Hi, whilst, as Dave Higton pointed out, that Voltage is within spec, it is possible that your CDC device is not. Have you measured the current drawn on your three machines? It would be interesting to see if an externally powered USB hub makes a difference. Tony Olech On Wed, 2009-01-21 at 21:17 +0100, Wim de Vries wrote: > OK. Thanks. > I have measured the voltage, with the device connected: > on my (Win) PC 5.10 V > on my (Linux) laptop: 5.12V > on the asus eee pc: 4.96V > Do you think that difference is a problem? > regards, > Wim > > Hi, > > It is not safe. Whilst we have done that sort of thing successfully, > > we have also blown up bits of hardware as well. Even if you use a > > Y-cable (one power-only connector and one data+power) we have had > > mixed results unless both Y-cable plugs are inserted into the same > > machine - our h/w engineers mutter something about earth loops. > > > > Could use a meter to measure how much current is being consumed > > when your CDC device is plugged into the HP and into the ASUS? > > Measure the voltage whilst you are at it - we have seen some USB > > host controllers supplying 3.3V which works for a lot of USB Memory > > Sticks but not all of them. > > > > It could well be just a faulty ASUS as Alan Stern suggested. > > > > Tony Olech > > > > > > On Wed, 2009-01-21 at 15:39 +0100, Wim de Vries wrote: > > > > > > from your log as well as the failing USB CDC modem you have: > > > > > > > > idVendor=0951 idProduct=1606 ENE UB6225 - SD card reader > > > > idVendor=05e3 idProduct=0505 USB Camera > > > > idVendor=093a idProduct=2510 USB OPTICAL MOUSE > > > > > > > > my experience with developing f/w to support CDC modems is that > > > > they need a lot of current. I assume that the modem works OK on > > > > your HP machine and that you can plug in a memory stick OK on the > > > > asus in the same port that you tried to plug the modem into? > > > > Tony Olech > > > > > > > Thanks. > > > It is not a modem, but a device with some meteo sensors with serial > > > communication. > > > The SD card reader and camera are build in. > > > I have tried other devices (including a gps mouse, also using CDC; > > > acceleration sensor, SD cards) and they work fine. > > > > > > Would it be save to supply 5 V (from an external source) to the correct > > > (USB) wires just to test it? > > > > > > regards, > > > wim > > > > > > > > > > > > > On Tue, 2009-01-20 at 21:14 +0100, Wim de Vries wrote: > > > > > > > > > Thanks for the reply. > > > > > Just this device and a mouse. Even with the mouse disconnected I have > > > > > the same problem. > > > > > I don't have an externally powered USB hub. The system should work > > > > > without (external) power :( > > > > > I'll try to borrow one somewhere, just to test it. > > > > > > > > > > regards, > > > > > W > > > > > im > > > > > Tony Olech wrote: > > > > > > > > > > > Hi, > > > > > > > > > > > > you seem to have a few USB devices connected, have you > > > > > > tried using an externally powered USB HUB? > > > > > > > > > > > > Tony Olech > > > > > > Elan Digital Systems > > > > > > > > > > > > On Tue, 2009-01-20 at 17:25 +0100, Wim de Vries wrote: > > > > > > > > > > > > > > > > > > > Hi, > > > > > > > I am trying to connect an USB device to my asus eee pc. > > > > > > > The device connects OK on my HP compaq 6910p with Suse 10.3: > > > > > > > dmesg: > > > > > > > usb 7-1: new full speed USB device using uhci_hcd and address 4 > > > > > > > usb 7-1: new device found, idVendor=04d8, idProduct=000a > > > > > > > usb 7-1: new device strings: Mfr=1, Product=2, SerialNumber=3 > > > > > > > usb 7-1: Product: PIC18 USB CDC > > > > > > > usb 7-1: Manufacturer: Microchip > > > > > > > usb 7-1: SerialNumber: V1.1FS > > > > > > > usb 7-1: configuration #1 chosen from 1 choice > > > > > > > drivers/usb/class/cdc-acm.c: This device cannot do calls on its own. > > > > > > > > > > > > It > > > > > > > > > > > > is no; modem. > > > > > > > cdc_acm 7-1:1.0: ttyACM0: USB ACM device > > > > > > > > > > > > > > So it should ánd can use cdc-acm. > > > > > > > > > > > > > > Nevertheless, on the asus (kernel version: 2.6.26-1-686, Debian,KDE): > > > > > > > > > > > > > > dmesg: > > > > > > > [ 0.000000] Initializing cgroup subsys cpuset > > > > > > > [ 0.000000] Initializing cgroup subsys cpu > > > > > > > [ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-11) > > > > > > > (waldi@xxxxxxxxxx) (gcc version 4.1.3 20080623 (prerelease) (Debian > > > > > > > 4.1.2-23)) #1 SMP Wed Nov 26 19:14:11 UTC 2008 > > > > > > > [ 0.000000] BIOS-provided physical RAM map: > > > > > > > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 > > > > > > > > > > > > (usable) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 > > > > > > > > > > > > (reserved) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 > > > > > > > > > > > > (reserved) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f780000 > > > > > > > > > > > > (usable) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 000000003f780000 - 000000003f790000 (ACPI > > > > > > > > > > > > data) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 000000003f790000 - 000000003f7d0000 (ACPI > > > > > > > > > > > > NVS) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 000000003f7d0000 - 000000003f7de000 > > > > > > > > > > > > (reserved) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 000000003f7e0000 - 000000003f800000 > > > > > > > > > > > > (reserved) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 > > > > > > > > > > > > (reserved) > > > > > > > > > > > > [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 > > > > > > > > > > > > (reserved) > > > > > > > > > > > > [ 0.000000] 119MB HIGHMEM available. > > > > > > > [ 0.000000] 896MB LOWMEM available. > > > > > > > [ 0.000000] found SMP MP-table at [c00ff780] 000ff780 > > > > > > > [ 0.000000] Entering add_active_range(0, 0, 259968) 0 entries of > > > > > > > > > > > > 256 used > > > > > > > > > > > > [ 0.000000] Zone PFN ranges: > > > > > > > [ 0.000000] DMA 0 -> 4096 > > > > > > > [ 0.000000] Normal 4096 -> 229376 > > > > > > > [ 0.000000] HighMem 229376 -> 259968 > > > > > > > [ 0.000000] Movable zone start PFN for each node > > > > > > > [ 0.000000] early_node_map[1] active PFN ranges > > > > > > > [ 0.000000] 0: 0 -> 259968 > > > > > > > [ 0.000000] On node 0 totalpages: 259968 > > > > > > > [ 0.000000] DMA zone: 32 pages used for memmap > > > > > > > [ 0.000000] DMA zone: 0 pages reserved > > > > > > > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > > > > > > > [ 0.000000] Normal zone: 1760 pages used for memmap > > > > > > > [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 > > > > > > > [ 0.000000] HighMem zone: 239 pages used for memmap > > > > > > > [ 0.000000] HighMem zone: 30353 pages, LIFO batch:7 > > > > > > > [ 0.000000] Movable zone: 0 pages used for memmap > > > > > > > [ 0.000000] DMI present. > > > > > > > [ 0.000000] ACPI: RSDP 000FBE60, 0014 (r0 ACPIAM) > > > > > > > [ 0.000000] ACPI: RSDT 3F780000, 0034 (r1 A M I OEMRSDT 9000811 > > > > > > > > > > > > MSFT > > > > > > > > > > > > 97) > > > > > > > [ 0.000000] ACPI: FACP 3F780200, 0081 (r1 A M I OEMFACP 9000811 > > > > > > > > > > > > MSFT > > > > > > > > > > > > 97) > > > > > > > [ 0.000000] ACPI: DSDT 3F780400, 6109 (r1 A0979 A0979034 34 > > > > > > > > > > > > INTL > > > > > > > > > > > > 20060113) > > > > > > > [ 0.000000] ACPI: FACS 3F790000, 0040 > > > > > > > [ 0.000000] ACPI: APIC 3F780390, 0068 (r1 A M I OEMAPIC 9000811 > > > > > > > > > > > > MSFT > > > > > > > > > > > > 97) > > > > > > > [ 0.000000] ACPI: OEMB 3F790040, 0046 (r1 A M I AMI_OEM 9000811 > > > > > > > > > > > > MSFT > > > > > > > > > > > > 97) > > > > > > > [ 0.000000] ACPI: MCFG 3F786510, 003C (r1 A M I OEMMCFG 9000811 > > > > > > > > > > > > MSFT > > > > > > > > > > > > 97) > > > > > > > [ 0.000000] ACPI: PM-Timer IO Port: 0x808 > > > > > > > [ 0.000000] ACPI: Local APIC address 0xfee00000 > > > > > > > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > > > > > > > [ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option. > > > > > > > [ 0.000000] Using ACPI for processor (LAPIC) configuration > > > > > > > > > > > > information > > > > > > > > > > > > [ 0.000000] Intel MultiProcessor Specification v1.4 > > > > > > > [ 0.000000] Virtual Wire compatibility mode. > > > > > > > [ 0.000000] MPTABLE: OEM ID: INTEL Product ID: <6>MPTABLE: > > > > > > > > > > > > Product > > > > > > > > > > > > ID: <6>MPTABLE: APIC at: 0xFEE00000 > > > > > > > [ 0.000000] I/O APIC #1 Version 32 at 0xFEC00000. > > > > > > > [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs > > > > > > > [ 0.000000] Processors: 1 > > > > > > > [ 0.000000] Allocating PCI resources starting at 40000000 (gap: > > > > > > > 3f800000:bf600000) > > > > > > > [ 0.000000] PM: Registered nosave memory: 000000000009f000 - > > > > > > > 00000000000a0000 > > > > > > > [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - > > > > > > > 00000000000e4000 > > > > > > > [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - > > > > > > > 0000000000100000 > > > > > > > [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs > > > > > > > [ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data > > > > > > > [ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1 > > > > > > > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > > > > > > > Total pages: 257937 > > > > > > > [ 0.000000] Kernel command line: root=/dev/sdb1 ro quiet noapic > > > > > > > [ 0.000000] mapped APIC to ffffb000 (fee00000) > > > > > > > [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) > > > > > > > [ 0.000000] Enabling fast FPU save and restore... done. > > > > > > > [ 0.000000] Enabling