define MAC_CR_DISRTY_ (0x00000400)
-#define MAC_CR_PADSTR_ (0x00000100)
+#define MAC_CR_RXALL (0x80000000)
+#define MAC_CR_RCVOWN (0x00800000)
+#define MAC_CR_LOOPBK (0x00200000)
+#define MAC_CR_FDPX (0x00100000)
+#define MAC_CR_MCPAS (0x00080000)
+#define MAC_CR_PRMS (0x00040000)
+#define MAC_CR_INVFILT (0x00020000)
+#define MAC_CR_PASSBAD (0x00010000)
+#define MAC_CR_HFILT (0x00008000)
+#define MAC_CR_HPFILT (0x00002000)
+#define MAC_CR_LCOLL (0x00001000)
+#define MAC_CR_BCAST (0x00000800)
+#define MAC_CR_DISRTY (0x00000400)
+#define MAC_CR_PADSTR (0x00000100)
#define MAC_CR_BOLMT_MASK (0x000000C0)
-#define MAC_CR_DFCHK_ (0x00000020)
-#define MAC_CR_TXEN_ (0x00000008)
-#define MAC_CR_RXEN_ (0x00000004)
+#define MAC_CR_DFCHK (0x00000020)
+#define MAC_CR_TXEN (0x00000008)
+#define MAC_CR_RXEN (0x00000004)
#define ADDRH (0x104)
@@ -198,17 +198,17 @@
#define HASHL (0x110)
#define MII_ADDR (0x114)
-#define MII_WRITE_ (0x02)
-#define MII_BUSY_ (0x01)
-#define MII_READ_ (0x00) /* ~of MII Write bit */
+#define MII_WRITE (0x02)
+#define MII_BUSY (0x01)
+#define MII_READ (0x00) /* ~of MII Write bit */
#define MII_DATA (0x118)
#define FLOW (0x11C)
-#define FLOW_FCPT_ (0xFFFF0000)
-#define FLOW_FCPASS_ (0x00000004)
-#define FLOW_FCEN_ (0x00000002)
-#define FLOW_FCBSY_ (0x00000001)
+#define FLOW_FCPT (0xFFFF0000)
+#define FLOW_FCPASS (0x00000004)
+#define FLOW_FCEN (0x00000002)
+#define FLOW_FCBSY (0x00000001)
#define VLAN1 (0x120)
@@ -219,67 +219,67 @@
#define LAN9500A_WUFF_NUM (8)
#define WUCSR (0x12C)
-#define WUCSR_WFF_PTR_RST_ (0x80000000)
-#define WUCSR_GUE_ (0x00000200)
-#define WUCSR_WUFR_ (0x00000040)
-#define WUCSR_MPR_ (0x00000020)
-#define WUCSR_WAKE_EN_ (0x00000004)
-#define WUCSR_MPEN_ (0x00000002)
+#define WUCSR_WFF_PTR_RST (0x80000000)
+#define WUCSR_GUE (0x00000200)
+#define WUCSR_WUFR (0x00000040)
+#define WUCSR_MPR (0x00000020)
+#define WUCSR_WAKE_EN (0x00000004)
+#define WUCSR_MPEN (0x00000002)
#define COE_CR (0x130)
-#define Tx_COE_EN_ (0x00010000)
-#define Rx_COE_MODE_ (0x00000002)
-#define Rx_COE_EN_ (0x00000001)
+#define TX_COE_EN (0x00010000)
+#define RX_COE_MODE (0x00000002)
+#define RX_COE_EN (0x00000001)
/* Vendor-specific PHY Definitions */
/* EDPD NLP / crossover time configuration (LAN9500A only) */
#define PHY_EDPD_CONFIG (16)
-#define PHY_EDPD_CONFIG_TX_NLP_EN_ ((u16)0x8000)
-#define PHY_EDPD_CONFIG_TX_NLP_1000_ ((u16)0x0000)
-#define PHY_EDPD_CONFIG_TX_NLP_768_ ((u16)0x2000)
-#define PHY_EDPD_CONFIG_TX_NLP_512_ ((u16)0x4000)
-#define PHY_EDPD_CONFIG_TX_NLP_256_ ((u16)0x6000)
-#define PHY_EDPD_CONFIG_RX_1_NLP_ ((u16)0x1000)
-#define PHY_EDPD_CONFIG_RX_NLP_64_ ((u16)0x0000)
-#define PHY_EDPD_CONFIG_RX_NLP_256_ ((u16)0x0400)
-#define PHY_EDPD_CONFIG_RX_NLP_512_ ((u16)0x0800)
-#define PHY_EDPD_CONFIG_RX_NLP_1000_ ((u16)0x0C00)
-#define PHY_EDPD_CONFIG_EXT_CROSSOVER_ ((u16)0x0001)
-#define PHY_EDPD_CONFIG_DEFAULT (PHY_EDPD_CONFIG_TX_NLP_EN_ | \
- PHY_EDPD_CONFIG_TX_NLP_768_ | \
- PHY_EDPD_CONFIG_RX_1_NLP_)
+#define PHY_EDPD_CONFIG_TX_NLP_EN ((u16)0x8000)
+#define PHY_EDPD_CONFIG_TX_NLP_1000 ((u16)0x0000)
+#define PHY_EDPD_CONFIG_TX_NLP_768 ((u16)0x2000)
+#define PHY_EDPD_CONFIG_TX_NLP_512 ((u16)0x4000)
+#define PHY_EDPD_CONFIG_TX_NLP_256 ((u16)0x6000)
+#define PHY_EDPD_CONFIG_RX_1_NLP ((u16)0x1000)
