add a DT binding doc for MediaTek USB3 DRD driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
---
.../devicetree/bindings/usb/mt8173-mtu3.txt | 86 ++++++++++++++++++++
1 file changed, 86 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
new file mode 100644
index 0000000..12f3c2a
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
@@ -0,0 +1,86 @@
+The device node for Mediatek USB3.0 DRD controller
+
+Required properties:
+ - compatible : should be "mediatek,mt8173-mtu3"
+ - reg : specifies physical base address and size of the registers
+ - reg-names: should be "mac" for device IP and "ippc" for IP port control
+ - interrupts : interrupt used by the device IP
+ - power-domains : a phandle to USB power domain node to control USB's
+ mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+ - clock-names : must contain "sys_ck" for clock of controller;
+ "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
+ depends on "mediatek,enable-wakeup"
+ - phys : a list of phandle + phy specifier pairs
+ - dr_mode : should be one of "host", "peripheral" or "otg",
+ refer to usb/generic.txt
+
+Optional properties:
+ - #address-cells, #size-cells : should be '2' if the device has sub-nodes
+ with 'reg' property
+ - ranges : allows valid 1:1 translation between child's address space and
+ parent's address space
+ - extcon : external connector for vbus and idpin changes detection, needed
+ when supports dual-role mode.
+ - vbus-supply : reference to the VBUS regulator, needed when supports
+ dual-role mode.
+ - pinctl-names : a pinctrl state named "default" must be defined,
+ "id_float" and "id_ground" are optinal which depends on
+ "mediatek,enable-manual-drd"
+ - pinctrl-0 : pin control group
+ See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+
+ - maximum-speed : valid arguments are "super-speed", "high-speed" and
+ "full-speed"; refer to usb/generic.txt
+ - enable-manual-drd : supports manual dual-role switch via debugfs; usually
+ used when receptacle is TYPE-A and also wants to support dual-role
+ mode.
+ - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+ control register, it depends on "mediatek,enable-wakeup".
+
+Sub-nodes:
+The xhci should be added as subnode to mtu3 as shown in the following example
+if host mode is enabled. The DT binding details of xhci can be found in:
+Documentation/devicetree/bindings/usb/mt8173-xhci.txt
+
+Example:
+ssusb: usb@11271000 {
+ compatible = "mediatek,mt8173-mtu3";
+ reg = <0 0x11271000 0 0x3000>,
+ <0 0x11280700 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&phy_port0 PHY_TYPE_USB3>,
+ <&phy_port1 PHY_TYPE_USB2>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>,
+ <&pericfg CLK_PERI_USB0>,
+ <&pericfg CLK_PERI_USB1>;
+ clock-names = "sys_ck",
+ "wakeup_deb_p0",
+ "wakeup_deb_p1";
+ vusb33-supply = <&mt6397_vusb_reg>;
+ vbus-supply = <&usb_p0_vbus>;
+ extcon = <&extcon_usb>;
+ dr_mode = "otg";
+ mediatek,enable-wakeup;
+ mediatek,syscon-wakeup = <&pericfg>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usb_host: xhci@11270000 {
+ compatible = "mediatek,mt8173-xhci";
+ reg = <0 0x11270000 0 0x1000>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>;
+ clock-names = "sys_ck";
+ vusb33-supply = <&mt6397_vusb_reg>;
+ status = "disabled";
+ };
+};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