unmasked SIMD FPU exception support... done. > > > > > > > [ 0.000000] Initializing CPU#0 > > > > > > > [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) > > > > > > > [ 0.000000] Detected 900.130 MHz processor. > > > > > > > [ 0.004000] Console: colour VGA+ 80x25 > > > > > > > [ 0.004000] console [tty0] enabled > > > > > > > [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, > > > > > > > > > > > > 524288 > > > > > > > > > > > > bytes) > > > > > > > [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, > > > > > > > > > > > > 262144 bytes) > > > > > > > > > > > > [ 0.004000] Memory: 1021104k/1039872k available (1768k kernel > > > > > > > > > > > > code, > > > > > > > > > > > > 18032k reserved, 752k data, 244k init, 122368k highmem) > > > > > > > [ 0.004000] virtual kernel memory layout: > > > > > > > [ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB) > > > > > > > [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) > > > > > > > [ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) > > > > > > > [ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) > > > > > > > [ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB) > > > > > > > [ 0.004000] .data : 0xc02ba293 - 0xc0376620 ( 752 kB) > > > > > > > [ 0.004000] .text : 0xc0100000 - 0xc02ba293 (1768 kB) > > > > > > > [ 0.004000] Checking if this processor honours the WP bit even in > > > > > > > supervisor mode...Ok. > > > > > > > [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated > > > > > > > [ 0.084214] Calibrating delay using timer specific routine.. > > > > > > > > > > > > 1802.45 > > > > > > > > > > > > BogoMIPS (lpj=3604919) > > > > > > > [ 0.084287] Security Framework initialized > > > > > > > [ 0.084298] SELinux: Disabled at boot. > > > > > > > [ 0.084308] Capability LSM initialized > > > > > > > [ 0.084334] Mount-cache hash table entries: 512 > > > > > > > [ 0.084609] Initializing cgroup subsys ns > > > > > > > [ 0.084617] Initializing cgroup subsys cpuacct > > > > > > > [ 0.084622] Initializing cgroup subsys devices > > > > > > > [ 0.084660] CPU: L1 I cache: 32K, L1 D cache: 32K > > > > > > > [ 0.084666] CPU: L2 cache: 512K > > > > > > > [ 0.084674] Intel machine check architecture supported. > > > > > > > [ 0.084682] Intel machine check reporting enabled on CPU#0. > > > > > > > [ 0.084705] Checking 'hlt' instruction... OK. > > > > > > > [ 0.100731] SMP alternatives: switching to UP code > > > > > > > [ 0.110392] Freeing SMP alternatives: 16k freed > > > > > > > [ 0.110398] ACPI: Core revision 20080321 > > > > > > > [ 0.124464] ACPI: setting ELCR to 0200 (from 0ca8) > > > > > > > [ 0.132008] CPU0: Intel(R) Celeron(R) M processor 900MHz > > > > > > > stepping 08 > > > > > > > [ 0.132008] APIC calibration not consistent with PM Timer: 136ms > > > > > > > instead of 100ms > > > > > > > [ 0.132008] APIC delta adjusted to PM-Timer: 625063 (850136) > > > > > > > [ 0.132008] Brought up 1 CPUs > > > > > > > [ 0.132008] Total of 1 processors activated (1802.45 BogoMIPS). > > > > > > > [ 0.132008] CPU0 attaching sched-domain: > > > > > > > [ 0.132008] domain 0: span 0 > > > > > > > [ 0.132008] groups: 0 > > > > > > > [ 0.132008] net_namespace: 660 bytes > > > > > > > [ 0.132008] Booting paravirtualized kernel on bare hardware > > > > > > > [ 0.132008] NET: Registered protocol family 16 > > > > > > > [ 0.132008] ACPI: bus type pci registered > > > > > > > [ 0.132008] PCI: MCFG configuration 0: base e0000000 segment 0 > > > > > > > > > > > > buses 0 > > > > > > > > > > > > - 255 > > > > > > > [ 0.132008] PCI: Not using MMCONFIG. > > > > > > > [ 0.132008] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last > > > > > > > > > > > > bus=5 > > > > > > > > > > > > [ 0.132008] PCI: Using configuration type 1 for base access > > > > > > > [ 0.132008] Setting up standard PCI resources > > > > > > > [ 0.144009] ACPI: EC: Look up EC in DSDT > > > > > > > [ 0.159346] ACPI: Interpreter enabled > > > > > > > [ 0.159352] ACPI: (supports S0 S1 S3 S4 S5) > > > > > > > [ 0.159388] ACPI: Using PIC for interrupt routing > > > > > > > [ 0.159511] PCI: MCFG configuration 0: base e0000000 segment 0 > > > > > > > > > > > > buses 0 > > > > > > > > > > > > - 255 > > > > > > > [ 0.162710] PCI: MCFG area at e0000000 reserved in ACPI > > > > > > > > > > > > motherboard > > > > > > > > > > > > resources > > > > > > > [ 0.162716] PCI: Using MMCONFIG for extended config space > > > > > > > [ 0.173511] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data > > > > > > > > > > > > = 0x62 > > > > > > > > > > > > [ 0.173518] ACPI: EC: driver started in poll mode > > > > > > > [ 0.173755] ACPI: PCI Root Bridge [PCI0] (0000:00) > > > > > > > [ 0.174621] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 > > > > > > > [ 0.174633] pci 0000:00:1f.0: quirk: region 0800-087f claimed by > > > > > > > > > > > > ICH6 > > > > > > > > > > > > ACPI/GPIO/TCO > > > > > > > [ 0.174640] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by > > > > > > > > > > > > ICH6 GPIO > > > > > > > > > > > > [ 0.175178] PCI: Transparent bridge - 0000:00:1e.0 > > > > > > > [ 0.175222] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > > > > > > > [ 0.175798] ACPI: PCI Interrupt Routing Table > > > > > > > > > > > > [\_SB_.PCI0.P0P3._PRT] > > > > > > > > > > > > [ 0.175995] ACPI: PCI Interrupt Routing Table > > > > > > > > > > > > [\_SB_.PCI0.P0P5._PRT] > > > > > > > > > > > > [ 0.176243] ACPI: PCI Interrupt Routing Table > > > > > > > > > > > > [\_SB_.PCI0.P0P6._PRT] > > > > > > > > > > > > [ 0.184710] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 > > > > > > > > > > > > 12 > > > > > > > > > > > > 14 15) > > > > > > > [ 0.184978] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 > > > > > > > > > > > > 12 > > > > > > > > > > > > 14 15) > > > > > > > [ 0.185241] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 > > > > > > > > > > > > 12 > > > > > > > > > > > > 14 15) > > > > > > > [ 0.185500] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 > > > > > > > > > > > > 12 > > > > > > > > > > > > 14 15) > > > > > > > [ 0.185763] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 > > > > > > > > > > > > 12 14 > > > > > > > > > > > > 15) *0, disabled. > > > > > > > [ 0.186025] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 > > > > > > > > > > > > 12 14 > > > > > > > > > > > > 15) *0, disabled. > > > > > > > [ 0.186287] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 > > > > > > > > > > > > 12 14 > > > > > > > > > > > > 15) *0, disabled. > > > > > > > [ 0.186548] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 > > > > > > > > > > > > 12 > > > > > > > > > > > > 14 15) > > > > > > > [ 0.186882] Linux Plug and Play Support v0.97 (c) Adam Belay > > > > > > > [ 0.186950] pnp: PnP ACPI init > > > > > > > [ 0.186965] ACPI: bus type pnp registered > > > > > > > [ 0.191275] pnp: PnP ACPI: found 13 devices > > > > > > > [ 0.191282] ACPI: ACPI bus type pnp unregistered > > > > > > > [ 0.191292] PnPBIOS: Disabled by ACPI PNP > > > > > > > [ 0.191792] PCI: Using ACPI for IRQ routing > > > > > > > [ 0.192357] hpet clockevent registered > > > > > > > [ 0.192369] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 > > > > > > > [ 0.192377] hpet0: 3 64-bit timers, 14318180 Hz > > > > > > > [ 0.193456] ACPI: RTC can wake from S4 > > > > > > > [ 0.193513] system 00:01: iomem range 0xfed13000-0xfed19fff has > > > > > > > > > > > > been > > > > > > > > > > > > reserved > > > > > > > [ 0.193534] system 00:08: ioport range 0x380-0x383 has been > > > > > > > > > > > > reserved > > > > > > > > > > > > [ 0.193540] system 00:08: ioport range 0x4d0-0x4d1 has been > > > > > > > > > > > > reserved > > > > > > > > > > > > [ 0.193546] system 00:08: ioport range 0x800-0x87f has been > > > > > > > > > > > > reserved > > > > > > > > > > > > [ 0.193552] system 00:08: ioport range 0x480-0x4bf has been > > > > > > > > > > > > reserved > > > > > > > > > > > > [ 0.193559] system 00:08: iomem range 0xfed1c000-0xfed1ffff has > > > > > > > > > > > > been > > > > > > > > > > > > reserved > > > > > > > [ 0.193565] system 00:08: iomem range 0xfed20000-0xfed8ffff has > > > > > > > > > > > > been > > > > > > > > > > > > reserved > > > > > > > [ 0.193572] system 00:08: iomem range 0xfff00000-0xffffffff could > > > > > > > > > > > > not > > > > > > > > > > > > be reserved > > > > > > > [ 0.193584] system 00:09: iomem range 0xfec00000-0xfec00fff has > > > > > > > > > > > > been > > > > > > > > > > > > reserved > > > > > > > [ 0.193590] system 00:09: iomem range 0xfee00000-0xfee00fff could > > > > > > > > > > > > not > > > > > > > > > > > > be reserved > > > > > > > [ 0.193602] system 00:0a: iomem range 0xe0000000-0xefffffff has > > > > > > > > > > > > been > > > > > > > > > > > > reserved > > > > > > > [ 0.193614] system 00:0b: iomem range 0xe0000000-0xefffffff has > > > > > > > > > > > > been > > > > > > > > > > > > reserved > > > > > > > [ 0.193631] system 00:0c: iomem range 0x0-0x9ffff could not be > > > > > > > > > > > > reserved > > > > > > > > > > > > [ 0.193638] system 00:0c: iomem range 0xe0000-0xfffff could not be > > > > > > > reserved > > > > > > > [ 0.193644] system 00:0c: iomem range 0x100000-0x3f7fffff could > > > > > > > > > > > > not be > > > > > > > > > > > > reserved > > > > > > > [ 0.224415] PCI: Bridge: 0000:00:1c.0 > > > > > > > [ 0.224420] IO window: disabled. > > > > > > > [ 0.224427] MEM window: disabled. > > > > > > > [ 0.224433] PREFETCH window: disabled. > > > > > > > [ 0.224441] PCI: Bridge: 0000:00:1c.1 > > > > > > > [ 0.224444] IO window: disabled. > > > > > > > [ 0.224451] MEM window: 0xfbf00000-0xfbffffff > > > > > > > [ 0.224457] PREFETCH window: disabled. > > > > > > > [ 0.224465] PCI: Bridge: 