Dear Heiko,
On 2016/7/17 18:28, Heiko Stübner wrote:
Am Samstag, 16. Juli 2016, 17:57:15 schrieb Rob Herring:
On Thu, Jul 14, 2016 at 04:59:20PM +0800, William Wu wrote:
Add snps,phyif-utmi-width devicetree property to configure
the UTMI+ PHY with an 8- or 16-bit interface. UTMI+ PHY
interface is a hardware property, and it's platform dependent.
Normally,the PHYIF can be configured during coreconsultant.
^
space
But for some specific USB cores(e.g. rk3399 SoC DWC3), the
default PHYIF configuration value is fault, so we need to
reconfigure it by software.
And refer to the DWC3 databook, the GUSB2PHYCFG.USBTRDTIM
must be set to the corresponding value according to the
UTMI+ PHY interface.
Signed-off-by: William Wu <william.wu@xxxxxxxxxxxxxx>
---
Changes in v7:
- remove quirk and use only one property to configure utmi (Heiko, Rob
Herring)
Changes in v6:
- use '-' instead of '_' in dts (Rob Herring)
Changes in v5:
- None
Changes in v4:
- rebase on top of balbi testing/next, remove pdata (balbi)
Changes in v3:
- None
Changes in v2:
- add a quirk for phyif_utmi (balbi)
Documentation/devicetree/bindings/usb/dwc3.txt | 3 +++
drivers/usb/dwc3/core.c | 25
+++++++++++++++++++++++++ drivers/usb/dwc3/core.h
| 10 ++++++++++
3 files changed, 38 insertions(+)
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt
b/Documentation/devicetree/bindings/usb/dwc3.txt index 020b0e9..00cc541
100644
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -47,6 +47,9 @@ Optional properties:
- snps,hird-threshold: HIRD threshold
- snps,hsphy_interface: High-Speed PHY interface selection between
"utmi" for>
UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value
3.
+ - snps,phyif-utmi-width: the value to configure the core to support a
UTMI+ PHY + with an 8- or 16-bit interface. Value 8 select 8-bit
+ interface, value 16 select 16-bit interface.
Is 'phy_type = "utmi_wide"' not the same as 16-bit width?
Again, I think this should be common.
after knowing that I need to look for that "utmi_wide", I think I'd agree.
I found mention of that in usb/ci-hdrc-usb2.txt and usb/fsl-usb.txt and from
the coresponding code, I can see that they really mean the 16bit interface,
the Rockchip TRM as well as the spec [0] seems to call it UTMI+ but really
looks the same as utmi_wide.
Interestingly, there is already generic code in drivers/usb/phy/of.c so that
property should probably move to devicetree/bindings/usb/generic.txt
as well.
Heiko
[0] http://cache.nxp.com/files/corporate/doc/support_info/UTMI-PLUS-SPECIFICATION.pdf
Thank you very much for your kindly help and helpful suggestion.:-D
I quite agree with you about use ‘phy_type’ to config UTMI+ interface
for DWC3 controller, and add the ‘phy_type’ property to
devicetree/bindings/usb/generic.txt.
So I shouldn't add a new dts property ‘snps,phyif-utmi-width’ here， and
just use ‘phy_type’is enough.
BTW, I think rk3399 UTMI+ isn't the same as ‘utmi_wide’. Because UTMI+
support both 8-bit data interface and 16-bit data interface, but refer
to code in drivers/usb/phy/of.c and related driver，‘phy_type =
"utmi_wide"’means 16-bits, 'phy_type = utmi' means 8-bits.
Dear Felipe， how about your opinion about add ‘phy_type’ to config UTMI+
interface?
Best Regards
William wu
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
