The TX settings can be calibrated for particular hardware. The phy is reset by Linux, so this cannot be handled by the bootloader. The TRM mentions that the maximum resistance should be used for the DN/DP calibration in order to pass USB certification. The values for the TX registers are poorly described in the TRM. The meanings of the register values were taken from another NXP-provided document: https://community.nxp.com/message/566147#comment-566912 Signed-off-by: Jaret Cantu <jaret.cantu@xxxxxxxxxxx> --- v4. Corrected tx-d-cal register value by rounding up. Changed Freescale web site reference to NXP. v3. Added unit suffix (-ohms) to tx-cal-45-d* v2. Copying devicetree list Removed prettifying extra whitespace Removed unnecessary register rewrite on resume Use min and max constants for clarity .../devicetree/bindings/phy/mxs-usb-phy.txt | 10 ++++ drivers/usb/phy/phy-mxs-usb.c | 61 ++++++++++++++++++++ 2 files changed, 71 insertions(+) diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt index 379b84a..1d25b04 100644 --- a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt @@ -12,6 +12,16 @@ Required properties: - interrupts: Should contain phy interrupt - fsl,anatop: phandle for anatop register, it is only for imx6 SoC series +Optional properties: +- fsl,tx-cal-45-dn-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DN output signal. Default: 45 +- fsl,tx-cal-45-dp-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DP output signal. Default: 45 +- fsl,tx-d-cal: Integer [79-119]. Current trimming value (as a percentage) of + the 17.78mA TX reference current. Default: 100 + Example: usbphy1: usbphy@020c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c index 00bfea0..0e2f1a3 100644 --- a/drivers/usb/phy/phy-mxs-usb.c +++ b/drivers/usb/phy/phy-mxs-usb.c @@ -27,6 +27,7 @@ #define DRIVER_NAME "mxs_phy" #define HW_USBPHY_PWD 0x00 +#define HW_USBPHY_TX 0x10 #define HW_USBPHY_CTRL 0x30 #define HW_USBPHY_CTRL_SET 0x34 #define HW_USBPHY_CTRL_CLR 0x38 @@ -38,6 +39,10 @@ #define HW_USBPHY_IP_SET 0x94 #define HW_USBPHY_IP_CLR 0x98 +#define GM_USBPHY_TX_TXCAL45DP(x) (((x) & 0xf) << 16) +#define GM_USBPHY_TX_TXCAL45DN(x) (((x) & 0xf) << 8) +#define GM_USBPHY_TX_D_CAL(x) (((x) & 0xf) << 0) + #define BM_USBPHY_CTRL_SFTRST BIT(31) #define BM_USBPHY_CTRL_CLKGATE BIT(30) #define BM_USBPHY_CTRL_OTG_ID_VALUE BIT(27) @@ -115,6 +120,12 @@ */ #define MXS_PHY_NEED_IP_FIX BIT(3) +/* Minimum and maximum values for device tree entries */ +#define MXS_PHY_TX_CAL45_MIN 30 +#define MXS_PHY_TX_CAL45_MAX 55 +#define MXS_PHY_TX_D_CAL_MIN 79 +#define MXS_PHY_TX_D_CAL_MAX 119 + struct mxs_phy_data { unsigned int flags; }; @@ -164,6 +175,8 @@ struct mxs_phy { const struct mxs_phy_data *data; struct regmap *regmap_anatop; int port_id; + u32 tx_reg_set; + u32 tx_reg_mask; }; static inline bool is_imx6q_phy(struct mxs_phy *mxs_phy) @@ -185,6 +198,20 @@ static void mxs_phy_clock_switch_delay(void) usleep_range(300, 400); } +static void mxs_phy_tx_init(struct mxs_phy *mxs_phy) +{ + void __iomem *base = mxs_phy->phy.io_priv; + u32 phytx; + + /* Update TX register if there is anything to write */ + if (mxs_phy->tx_reg_mask) { + phytx = readl(base + HW_USBPHY_TX); + phytx &= ~mxs_phy->tx_reg_mask; + phytx |= mxs_phy->tx_reg_set; + writel(phytx, base + HW_USBPHY_TX); + } +} + static int mxs_phy_hw_init(struct mxs_phy *mxs_phy) { int ret; @@ -214,6 +241,8 @@ static int mxs_phy_hw_init(struct mxs_phy *mxs_phy) if (mxs_phy->data->flags & MXS_PHY_NEED_IP_FIX) writel(BM_USBPHY_IP_FIX, base + HW_USBPHY_IP_SET); + mxs_phy_tx_init(mxs_phy); + return 0; } @@ -459,6 +488,7 @@ static int mxs_phy_probe(struct platform_device *pdev) int ret; const struct of_device_id *of_id; struct device_node *np = pdev->dev.of_node; + u32 val; of_id = of_match_device(mxs_phy_dt_ids, &pdev->dev); if (!of_id) @@ -491,6 +521,37 @@ static int mxs_phy_probe(struct platform_device *pdev) } } + /* Precompute which bits of the TX register are to be updated, if any */ + if (!of_property_read_u32(np, "fsl,tx-cal-45-dn-ohms", &val) && + val >= MXS_PHY_TX_CAL45_MIN && val <= MXS_PHY_TX_CAL45_MAX) { + /* Scale to a 4-bit value */ + val = (MXS_PHY_TX_CAL45_MAX - val) * 0xF + / (MXS_PHY_TX_CAL45_MAX - MXS_PHY_TX_CAL45_MIN); + mxs_phy->tx_reg_mask |= GM_USBPHY_TX_TXCAL45DN(~0); + mxs_phy->tx_reg_set |= GM_USBPHY_TX_TXCAL45DN(val); + } + + if (!of_property_read_u32(np, "fsl,tx-cal-45-dp-ohms", &val) && + val >= MXS_PHY_TX_CAL45_MIN && val <= MXS_PHY_TX_CAL45_MAX) { + /* Scale to a 4-bit value. */ + val = (MXS_PHY_TX_CAL45_MAX - val) * 0xF + / (MXS_PHY_TX_CAL45_MAX - MXS_PHY_TX_CAL45_MIN); + mxs_phy->tx_reg_mask |= GM_USBPHY_TX_TXCAL45DP(~0); + mxs_phy->tx_reg_set |= GM_USBPHY_TX_TXCAL45DP(val); + } + + if (!of_property_read_u32(np, "fsl,tx-d-cal", &val) && + val >= MXS_PHY_TX_D_CAL_MIN && val <= MXS_PHY_TX_D_CAL_MAX) { + /* Scale to a 4-bit value. Round up the values and heavily + * weight the rounding by adding 2/3 of the denominator. + */ + val = ((MXS_PHY_TX_D_CAL_MAX - val) * 0xF + + (MXS_PHY_TX_D_CAL_MAX - MXS_PHY_TX_D_CAL_MIN) * 2/3) + / (MXS_PHY_TX_D_CAL_MAX - MXS_PHY_TX_D_CAL_MIN); + mxs_phy->tx_reg_mask |= GM_USBPHY_TX_D_CAL(~0); + mxs_phy->tx_reg_set |= GM_USBPHY_TX_D_CAL(val); + } + ret = of_alias_get_id(np, "usbphy"); if (ret < 0) dev_dbg(&pdev->dev, "failed to get alias id, errno %d\n", ret); -- 1.7.10.4 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