0000:00:1c.2 > > > > > > > [ 0.224468] IO window: disabled. > > > > > > > [ 0.224475] MEM window: 0xf8000000-0xfbefffff > > > > > > > [ 0.224482] PREFETCH window: > > > > > > > > > > > > 0x00000000f0000000-0x00000000f6ffffff > > > > > > > > > > > > [ 0.224491] PCI: Bridge: 0000:00:1e.0 > > > > > > > [ 0.224494] IO window: disabled. > > > > > > > [ 0.224500] MEM window: disabled. > > > > > > > [ 0.224505] PREFETCH window: disabled. > > > > > > > [ 0.224872] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5 > > > > > > > [ 0.224878] PCI: setting IRQ 5 as level-triggered > > > > > > > [ 0.224884] ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> > > > > > > > > > > > > GSI 5 > > > > > > > > > > > > (level, low) -> IRQ 5 > > > > > > > [ 0.224896] PCI: Setting latency timer of device 0000:00:1c.0 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 0.225204] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 > > > > > > > [ 0.225209] PCI: setting IRQ 11 as level-triggered > > > > > > > [ 0.225215] ACPI: PCI Interrupt 0000:00:1c.1[B] -> Link [LNKB] -> > > > > > > > > > > > > GSI > > > > > > > > > > > > 11 (level, low) -> IRQ 11 > > > > > > > [ 0.225226] PCI: Setting latency timer of device 0000:00:1c.1 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 0.225528] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 > > > > > > > [ 0.225533] PCI: setting IRQ 10 as level-triggered > > > > > > > [ 0.225539] ACPI: PCI Interrupt 0000:00:1c.2[C] -> Link [LNKC] -> > > > > > > > > > > > > GSI > > > > > > > > > > > > 10 (level, low) -> IRQ 10 > > > > > > > [ 0.225549] PCI: Setting latency timer of device 0000:00:1c.2 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 0.225564] PCI: Setting latency timer of device 0000:00:1e.0 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 0.225608] NET: Registered protocol family 2 > > > > > > > [ 0.225794] IP route cache hash table entries: 32768 (order: 5, > > > > > > > > > > > > 131072 > > > > > > > > > > > > bytes) > > > > > > > [ 0.226219] TCP established hash table entries: 131072 (order: 8, > > > > > > > 1048576 bytes) > > > > > > > [ 0.227867] TCP bind hash table entries: 65536 (order: 7, 524288 > > > > > > > > > > > > bytes) > > > > > > > > > > > > [ 0.228708] TCP: Hash tables configured (established 131072 bind > > > > > > > > > > > > 65536) > > > > > > > > > > > > [ 0.228716] TCP reno registered > > > > > > > [ 0.228952] NET: Registered protocol family 1 > > > > > > > [ 0.229175] checking if image is initramfs...<7>Switched to high > > > > > > > resolution mode on CPU 0 > > > > > > > [ 0.718795] it is > > > > > > > [ 1.253276] Freeing initrd memory: 5802k freed > > > > > > > [ 1.254324] audit: initializing netlink socket (disabled) > > > > > > > [ 1.254352] type=2000 audit(1232394730.252:1): initialized > > > > > > > [ 1.254614] highmem bounce pool size: 64 pages > > > > > > > [ 1.254625] Total HugeTLB memory allocated, 0 > > > > > > > [ 1.254763] VFS: Disk quotas dquot_6.5.1 > > > > > > > [ 1.254815] Dquot-cache hash table entries: 1024 (order 0, 4096 > > > > > > > > > > > > bytes) > > > > > > > > > > > > [ 1.254881] msgmni has been set to 1767 > > > > > > > [ 1.255090] Block layer SCSI generic (bsg) driver version 0.4 > > > > > > > > > > > > loaded > > > > > > > > > > > > (major 253) > > > > > > > [ 1.255096] io scheduler noop registered > > > > > > > [ 1.255101] io scheduler anticipatory registered > > > > > > > [ 1.255105] io scheduler deadline registered > > > > > > > [ 1.255130] io scheduler cfq registered (default) > > > > > > > [ 1.255155] pci 0000:00:02.0: Boot video device > > > > > > > [ 1.255428] PCI: Setting latency timer of device 0000:00:1c.0 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 1.255470] assign_interrupt_mode Found MSI capability > > > > > > > [ 1.255513] Allocate Port Service[0000:00:1c.0:pcie00] > > > > > > > [ 1.255593] Allocate Port Service[0000:00:1c.0:pcie02] > > > > > > > [ 1.255663] Allocate Port Service[0000:00:1c.0:pcie03] > > > > > > > [ 1.255788] PCI: Setting latency timer of device 0000:00:1c.1 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 1.255827] assign_interrupt_mode Found MSI capability > > > > > > > [ 1.255867] Allocate Port Service[0000:00:1c.1:pcie00] > > > > > > > [ 1.255942] Allocate Port Service[0000:00:1c.1:pcie02] > > > > > > > [ 1.256010] Allocate Port Service[0000:00:1c.1:pcie03] > > > > > > > [ 1.256157] PCI: Setting latency timer of device 0000:00:1c.2 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 1.256198] assign_interrupt_mode Found MSI capability > > > > > > > [ 1.256237] Allocate Port Service[0000:00:1c.2:pcie00] > > > > > > > [ 1.256310] Allocate Port Service[0000:00:1c.2:pcie02] > > > > > > > [ 1.256379] Allocate Port Service[0000:00:1c.2:pcie03] > > > > > > > [ 1.256929] isapnp: Scanning for PnP cards... > > > > > > > [ 1.610708] isapnp: No Plug & Play device found > > > > > > > [ 1.615603] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, > > > > > > > > > > > > IRQ > > > > > > > > > > > > sharing enabled > > > > > > > [ 1.619389] brd: module loaded > > > > > > > [ 1.619573] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at > > > > > > > 0x60,0x64 irq 1,12 > > > > > > > [ 1.654990] serio: i8042 KBD port at 0x60,0x64 irq 1 > > > > > > > [ 1.655000] serio: i8042 AUX port at 0x60,0x64 irq 12 > > > > > > > [ 1.655304] mice: PS/2 mouse device common for all mice > > > > > > > [ 1.656447] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 > > > > > > > [ 1.656447] rtc0: alarms up to one month > > > > > > > [ 1.656447] cpuidle: using governor ladder > > > > > > > [ 1.656447] cpuidle: using governor menu > > > > > > > [ 1.656447] No iBFT detected. > > > > > > > [ 1.656447] TCP cubic registered > > > > > > > [ 1.656447] NET: Registered protocol family 17 > > > > > > > [ 1.656447] Using IPI No-Shortcut mode > > > > > > > [ 1.656447] registered taskstats version 1 > > > > > > > [ 1.656447] rtc_cmos 00:03: setting system clock to 2009-01-19 > > > > > > > > > > > > 19:52:11 > > > > > > > > > > > > UTC (1232394731) > > > > > > > [ 1.656447] Freeing unused kernel memory: 244k freed > > > > > > > [ 1.679754] input: AT Translated Set 2 keyboard as > > > > > > > > > > > > /class/input/input0 > > > > > > > > > > > > [ 1.830264] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > > > > > > > [ 1.830360] ACPI: ACPI0007:00 is registered as cooling_device0 > > > > > > > [ 1.830368] ACPI: Processor [CPU1] (supports 8 throttling states) > > > > > > > [ 1.834937] ACPI: EC: non-query interrupt received, switching to > > > > > > > interrupt mode > > > > > > > [ 1.835020] Marking TSC unstable due to: TSC halts in idle. > > > > > > > [ 2.023282] ACPI: LNXTHERM:01 is registered as thermal_zone0 > > > > > > > [ 2.030790] ACPI: Thermal Zone [TZ00] (62 C) > > > > > > > [ 2.192033] Clocksource tsc unstable (delta = -195791138 ns) > > > > > > > [ 3.165517] usbcore: registered new interface driver usbfs > > > > > > > [ 3.165566] usbcore: registered new interface driver hub > > > > > > > [ 3.165634] usbcore: registered new device driver usb > > > > > > > [ 3.178277] USB Universal Host Controller Interface driver v3.0 > > > > > > > [ 3.178707] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3 > > > > > > > [ 3.178713] PCI: setting IRQ 3 as level-triggered > > > > > > > [ 3.178720] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> > > > > > > > > > > > > GSI 3 > > > > > > > > > > > > (level, low) -> IRQ 3 > > > > > > > [ 3.178736] PCI: Setting latency timer of device 0000:00:1d.0 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 3.178745] uhci_hcd 0000:00:1d.0: UHCI Host Controller > > > > > > > [ 3.178937] uhci_hcd 0000:00:1d.0: new USB bus registered, > > > > > > > > > > > > assigned bus > > > > > > > > > > > > number 1 > > > > > > > [ 3.178974] uhci_hcd 0000:00:1d.0: irq 3, io base 0x0000e400 > > > > > > > [ 3.179123] usb usb1: configuration #1 chosen from 1 choice > > > > > > > [ 3.179176] hub 1-0:1.0: USB hub found > > > > > > > [ 3.179188] hub 1-0:1.0: 2 ports detected > > > > > > > [ 3.280222] usb usb1: New USB device found, idVendor=1d6b, > > > > > > > > > > > > idProduct=0001 > > > > > > > > > > > > [ 3.280231] usb usb1: New USB device strings: Mfr=3, Product=2, > > > > > > > SerialNumber=1 > > > > > > > [ 3.280236] usb usb1: Product: UHCI Host Controller > > > > > > > [ 3.280241] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd > > > > > > > [ 3.280245] usb usb1: SerialNumber: 0000:00:1d.0 > > > > > > > [ 3.280668] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7 > > > > > > > [ 3.280674] PCI: setting IRQ 7 as level-triggered > > > > > > > [ 3.280680] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> > > > > > > > > > > > > GSI 7 > > > > > > > > > > > > (level, low) -> IRQ 7 > > > > > > > [ 3.280699] PCI: Setting latency timer of device 0000:00:1d.1 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 3.280705] uhci_hcd 0000:00:1d.1: UHCI Host Controller > > > > > > > [ 3.280755] uhci_hcd 0000:00:1d.1: new USB bus registered, > > > > > > > > > > > > assigned bus > > > > > > > > > > > > number 2 > > > > > > > [ 3.280789] uhci_hcd 0000:00:1d.1: irq 7, io base 0x0000e480 > > > > > > > [ 3.280928] usb usb2: configuration #1 chosen from 1 choice > > > > > > > [ 3.280983] hub 2-0:1.0: USB hub found > > > > > > > [ 3.280997] hub 2-0:1.0: 2 ports detected > > > > > > > [ 3.281906] No dock devices found. > > > > > > > [ 3.352371] SCSI subsystem initialized > > > > > > > [ 3.384238] usb usb2: New USB device found, idVendor=1d6b, > > > > > > > > > > > > idProduct=0001 > > > > > > > > > > > > [ 3.384246] usb usb2: New USB device strings: Mfr=3, Product=2, > > > > > > > SerialNumber=1 > > > > > > > [ 