+#define PHY_EDPD_CONFIG_RX_NLP_64 ((u16)0x0000)
+#define PHY_EDPD_CONFIG_RX_NLP_256 ((u16)0x0400)
+#define PHY_EDPD_CONFIG_RX_NLP_512 ((u16)0x0800)
+#define PHY_EDPD_CONFIG_RX_NLP_1000 ((u16)0x0C00)
+#define PHY_EDPD_CONFIG_EXT_CROSSOVER ((u16)0x0001)
+#define PHY_EDPD_CONFIG_DEFAULT (PHY_EDPD_CONFIG_TX_NLP_EN | \
+ PHY_EDPD_CONFIG_TX_NLP_768 | \
+ PHY_EDPD_CONFIG_RX_1_NLP)
/* Mode Control/Status Register */
#define PHY_MODE_CTRL_STS (17)
-#define MODE_CTRL_STS_EDPWRDOWN_ ((u16)0x2000)
-#define MODE_CTRL_STS_ENERGYON_ ((u16)0x0002)
+#define MODE_CTRL_STS_EDPWRDOWN ((u16)0x2000)
+#define MODE_CTRL_STS_ENERGYON ((u16)0x0002)
#define SPECIAL_CTRL_STS (27)
-#define SPECIAL_CTRL_STS_OVRRD_AMDIX_ ((u16)0x8000)
-#define SPECIAL_CTRL_STS_AMDIX_ENABLE_ ((u16)0x4000)
-#define SPECIAL_CTRL_STS_AMDIX_STATE_ ((u16)0x2000)
+#define SPECIAL_CTRL_STS_OVRRD_AMDIX ((u16)0x8000)
+#define SPECIAL_CTRL_STS_AMDIX_ENABLE ((u16)0x4000)
+#define SPECIAL_CTRL_STS_AMDIX_STATE ((u16)0x2000)
#define PHY_INT_SRC (29)
-#define PHY_INT_SRC_ENERGY_ON_ ((u16)0x0080)
-#define PHY_INT_SRC_ANEG_COMP_ ((u16)0x0040)
-#define PHY_INT_SRC_REMOTE_FAULT_ ((u16)0x0020)
-#define PHY_INT_SRC_LINK_DOWN_ ((u16)0x0010)
+#define PHY_INT_SRC_ENERGY_ON ((u16)0x0080)
+#define PHY_INT_SRC_ANEG_COMP ((u16)0x0040)
+#define PHY_INT_SRC_REMOTE_FAULT ((u16)0x0020)
+#define PHY_INT_SRC_LINK_DOWN ((u16)0x0010)
#define PHY_INT_MASK (30)
-#define PHY_INT_MASK_ENERGY_ON_ ((u16)0x0080)
-#define PHY_INT_MASK_ANEG_COMP_ ((u16)0x0040)
-#define PHY_INT_MASK_REMOTE_FAULT_ ((u16)0x0020)
-#define PHY_INT_MASK_LINK_DOWN_ ((u16)0x0010)
-#define PHY_INT_MASK_DEFAULT_ (PHY_INT_MASK_ANEG_COMP_ | \
- PHY_INT_MASK_LINK_DOWN_)
+#define PHY_INT_MASK_ENERGY_ON ((u16)0x0080)
+#define PHY_INT_MASK_ANEG_COMP ((u16)0x0040)
+#define PHY_INT_MASK_REMOTE_FAULT ((u16)0x0020)
+#define PHY_INT_MASK_LINK_DOWN ((u16)0x0010)
+#define PHY_INT_MASK_DEFAULT (PHY_INT_MASK_ANEG_COMP | \
+ PHY_INT_MASK_LINK_DOWN)
#define PHY_SPECIAL (31)
-#define PHY_SPECIAL_SPD_ ((u16)0x001C)
-#define PHY_SPECIAL_SPD_10HALF_ ((u16)0x0004)
-#define PHY_SPECIAL_SPD_10FULL_ ((u16)0x0014)
-#define PHY_SPECIAL_SPD_100HALF_ ((u16)0x0008)
-#define PHY_SPECIAL_SPD_100FULL_ ((u16)0x0018)
+#define PHY_SPECIAL_SPD ((u16)0x001C)
+#define PHY_SPECIAL_SPD_10HALF ((u16)0x0004)
+#define PHY_SPECIAL_SPD_10FULL ((u16)0x0014)
+#define PHY_SPECIAL_SPD_100HALF ((u16)0x0008)
+#define PHY_SPECIAL_SPD_100FULL ((u16)0x0018)
/* USB Vendor Requests */
#define USB_VENDOR_REQUEST_WRITE_REGISTER 0xA0
@@ -287,12 +287,12 @@
#define USB_VENDOR_REQUEST_GET_STATS 0xA2
/* Interrupt Endpoint status word bitfields */
-#define INT_ENP_TX_STOP_ ((u32)BIT(17))
-#define INT_ENP_RX_STOP_ ((u32)BIT(16))
-#define INT_ENP_PHY_INT_ ((u32)BIT(15))
-#define INT_ENP_TXE_ ((u32)BIT(14))
-#define INT_ENP_TDFU_ ((u32)BIT(13))
-#define INT_ENP_TDFO_ ((u32)BIT(12))
-#define INT_ENP_RXDF_ ((u32)BIT(11))
+#define INT_ENP_TX_STOP ((u32)BIT(17))
+#define INT_ENP_RX_STOP ((u32)BIT(16))
+#define INT_ENP_PHY_INT ((u32)BIT(15))
+#define INT_ENP_TXE ((u32)BIT(14))
+#define INT_ENP_TDFU ((u32)BIT(13))
+#define INT_ENP_TDFO ((u32)BIT(12))
+#define INT_ENP_RXDF ((u32)BIT(11))
#endif /* _SMSC95XX_H */
--
2.10.0.rc2.1.g053435c
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
