The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly. Hook
the phy initialization into the RESET event and the phy power off
into the STOPPED event.
Cc: Peter Chen <peter.chen@xxxxxxx>
Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/usb/chipidea/ci_hdrc_msm.c | 40 +++++++++++++++++++-------------------
drivers/usb/chipidea/core.c | 8 ++++++--
drivers/usb/chipidea/host.c | 8 ++++++--
include/linux/usb/chipidea.h | 2 +-
4 files changed, 33 insertions(+), 25 deletions(-)
diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c
index ab6a7713ee5c..5c486c15e043 100644
--- a/drivers/usb/chipidea/ci_hdrc_msm.c
+++ b/drivers/usb/chipidea/ci_hdrc_msm.c
@@ -75,20 +75,33 @@ static const struct reset_control_ops ci_hdrc_msm_reset_ops = {
.reset = ci_hdrc_msm_por_reset,
};
-static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
+static int ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
{
struct device *dev = ci->dev->parent;
struct ci_hdrc_msm *msm_ci = dev_get_drvdata(dev);
+ int ret;
switch (event) {
case CI_HDRC_CONTROLLER_RESET_EVENT:
dev_dbg(dev, "CI_HDRC_CONTROLLER_RESET_EVENT received\n");
+
+ hw_phymode_configure(ci);
if (msm_ci->secondary_phy) {
u32 val = readl_relaxed(msm_ci->base + HS_PHY_SEC_CTRL);
val |= HS_PHY_DIG_CLAMP_N;
writel_relaxed(val, msm_ci->base + HS_PHY_SEC_CTRL);
}
+ ret = phy_init(ci->phy);
+ if (ret)
+ return ret;
+
+ ret = phy_power_on(ci->phy);
+ if (ret) {
+ phy_exit(ci->phy);
+ return ret;
+ }
+
/* use AHB transactor, allow posted data writes */
hw_write_id_reg(ci, HS_PHY_AHB_MODE, 0xffffffff, 0x8);
@@ -108,21 +121,18 @@ static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
HSPHY_SESS_VLD_CTRL);
}
-
- usb_phy_init(ci->usb_phy);
break;
case CI_HDRC_CONTROLLER_STOPPED_EVENT:
dev_dbg(dev, "CI_HDRC_CONTROLLER_STOPPED_EVENT received\n");
- /*
- * Put the phy in non-driving mode. Otherwise host
- * may not detect soft-disconnection.
- */
- usb_phy_notify_disconnect(ci->usb_phy, USB_SPEED_UNKNOWN);
+ phy_power_off(ci->phy);
+ phy_exit(ci->phy);
break;
default:
dev_dbg(dev, "unknown ci_hdrc event\n");
break;
}
+
+ return 0;
}
static int ci_hdrc_msm_mux_phy(struct ci_hdrc_msm *ci,
@@ -162,7 +172,6 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev)
{
struct ci_hdrc_msm *ci;
struct platform_device *plat_ci;
- struct usb_phy *phy;
struct clk *clk;
struct reset_control *reset;
struct resource *res;
@@ -176,21 +185,12 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev)
return -ENOMEM;
platform_set_drvdata(pdev, ci);
- /*
- * OTG(PHY) driver takes care of PHY initialization, clock management,
- * powering up VBUS, mapping of registers address space and power
- * management.
- */
- phy = devm_usb_get_phy_by_phandle(&pdev->dev, "usb-phy", 0);
- if (IS_ERR(phy))
- return PTR_ERR(phy);
-
ci->pdata.name = "ci_hdrc_msm";
ci->pdata.capoffset = DEF_CAPOFFSET;
ci->pdata.flags = CI_HDRC_REGS_SHARED | CI_HDRC_DISABLE_STREAMING |
- CI_HDRC_OVERRIDE_AHB_BURST;
+ CI_HDRC_OVERRIDE_AHB_BURST |
+ CI_HDRC_OVERRIDE_PHY_CONTROL;
ci->pdata.notify_event = ci_hdrc_msm_notify_event;
- ci->pdata.usb_phy = phy;
reset = devm_reset_control_get(&pdev->dev, "core");
if (IS_ERR(reset))
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index f144e1bbcc82..0866c03d66df 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -327,6 +327,7 @@ void hw_phymode_configure(struct ci_hdrc *ci)
hw_write(ci, OP_PORTSC, PORTSC_STS, PORTSC_STS);
}
}
+EXPORT_SYMBOL_GPL(hw_phymode_configure);
/**
* _ci_usb_phy_init: initialize phy taking in account both phy and usb_phy
@@ -503,9 +504,12 @@ int hw_device_reset(struct ci_hdrc *ci)
return ret;
}
- if (ci->platdata->notify_event)
- ci->platdata->notify_event(ci,
+ if (ci->platdata->notify_event) {
+ ret = ci->platdata->notify_event(ci,
CI_HDRC_CONTROLLER_RESET_EVENT);
+ if (ret)
+ return ret;
+ }
/* USBMODE should be configured step by step */
hw_write(ci, OP_USBMODE, USBMODE_CM, USBMODE_CM_IDLE);
diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
index a1d8551ca79d..844be1d02d38 100644
--- a/drivers/usb/chipidea/host.c
+++ b/drivers/usb/chipidea/host.c
@@ -87,8 +87,12 @@ static int ehci_ci_reset(struct usb_hcd *hcd)
if (ret)
return ret;
- if (ci->platdata->notify_event)
- ci->platdata->notify_event(ci, CI_HDRC_CONTROLLER_RESET_EVENT);
+ if (ci->platdata->notify_event) {
+ ret = ci->platdata->notify_event(ci,
+ CI_HDRC_CONTROLLER_RESET_EVENT);
+ if (ret)
+ return ret;
+ }
ci_platform_configure(ci);
diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
index d07b162073f7..5e76552c81e9 100644
--- a/include/linux/usb/chipidea.h
+++ b/include/linux/usb/chipidea.h
@@ -61,7 +61,7 @@ struct ci_hdrc_platform_data {
enum usb_dr_mode dr_mode;
#define CI_HDRC_CONTROLLER_RESET_EVENT 0
#define CI_HDRC_CONTROLLER_STOPPED_EVENT 1
- void (*notify_event) (struct ci_hdrc *ci, unsigned event);
+ int (*notify_event) (struct ci_hdrc *ci, unsigned event);
struct regulator *reg_vbus;
struct usb_otg_caps ci_otg_caps;
bool tpl_support;
--
2.9.0.rc2.8.ga28705d
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