3.384252] usb usb2: Product: UHCI Host Controller > > > > > > > [ 3.384256] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd > > > > > > > [ 3.384261] usb usb2: SerialNumber: 0000:00:1d.1 > > > > > > > [ 3.384330] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> > > > > > > > > > > > > GSI > > > > > > > > > > > > 10 (level, low) -> IRQ 10 > > > > > > > [ 3.384347] PCI: Setting latency timer of device 0000:00:1d.2 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 3.384354] uhci_hcd 0000:00:1d.2: UHCI Host Controller > > > > > > > [ 3.384399] uhci_hcd 0000:00:1d.2: new USB bus registered, > > > > > > > > > > > > assigned bus > > > > > > > > > > > > number 3 > > > > > > > [ 3.384433] uhci_hcd 0000:00:1d.2: irq 10, io base 0x0000e800 > > > > > > > [ 3.384577] usb usb3: configuration #1 chosen from 1 choice > > > > > > > [ 3.384629] hub 3-0:1.0: USB hub found > > > > > > > [ 3.384640] hub 3-0:1.0: 2 ports detected > > > > > > > [ 3.416319] libata version 3.00 loaded. > > > > > > > [ 3.488204] usb usb3: New USB device found, idVendor=1d6b, > > > > > > > > > > > > idProduct=0001 > > > > > > > > > > > > [ 3.488212] usb usb3: New USB device strings: Mfr=3, Product=2, > > > > > > > SerialNumber=1 > > > > > > > [ 3.488218] usb usb3: Product: UHCI Host Controller > > > > > > > [ 3.488223] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd > > > > > > > [ 3.488227] usb usb3: SerialNumber: 0000:00:1d.2 > > > > > > > [ 3.488303] ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> > > > > > > > > > > > > GSI 5 > > > > > > > > > > > > (level, low) -> IRQ 5 > > > > > > > [ 3.488320] PCI: Setting latency timer of device 0000:00:1d.3 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 3.488327] uhci_hcd 0000:00:1d.3: UHCI Host Controller > > > > > > > [ 3.488378] uhci_hcd 0000:00:1d.3: new USB bus registered, > > > > > > > > > > > > assigned bus > > > > > > > > > > > > number 4 > > > > > > > [ 3.488413] uhci_hcd 0000:00:1d.3: irq 5, io base 0x0000e880 > > > > > > > [ 3.488560] usb usb4: configuration #1 chosen from 1 choice > > > > > > > [ 3.488612] hub 4-0:1.0: USB hub found > > > > > > > [ 3.488625] hub 4-0:1.0: 2 ports detected > > > > > > > [ 3.592215] usb usb4: New USB device found, idVendor=1d6b, > > > > > > > > > > > > idProduct=0001 > > > > > > > > > > > > [ 3.592223] usb usb4: New USB device strings: Mfr=3, Product=2, > > > > > > > SerialNumber=1 > > > > > > > [ 3.592229] usb usb4: Product: UHCI Host Controller > > > > > > > [ 3.592234] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd > > > > > > > [ 3.592238] usb usb4: SerialNumber: 0000:00:1d.3 > > > > > > > [ 3.593865] ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> > > > > > > > > > > > > GSI 3 > > > > > > > > > > > > (level, low) -> IRQ 3 > > > > > > > [ 3.593890] PCI: Setting latency timer of device 0000:00:1d.7 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 3.593897] ehci_hcd 0000:00:1d.7: EHCI Host Controller > > > > > > > [ 3.593962] ehci_hcd 0000:00:1d.7: new USB bus registered, > > > > > > > > > > > > assigned bus > > > > > > > > > > > > number 5 > > > > > > > [ 3.597887] ehci_hcd 0000:00:1d.7: debug port 1 > > > > > > > [ 3.597896] PCI: cache line size of 32 is not supported by device > > > > > > > 0000:00:1d.7 > > > > > > > [ 3.597911] ehci_hcd 0000:00:1d.7: irq 3, io mem 0xf7eb7c00 > > > > > > > [ 3.624100] usb 2-1: new low speed USB device using uhci_hcd and > > > > > > > > > > > > address 2 > > > > > > > > > > > > [ 3.636034] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, > > > > > > > > > > > > driver > > > > > > > > > > > > 10 Dec 2004 > > > > > > > [ 3.636195] usb usb5: configuration #1 chosen from 1 choice > > > > > > > [ 3.636252] hub 5-0:1.0: USB hub found > > > > > > > [ 3.636267] hub 5-0:1.0: 8 ports detected > > > > > > > [ 3.692091] hub 2-0:1.0: unable to enumerate USB device on port 1 > > > > > > > [ 3.740226] usb usb5: New USB device found, idVendor=1d6b, > > > > > > > > > > > > idProduct=0002 > > > > > > > > > > > > [ 3.740234] usb usb5: New USB device strings: Mfr=3, Product=2, > > > > > > > SerialNumber=1 > > > > > > > [ 3.740240] usb usb5: Product: EHCI Host Controller > > > > > > > [ 3.740244] usb usb5: Manufacturer: Linux 2.6.26-1-686 ehci_hcd > > > > > > > [ 3.740249] usb usb5: SerialNumber: 0000:00:1d.7 > > > > > > > [ 3.740783] ahci 0000:00:1f.2: version 3.0 > > > > > > > [ 3.740819] ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> > > > > > > > > > > > > GSI 7 > > > > > > > > > > > > (level, low) -> IRQ 7 > > > > > > > [ 3.740844] ACPI: PCI interrupt for device 0000:00:1f.2 disabled > > > > > > > [ 3.740856] ahci: probe of 0000:00:1f.2 failed with error -22 > > > > > > > [ 3.745573] ata_piix 0000:00:1f.2: version 2.12 > > > > > > > [ 3.745593] ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> > > > > > > > > > > > > GSI 7 > > > > > > > > > > > > (level, low) -> IRQ 7 > > > > > > > [ 3.745603] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] > > > > > > > [ 3.745666] PCI: Setting latency timer of device 0000:00:1f.2 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 3.745758] scsi0 : ata_piix > > > > > > > [ 3.745903] scsi1 : ata_piix > > > > > > > [ 3.749073] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma > > > > > > > > > > > > 0xffa0 > > > > > > > > > > > > irq 14 > > > > > > > [ 3.749080] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma > > > > > > > > > > > > 0xffa8 > > > > > > > > > > > > irq 15 > > > > > > > [ 4.092738] ata2.00: ATA-5: ASUS-PHISON OB SSD, TST2.04U, max > > > > > > > > > > > > UDMA/66 > > > > > > > > > > > > [ 4.092746] ata2.00: 7880544 sectors, multi 0: LBA > > > > > > > [ 4.092784] ata2.01: ATA-5: ASUS-PHISON SSD, TST2.04P, max UDMA/66 > > > > > > > [ 4.092789] ata2.01: 31522176 sectors, multi 0: LBA > > > > > > > [ 4.100659] ata2.00: configured for UDMA/66 > > > > > > > [ 4.108633] ata2.01: configured for UDMA/66 > > > > > > > [ 4.108817] scsi 1:0:0:0: Direct-Access ATA ASUS-PHISON > > > > > > > > > > > > OB S > > > > > > > > > > > > TST2 PQ: 0 ANSI: 5 > > > > > > > [ 4.109109] scsi 1:0:1:0: Direct-Access ATA ASUS-PHISON > > > > > > > > > > > > SSD > > > > > > > > > > > > TST2 PQ: 0 ANSI: 5 > > > > > > > [ 4.126696] Uniform Multi-Platform E-IDE driver > > > > > > > [ 4.126708] ide: Assuming 33MHz system bus speed for PIO modes; > > > > > > > override with idebus=xx > > > > > > > [ 4.196148] Driver 'sd' needs updating - please use bus_type > > > > > > > > > > > > methods > > > > > > > > > > > > [ 4.196314] sd 1:0:0:0: [sda] 7880544 512-byte hardware sectors > > > > > > > > > > > > (4035 MB) > > > > > > > > > > > > [ 4.196348] sd 1:0:0:0: [sda] Write Protect is off > > > > > > > [ 4.196353] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 > > > > > > > [ 4.196409] sd 1:0:0:0: [sda] Write cache: disabled, read cache: > > > > > > > enabled, doesn't support DPO or FUA > > > > > > > [ 4.196525] sd 1:0:0:0: [sda] 7880544 512-byte hardware sectors > > > > > > > > > > > > (4035 MB) > > > > > > > > > > > > [ 4.196556] sd 1:0:0:0: [sda] Write Protect is off > > > > > > > [ 4.196563] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 > > > > > > > [ 4.196618] sd 1:0:0:0: [sda] Write cache: disabled, read cache: > > > > > > > enabled, doesn't support DPO or FUA > > > > > > > [ 4.196625] sda: sda1 > > > > > > > [ 4.198512] sd 1:0:0:0: [sda] Attached SCSI disk > > > > > > > [ 4.198653] sd 1:0:1:0: [sdb] 31522176 512-byte hardware sectors > > > > > > > > > > > > (16139 > > > > > > > > > > > > MB) > > > > > > > [ 4.198687] sd 1:0:1:0: [sdb] Write Protect is off > > > > > > > [ 4.198693] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > > > > > > > [ 4.198747] sd 1:0:1:0: [sdb] Write cache: disabled, read cache: > > > > > > > enabled, doesn't support DPO or FUA > > > > > > > [ 4.198847] sd 1:0:1:0: [sdb] 31522176 512-byte hardware sectors > > > > > > > > > > > > (16139 > > > > > > > > > > > > MB) > > > > > > > [ 4.198878] sd 1:0:1:0: [sdb] Write Protect is off > > > > > > > [ 4.198884] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > > > > > > > [ 4.198937] sd 1:0:1:0: [sdb] Write cache: disabled, read cache: > > > > > > > enabled, doesn't support DPO or FUA > > > > > > > [ 4.198945] sdb: sdb1 sdb2 < sdb5 > > > > > > > > [ 4.201758] sd 1:0:1:0: [sdb] Attached SCSI disk > > > > > > > [ 4.392601] PM: Starting manual resume from disk > > > > > > > [ 4.425481] kjournald starting. Commit interval 5 seconds > > > > > > > [ 4.425500] EXT3-fs: mounted filesystem with ordered data mode. > > > > > > > [ 4.744055] usb 5-5: new high speed USB device using ehci_hcd and > > > > > > > address 4 > > > > > > > [ 4.877440] usb 5-5: configuration #1 chosen from 1 choice > > > > > > > [ 4.877868] usb 5-5: New USB device found, idVendor=0951, > > > > > > > > > > > > idProduct=1606 > > > > > > > > > > > > [ 4.877875] usb 5-5: New USB device strings: Mfr=1, Product=2, > > > > > > > SerialNumber=4 > > > > > > > [ 4.877880] usb 5-5: Product: UB6225 > > > > > > > [ 4.877884] usb 5-5: Manufacturer: ENE > > > > > > > [ 4.877888] usb 5-5: SerialNumber: 146030377350 > > > > > > > [ 5.116092] usb 5-8: new high speed USB device using ehci_hcd and > > > > > > > address 5 > > > > > > > [ 5.128576] udevd version 125 started > > > > > > > [ 5.663525] usb 5-8: configuration #1 chosen from 1 choice > > > > > > > [ 5.665432] usb 5-8: New USB device found, idVendor=05e3, > > > > > > > > > > > > idProduct=0505 > > > > > > > > > > > > [ 5.665440] usb 5-8: New USB device strings: Mfr=0, Product=1, > > > > > > > SerialNumber=0 > > > > > > > [ 5.665445] usb 5-8: Product: USB 2.0 Camera > > > > > > > [ 5.904061] usb 2-1: new low speed USB device using uhci_hcd and > > > > > > > > > > > > address 3 > > > > > > > > > > > > [ 6.078974] usb 2-1: configuration #1 chosen from 1 choice > > > > > > > [ 6.092113] usb 2-1: New USB device found, idVendor=093a, > > > > > > > > > > > > idProduct=2510 > > > > > > > > > > > > [ 6.092121] usb 2-1: New USB device strings: Mfr=1, Product=2, > > > > > > > SerialNumber=0 > > > > > > > [ 6.092127] usb 2-1: Product: USB OPTICAL MOUSE > > > > > > > [ 6.092131] usb 2-1: Manufacturer: PIXART > > > > > > > [ 6.332049] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 4 > > > > > > > [ 6.452049] usb 2-2: device descriptor read/64, error -71 > > > > > > > [ 6.676048] usb 2-2: device descriptor read/64, error -71 > > > > > > > [ 6.892049] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 5 > > > > > > > [ 7.012056] usb 2-2: device descriptor read/64, error -71 > > > > > > > [ 7.184041] Linux agpgart interface v0.103 > > > > > > > [ 7.217692] agpgart: Detected an Intel 915GM Chipset. > > > > > > > [ 7.217903] agpgart: Detected 7932K stolen memory. > > > > > > > [ 7.238885] agpgart: AGP aperture is 256M @ 0xd0000000 > > > > > > > [ 7.238965] usb 2-2: device descriptor read/64, error -71 > > > > > > > [ 7.452044] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 6 > > > > > > > [ 7.860027] usb 2-2: device not accepting address 6, error -71 > > > > > > > [ 7.864253] Atheros(R) L2 Ethernet Driver - version 2.0.5 > > > > > > > [ 7.864259] Copyright (c) 2007 Atheros Corporation. > > > > > > > [ 7.864320] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKB] -> > > > > > > > > > > > > GSI > > > > > > > > > > > > 11 (level, low) -> IRQ 11 > > > > > > > [ 7.864339] PCI: Setting latency timer of device 0000:03:00.0 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 7.972048] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 7 > > > > > > > [ 8.153587] ath_hal: module license 'Proprietary' taints kernel. > > > > > > > [ 8.176070] AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, > > > > > > > > > > > > RF2413, > > > > > > > > > > > > RF5413, RF2133, RF2425, RF2417) > > > > > > > [ 8.179523] eeepc: Eee PC Hotkey Driver > > > > > > > [ 8.179764] eeepc: Hotkey init flags 0x41 > > > > > > > [ 8.181034] eeepc: Get control methods supported: 0x101711 > > > > > > > [ 8.189538] input: Power Button (FF) as /class/input/input1 > > > > > > > [ 8.216368] ACPI: Power Button (FF) [PWRF] > > > > > > > [ 8.216521] input: Lid Switch as /class/input/input2 > > > > > > > [ 8.245309] ACPI: Lid Switch [LID] > > > > > > > [ 8.245427] input: Sleep Button (CM) as /class/input/input3 > > > > > > > [ 8.275834] ACPI: Sleep Button (CM) [SLPB] > > > > > > > [ 8.275940] input: Power Button (CM) as /class/input/input4 > > > > > > > [ 8.303486] ACPI: Power Button (CM) [PWRB] > > > > > > > [ 8.384026] usb 2-2: device not accepting address 7, error -71 > > > > > > > [ 8.384135] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 8.550914] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKC] -> > > > > > > > > > > > > GSI > > > > > > > > > > > > 10 (level, low) -> IRQ 10 > > > > > > > [ 8.550934] PCI: Setting latency timer of device 0000:01:00.0 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 9.042244] MadWifi: ath_attach: Switching rfkill capability off. > > > > > > > [ 9.735124] ACPI: AC Adapter [AC0] (on-line) > > > > > > > [ 10.756737] ACPI: EC: missing confirmations, switch off interrupt > > > > > > > > > > > > mode. > > > > > > > > > > > > [ 11.208450] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 > > > > > > > > > > > > (30-Apr-2008) > > > > > > > > > > > > [ 11.208577] iTCO_wdt: Found a ICH6-M TCO device (Version=2, > > > > > > > TCOBASE=0x0860) > > > > > > > [ 11.208620] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) > > > > > > > [ 11.477769] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> > > > > > > > > > > > > GSI 5 > > > > > > > > > > > > (level, low) -> IRQ 5 > > > > > > > [ 11.477805] PCI: Setting latency timer of device 0000:00:1b.0 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 11.483562] input: PC Speaker as /class/input/input5 > > > > > > > [ 11.501902] hda_codec: Unknown model for ALC662, trying auto-probe > > > > > > > > > > > > from > > > > > > > > > > > > BIOS... > > > > > > > [ 11.540394] ACPI: Battery Slot [BAT0] (battery present) > > > > > > > [ 11.541343] input: Video Bus as /class/input/input6 > > > > > > > [ 11.548119] intel_rng: FWH not detected > > > > > > > [ 11.568109] ACPI: Video Device [VGA] (multi-head: yes rom: no > > > > > > > > > > > > post: no) > > > > > > > > > > > > [ 12.410100] Initializing USB Mass Storage driver... > > > > > > > [ 12.410257] scsi2 : SCSI emulation for USB Mass Storage devices > > > > > > > [ 12.410408] usbcore: registered new interface driver usb-storage > > > > > > > [ 12.410415] USB Mass Storage support registered. > > > > > > > [ 12.419980] usb-storage: device found at 4 > > > > > > > [ 12.419987] usb-storage: waiting for device to settle before > > > > > > > > > > > > scanning > > > > > > > > > > > > [ 12.467956] Linux video capture interface: v2.00 > > > > > > > [ 12.501378] uvcvideo: Found UVC 1.00 device USB 2.0 Camera > > > > > > > > > > > > (05e3:0505) > > > > > > > > > > > > [ 12.675603] usbcore: registered new interface driver uvcvideo > > > > > > > [ 12.675612] USB Video Class driver (v0.1.0) > > > > > > > [ 12.690664] usbcore: registered new interface driver hiddev > > > > > > > [ 12.706770] input: PIXART USB OPTICAL MOUSE as /class/input/input7 > > > > > > > [ 12.732114] input,hidraw0: USB HID v1.10 Mouse [PIXART USB OPTICAL > > > > > > > MOUSE] on usb-0000:00:1d.1-1 > > > > > > > [ 12.732155] usbcore: registered new interface driver usbhid > > > > > > > [ 12.732161] usbhid: v2.6:USB HID core driver > > > > > > > [ 13.367766] wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip > > > > > > > > > > > > 7.0, > > > > > > > > > > > > Radio 10.2) > > > > > > > [ 13.491684] ath_pci: wifi0: Atheros 5424/2424: mem=0xfbef0000, > > > > > > > > > > > > irq=10 > > > > > > > > > > > > [ 13.493167] ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKD] -> > > > > > > > > > > > > GSI 7 > > > > > > > > > > > > (level, low) -> IRQ 7 > > > > > > > [ 14.103195] input: ImPS/2 Logitech Wheel Mouse as > > > > > > > > > > > > /class/input/input8 > > > > > > > > > > > > [ 14.612235] Adding 706820k swap on /dev/sdb5. Priority:-1 > > > > > > > > > > > > extents:1 > > > > > > > > > > > > across:706820k > > > > > > > [ 14.741005] EXT3 FS on sdb1, internal journal > > > > > > > [ 15.148504] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > > > > > > > [ 15.156599] pciehp: HPC vendor_id 8086 device_id 2660 ss_vid 0 > > > > > > > > > > > > ss_did 0 > > > > > > > > > > > > [ 15.156711] Load service driver hpdriver on pcie device > > > > > > > 0000:00:1c.0:pcie02 > > > > > > > [ 15.156733] pciehp: HPC vendor_id 8086 device_id 2662 ss_vid 0 > > > > > > > > > > > > ss_did 0 > > > > > > > > > > > > [ 16.160089] pciehp: Device 0000:03:00.0 already exists at 3:0, > > > > > > > > > > > > cannot > > > > > > > > > > > > hot-add > > > > > > > [ 16.160202] pciehp: Cannot add device 0x3:0 > > > > > > > [ 17.164098] Load service driver hpdriver on pcie device > > > > > > > 0000:00:1c.1:pcie02 > > > > > > > [ 17.164136] pciehp: HPC vendor_id 8086 device_id 2664 ss_vid 0 > > > > > > > > > > > > ss_did 0 > > > > > > > > > > > > [ 17.416293] usb-storage: device scan complete > > > > > > > [ 17.416756] scsi 2:0:0:0: Direct-Access USB2.0 CardReader > > > > > > > > > > > > SD0 > > > > > > > > > > > > 0100 PQ: 0 ANSI: 0 > > > > > > > [ 17.418374] sd 2:0:0:0: [sdc] Attached SCSI removable disk > > > > > > > [ 18.168064] pciehp: Device 0000:01:00.0 already exists at 1:0, > > > > > > > > > > > > cannot > > > > > > > > > > > > hot-add > > > > > > > [ 18.168156] pciehp: Cannot add device 0x1:0 > > > > > > > [ 19.172058] Load service driver hpdriver on pcie device > > > > > > > 0000:00:1c.2:pcie02 > > > > > > > [ 19.172108] pciehp: PCI Express Hot Plug Controller Driver > > > > > > > > > > > > version: 0.4 > > > > > > > > > > > > [ 32.817916] lp: driver loaded but no devices found > > > > > > > [ 32.878596] ppdev: user-space parallel port driver > > > > > > > [ 33.353445] NET: Registered protocol family 10 > > > > > > > [ 33.354326] lo: Disabled Privacy Extensions > > > > > > > [ 33.355270] ADDRCONF(NETDEV_UP): eth0: link is not ready > > > > > > > [ 34.573246] warning: `avahi-daemon' uses 32-bit capabilities > > > > > > > > > > > > (legacy > > > > > > > > > > > > support in use) > > > > > > > [ 43.156412] Bluetooth: Core ver 2.11 > > > > > > > [ 43.158622] NET: Registered protocol family 31 > > > > > > > [ 43.158632] Bluetooth: HCI device and connection manager > > > > > > > > > > > > initialized > > > > > > > > > > > > [ 43.158638] Bluetooth: HCI socket layer initialized > > > > > > > [ 43.235432] Bluetooth: L2CAP ver 2.9 > > > > > > > [ 43.235441] Bluetooth: L2CAP socket layer initialized > > > > > > > [ 43.311284] Bluetooth: RFCOMM socket layer initialized > > > > > > > [ 43.311306] Bluetooth: RFCOMM TTY layer initialized > > > > > > > [ 43.311310] Bluetooth: RFCOMM ver 1.8 > > > > > > > [ 49.437113] [drm] Initialized drm 1.1.0 20060810 > > > > > > > [ 50.574435] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> > > > > > > > > > > > > GSI 5 > > > > > > > > > > > > (level, low) -> IRQ 5 > > > > > > > [ 50.574454] PCI: Setting latency timer of device 0000:00:02.0 to > > > > > > > > > > > > 64 > > > > > > > > > > > > [ 50.574592] [drm] Initialized i915 1.6.0 20060119 on minor 0 > > > > > > > [ 95.536152] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready > > > > > > > [ 111.140013] ath0: no IPv6 routers present > > > > > > > [ 321.816064] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 8 > > > > > > > [ 321.872078] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 323.056069] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 9 > > > > > > > [ 323.198730] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 323.256090] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 324.296074] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 11 > > > > > > > [ 324.352091] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 325.536036] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 12 > > > > > > > [ 325.686747] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 325.686747] usb 2-2: can't read configurations, error -71 > > > > > > > [ 325.744091] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 326.776039] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 14 > > > > > > > [ 326.832092] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 328.016070] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 15 > > > > > > > [ 328.072161] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 329.256077] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 16 > > > > > > > [ 329.312097] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 330.496075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 17 > > > > > > > [ 330.552108] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 331.736069] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 18 > > > > > > > [ 331.878747] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 331.936095] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 332.976078] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 20 > > > > > > > [ 333.118668] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 333.176108] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 334.216075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 22 > > > > > > > [ 334.272108] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 335.456137] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 23 > > > > > > > [ 335.512118] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 336.696071] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 24 > > > > > > > [ 336.838739] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 336.896067] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 337.936069] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 26 > > > > > > > [ 337.992105] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 339.176075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 27 > > > > > > > [ 339.236097] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 340.416067] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 28 > > > > > > > [ 340.476107] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 341.656078] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 29 > > > > > > > [ 341.827652] usb 2-2: configuration #1 chosen from 1 choice > > > > > > > [ 341.833292] usb 2-2: can't set config #1, error -71 > > > > > > > [ 341.833436] usb 2-2: New USB device found, idVendor=04d8, > > > > > > > > > > > > idProduct=000a > > > > > > > > > > > > [ 341.833443] usb 2-2: New USB device strings: Mfr=1, Product=2, > > > > > > > SerialNumber=3 > > > > > > > [ 341.833468] usb 2-2: USB disconnect, address 29 > > > > > > > [ 342.896078] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 30 > > > > > > > [ 342.952095] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 344.136074] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 31 > > > > > > > [ 344.192112] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 345.376075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 32 > > > > > > > [ 345.436065] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 346.616073] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 33 > > > > > > > [ 346.758870] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 346.816090] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 347.856079] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 35 > > > > > > > [ 347.998741] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 348.056093] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 349.096073] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 37 > > > > > > > [ 349.246504] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 349.246504] usb 2-2: can't read configurations, error -71 > > > > > > > [ 349.304144] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 350.336071] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 39 > > > > > > > [ 350.486581] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 350.486581] usb 2-2: can't read configurations, error -71 > > > > > > > [ 350.544097] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 351.576075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 41 > > > > > > > [ 351.729542] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 351.729542] usb 2-2: can't read configurations, error -71 > > > > > > > [ 351.784099] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 352.816067] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 43 > > > > > > > [ 352.872105] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 354.056173] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 44 > > > > > > > [ 354.198756] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 354.256102] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 355.296075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 46 > > > > > > > [ 355.446516] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 355.446516] usb 2-2: can't read configurations, error -71 > > > > > > > [ 355.504102] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 356.536041] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 48 > > > > > > > [ 356.686702] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 356.686702] usb 2-2: can't read configurations, error -71 > > > > > > > [ 356.744059] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 357.776045] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 50 > > > > > > > [ 357.926582] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 357.926582] usb 2-2: can't read configurations, error -71 > > > > > > > [ 357.984071] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 359.016069] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 52 > > > > > > > [ 359.072171] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 360.256077] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 53 > > > > > > > [ 360.316100] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 361.496046] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 54 > > > > > > > [ 361.646872] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 361.646883] usb 2-2: can't read configurations, error -71 > > > > > > > [ 361.704071] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 362.736071] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 56 > > > > > > > [ 362.878746] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 362.936069] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 363.976081] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 58 > > > > > > > [ 364.032099] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 365.216069] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 59 > > > > > > > [ 365.361850] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 365.416095] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 366.456076] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 61 > > > > > > > [ 366.512099] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 367.696078] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 62 > > > > > > > [ 367.838690] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 367.896101] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 368.936044] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 64 > > > > > > > [ 368.992106] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 370.176080] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 65 > > > > > > > [ 370.232103] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 371.416073] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 66 > > > > > > > [ 371.472106] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 372.656082] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 67 > > > > > > > [ 372.712103] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 373.896080] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 68 > > > > > > > [ 374.045624] usb 2-2: unable to read config index 0 > > > > > > > > > > > > descriptor/start: -71 > > > > > > > > > > > > [ 374.045624] usb 2-2: chopping to 0 config(s) > > > > > > > [ 374.053868] usb 2-2: string descriptor 0 read error: -71 > > > > > > > [ 374.061828] usb 2-2: string descriptor 0 read error: -71 > > > > > > > [ 374.069525] usb 2-2: string descriptor 0 read error: -71 > > > > > > > [ 374.069525] usb 2-2: no configuration chosen from 0 choices > > > > > > > [ 374.069525] usb 2-2: New USB device found, idVendor=04d8, > > > > > > > > > > > > idProduct=000a > > > > > > > > > > > > [ 374.069525] usb 2-2: New USB device strings: Mfr=1, Product=2, > > > > > > > SerialNumber=3 > > > > > > > [ 374.069525] usb 2-2: USB disconnect, address 68 > > > > > > > [ 375.136075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 69 > > > > > > > [ 375.192110] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 376.376083] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 70 > > > > > > > [ 376.432100] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 377.616075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 71 > > > > > > > [ 377.767653] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 377.767653] usb 2-2: can't read configurations, error -71 > > > > > > > [ 377.824096] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 378.856084] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 73 > > > > > > > [ 378.912074] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 380.096078] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 74 > > > > > > > [ 380.246755] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 380.246755] usb 2-2: can't read configurations, error -71 > > > > > > > [ 380.304106] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 381.336075] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 76 > > > > > > > [ 381.392112] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 382.576042] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 77 > > > > > > > [ 382.718749] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 382.776103] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 383.816074] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 79 > > > > > > > [ 383.966777] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 383.966777] usb 2-2: can't read configurations, error -71 > > > > > > > [ 384.024099] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 385.056078] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 81 > > > > > > > [ 385.112104] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 386.296083] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 82 > > > > > > > [ 386.352162] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 387.536079] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 83 > > > > > > > [ 387.592105] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 388.776083] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 84 > > > > > > > [ 388.926509] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 388.926509] usb 2-2: can't read configurations, error -71 > > > > > > > [ 388.984109] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 390.016074] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 86 > > > > > > > [ 390.158884] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 390.216060] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 391.256077] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 88 > > > > > > > [ 391.406576] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 391.406576] usb 2-2: can't read configurations, error -71 > > > > > > > [ 391.464106] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 392.496156] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 90 > > > > > > > [ 392.552101] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 393.736084] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 91 > > > > > > > [ 393.792110] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 394.976043] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 92 > > > > > > > [ 395.121683] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 395.176103] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 396.216038] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 94 > > > > > > > [ 396.366761] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 396.366762] usb 2-2: can't read configurations, error -71 > > > > > > > [ 396.424065] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 397.456073] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 96 > > > > > > > [ 397.606587] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 397.606587] usb 2-2: can't read configurations, error -71 > > > > > > > [ 397.664109] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 398.696080] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 98 > > > > > > > [ 398.838747] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 398.896068] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 399.936072] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 100 > > > > > > > [ 400.085736] usb 2-2: unable to read config index 0 > > > > > > > > > > > > descriptor/start: -71 > > > > > > > > > > > > [ 400.085736] usb 2-2: chopping to 0 config(s) > > > > > > > [ 400.093874] usb 2-2: string descriptor 0 read error: -71 > > > > > > > [ 400.101757] usb 2-2: string descriptor 0 read error: -71 > > > > > > > [ 400.109490] usb 2-2: string descriptor 0 read error: -71 > > > > > > > [ 400.109490] usb 2-2: no configuration chosen from 0 choices > > > > > > > [ 400.109490] usb 2-2: New USB device found, idVendor=04d8, > > > > > > > > > > > > idProduct=000a > > > > > > > > > > > > [ 400.109490] usb 2-2: New USB device strings: Mfr=1, Product=2, > > > > > > > SerialNumber=3 > > > > > > > [ 400.109490] usb 2-2: USB disconnect, address 100 > > > > > > > [ 401.176045] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 101 > > > > > > > [ 401.232064] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 402.416082] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 102 > > > > > > > [ 402.472111] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 403.656082] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 103 > > > > > > > [ 403.712103] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 404.896044] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 104 > > > > > > > [ 404.952098] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 406.136072] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 105 > > > > > > > [ 406.192107] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 407.376078] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 106 > > > > > > > [ 407.432115] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 408.616099] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 107 > > > > > > > [ 408.766762] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 408.766762] usb 2-2: can't read configurations, error -71 > > > > > > > [ 408.824118] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 409.856084] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 109 > > > > > > > [ 409.912132] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 411.096048] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 110 > > > > > > > [ 411.245982] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 411.245982] usb 2-2: can't read configurations, error -71 > > > > > > > [ 411.304077] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 412.336053] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 112 > > > > > > > [ 412.392081] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 413.576055] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 113 > > > > > > > [ 413.632078] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 414.816046] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 114 > > > > > > > [ 414.872082] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 416.056052] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 115 > > > > > > > [ 416.207055] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 416.207055] usb 2-2: can't read configurations, error -71 > > > > > > > [ 416.264080] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 417.296046] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 117 > > > > > > > [ 417.446150] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 417.446150] usb 2-2: can't read configurations, error -71 > > > > > > > [ 417.504136] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 418.536048] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 119 > > > > > > > [ 418.686768] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 418.686768] usb 2-2: can't read configurations, error -71 > > > > > > > [ 418.744077] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 419.776055] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 121 > > > > > > > [ 419.832073] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 421.016049] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 122 > > > > > > > [ 421.072088] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 422.256049] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 123 > > > > > > > [ 422.398770] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 422.456076] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 423.496051] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 125 > > > > > > > [ 423.646900] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 423.646914] usb 2-2: can't read configurations, error -71 > > > > > > > [ 423.704075] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 424.736046] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 127 > > > > > > > [ 424.886764] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 424.886778] usb 2-2: can't read configurations, error -71 > > > > > > > [ 424.944071] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 425.976048] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 4 > > > > > > > [ 426.121685] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 426.176082] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 427.216049] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 6 > > > > > > > [ 427.272083] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 428.456049] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 7 > > > > > > > [ 428.512072] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 429.696049] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 8 > > > > > > > [ 429.752079] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 430.936052] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 9 > > > > > > > [ 431.086733] usb 2-2: unable to read config index 0 descriptor/all > > > > > > > [ 431.086733] usb 2-2: can't read configurations, error -71 > > > > > > > [ 431.144075] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > [ 432.176055] usb 2-2: new full speed USB device using uhci_hcd and > > > > > > > address 11 > > > > > > > [ 432.318826] usb 2-2: device descriptor read/all, error -71 > > > > > > > [ 432.376080] hub 2-0:1.0: unable to enumerate USB device on port 2 > > > > > > > > > > > > > > lsmod -v: > > > > > > > Module Size Used by > > > > > > > wlan_ccmp 6496 2 > > > > > > > i915 25280 2 > > > > > > > drm 65256 3 i915 > > > > > > > rfcomm 28272 0 > > > > > > > l2cap 17248 5 rfcomm > > > > > > > bluetooth 44900 4 rfcomm,l2cap > > > > > > > ipv6 235300 14 > > > > > > > ppdev 6468 0 > > > > > > > parport_pc 22500 0 > > > > > > > lp 8164 0 > > > > > > > parport 30988 3 ppdev,parport_pc,lp > > > > > > > cpufreq_powersave 1856 0 > > > > > > > cpufreq_stats 3776 0 > > > > > > > cpufreq_userspace 3172 0 > > > > > > > cpufreq_ondemand 6476 0 > > > > > > > cpufreq_conservative 5960 0 > > > > > > > freq_table 4224 2 cpufreq_stats,cpufreq_ondemand > > > > > > > cdc_acm 12224 0 > > > > > > > pciehp 28540 0 > > > > > > > pci_hotplug 23460 1 pciehp > > > > > > > wlan_scan_sta 11296 1 > > > > > > > usbhid 35904 0 > > > > > > > hid 33184 1 usbhid > > > > > > > ff_memless 4392 1 usbhid > > > > > > > uvcvideo 45704 0 > > > > > > > compat_ioctl32 1312 1 uvcvideo > > > > > > > videodev 27520 1 uvcvideo > > > > > > > v4l1_compat 12260 2 uvcvideo,videodev > > > > > > > usb_storage 75936 0 > > > > > > > serio_raw 4740 0 > > > > > > > psmouse 32336 0 > > > > > > > rng_core 3940 0 > > > > > > > pcspkr 2432 0 > > > > > > > i2c_i801 7920 0 > > > > > > > snd_hda_intel 324248 1 > > > > > > > i2c_core 19828 1 i2c_i801 > > > > > > > snd_pcm_oss 32800 0 > > > > > > > snd_pcm 62596 2 snd_hda_intel,snd_pcm_oss > > > > > > > iTCO_wdt 9508 0 > > > > > > > snd_mixer_oss 12320 1 snd_pcm_oss > > > > > > > video 16432 0 > > > > > > > output 2912 1 video > > > > > > > battery 10180 0 > > > > > > > snd_seq_dummy 2660 0 > > > > > > > ac 4196 0 > > > > > > > ath_rate_sample 11104 1 > > > > > > > ath_pci 202712 0 > > > > > > > eeepc_laptop 7440 0 > > > > > > > button 6096 0 > > > > > > > wlan 194000 5 > > > > > > > wlan_ccmp,wlan_scan_sta,ath_rate_sample,ath_pci > > > > > > > ath_hal 300768 3 ath_rate_sample,ath_pci > > > > > > > atl2 22744 0 > > > > > > > snd_seq_oss 24992 0 > > > > > > > snd_seq_midi_event 6432 1 snd_seq_oss > > > > > > > snd_seq 41456 5 > > > > > > > > > > > > snd_seq_dummy,snd_seq_oss,snd_seq_midi_event > > > > > > > > > > > > snd_timer 17800 2 snd_pcm,snd_seq > > > > > > > snd_seq_device 6380 3 snd_seq_dummy,snd_seq_oss,snd_seq > > > > > > > snd 45604 10 > > > > > > > snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_seq,snd_timer,snd_seq_device > > > > > > > intel_agp 22332 1 > > > > > > > agpgart 28776 3 drm,intel_agp > > > > > > > soundcore 6368 1 snd > > > > > > > snd_page_alloc 7816 2 snd_hda_intel,snd_pcm > > > > > > > evdev 8000 6 > > > > > > > ext3 105512 1 > > > > > > > jbd 39444 1 ext3 > > > > > > > mbcache 7108 1 ext3 > > > > > > > sd_mod 22200 3 > > > > > > > ide_pci_generic 3908 0 [permanent] > > > > > > > ide_core 96168 1 ide_pci_generic > > > > > > > ata_generic 4676 0 > > > > > > > ata_piix 14180 2 > > > > > > > ahci 23176 0 > > > > > > > libata 140384 3 ata_generic,ata_piix,ahci > > > > > > > scsi_mod 129356 3 usb_storage,sd_mod,libata > > > > > > > dock 8304 1 libata > > > > > > > ehci_hcd 28428 0 > > > > > > > uhci_hcd 18672 0 > > > > > > > usbcore 118160 7 > > > > > > > cdc_acm,usbhid,uvcvideo,usb_storage,ehci_hcd,uhci_hcd > > > > > > > thermal 15228 0 > > > > > > > processor 32576 2 thermal > > > > > > > fan 4164 0 > > > > > > > thermal_sys 10856 4 video,thermal,processor,fan > > > > > > > > > > > > > > lspci: > > > > > > > 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML > > > > > > > > > > > > Express > > > > > > > > > > > > Processor to DRAM Controller (rev 04) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d9 > > > > > > > Flags: bus master, fast devsel, latency 0 > > > > > > > Capabilities: [e0] Vendor Specific Information <?> > > > > > > > Kernel driver in use: agpgart-intel > > > > > > > Kernel modules: intel-agp > > > > > > > > > > > > > > 00:02.0 VGA compatible controller: Intel Corporation Mobile > > > > > > > 915GM/GMS/910GML Express Graphics Controller (rev 04) (prog-if 00 > > > > > > > > > > > > [VGA > > > > > > > > > > > > controller]) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d9 > > > > > > > Flags: bus master, fast devsel, latency 0, IRQ 16 > > > > > > > Memory at f7f00000 (32-bit, non-prefetchable) [size=512K] > > > > > > > I/O ports at ec00 [size=8] > > > > > > > Memory at d0000000 (32-bit, prefetchable) [size=256M] > > > > > > > Memory at f7ec0000 (32-bit, non-prefetchable) [size=256K] > > > > > > > Capabilities: [d0] Power Management version 2 > > > > > > > Kernel modules: intelfb > > > > > > > > > > > > > > 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML > > > > > > > Express Graphics Controller (rev 04) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d9 > > > > > > > Flags: bus master, fast devsel, latency 0 > > > > > > > Memory at f7f80000 (32-bit, non-prefetchable) [size=512K] > > > > > > > Capabilities: [d0] Power Management version 2 > > > > > > > > > > > > > > 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > Family) High Definition Audio Controller (rev 04) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 8337 > > > > > > > Flags: bus master, fast devsel, latency 0, IRQ 16 > > > > > > > Memory at f7eb8000 (64-bit, non-prefetchable) [size=16K] > > > > > > > Capabilities: [50] Power Management version 2 > > > > > > > Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ > > > > > > > > > > > > Queue=0/0 > > > > > > > > > > > > Enable- > > > > > > > Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 > > > > > > > Capabilities: [100] Virtual Channel <?> > > > > > > > Capabilities: [130] Root Complex Link <?> > > > > > > > Kernel driver in use: HDA Intel > > > > > > > Kernel modules: snd-hda-intel > > > > > > > > > > > > > > 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > > > > > > Family) > > > > > > > > > > > > PCI Express Port 1 (rev 04) (prog-if 00 [Normal decode]) > > > > > > > Flags: bus master, fast devsel, latency 0 > > > > > > > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > > > > > > > Capabilities: [40] Express Root Port (Slot+), MSI 00 > > > > > > > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- > > > > > > > > > > > > Queue=0/0 > > > > > > > > > > > > Enable+ > > > > > > > Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Capabilities: [a0] Power Management version 2 > > > > > > > Capabilities: [100] Virtual Channel <?> > > > > > > > Capabilities: [180] Root Complex Link <?> > > > > > > > Kernel driver in use: pcieport-driver > > > > > > > Kernel modules: shpchp > > > > > > > > > > > > > > 00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > > > > > > Family) > > > > > > > > > > > > PCI Express Port 2 (rev 04) (prog-if 00 [Normal decode]) > > > > > > > Flags: bus master, fast devsel, latency 0 > > > > > > > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > > > > > > > Memory behind bridge: fbf00000-fbffffff > > > > > > > Capabilities: [40] Express Root Port (Slot+), MSI 00 > > > > > > > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- > > > > > > > > > > > > Queue=0/0 > > > > > > > > > > > > Enable+ > > > > > > > Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Capabilities: [a0] Power Management version 2 > > > > > > > Capabilities: [100] Virtual Channel <?> > > > > > > > Capabilities: [180] Root Complex Link <?> > > > > > > > Kernel driver in use: pcieport-driver > > > > > > > Kernel modules: shpchp > > > > > > > > > > > > > > 00:1c.2 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > > > > > > Family) > > > > > > > > > > > > PCI Express Port 3 (rev 04) (prog-if 00 [Normal decode]) > > > > > > > Flags: bus master, fast devsel, latency 0 > > > > > > > Bus: primary=00, secondary=01, subordinate=02, sec-latency=0 > > > > > > > Memory behind bridge: f8000000-fbefffff > > > > > > > Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff > > > > > > > Capabilities: [40] Express Root Port (Slot+), MSI 00 > > > > > > > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- > > > > > > > > > > > > Queue=0/0 > > > > > > > > > > > > Enable+ > > > > > > > Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Capabilities: [a0] Power Management version 2 > > > > > > > Capabilities: [100] Virtual Channel <?> > > > > > > > Capabilities: [180] Root Complex Link <?> > > > > > > > Kernel driver in use: pcieport-driver > > > > > > > Kernel modules: shpchp > > > > > > > > > > > > > > 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI]) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Flags: bus master, medium devsel, latency 0, IRQ 23 > > > > > > > I/O ports at e400 [size=32] > > > > > > > Kernel driver in use: uhci_hcd > > > > > > > Kernel modules: uhci-hcd > > > > > > > > > > > > > > 00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI]) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Flags: bus master, medium devsel, latency 0, IRQ 19 > > > > > > > I/O ports at e480 [size=32] > > > > > > > Kernel driver in use: uhci_hcd > > > > > > > Kernel modules: uhci-hcd > > > > > > > > > > > > > > 00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI]) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Flags: bus master, medium devsel, latency 0, IRQ 18 > > > > > > > I/O ports at e800 [size=32] > > > > > > > Kernel driver in use: uhci_hcd > > > > > > > Kernel modules: uhci-hcd > > > > > > > > > > > > > > 00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI]) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Flags: bus master, medium devsel, latency 0, IRQ 16 > > > > > > > I/O ports at e880 [size=32] > > > > > > > Kernel driver in use: uhci_hcd > > > > > > > Kernel modules: uhci-hcd > > > > > > > > > > > > > > 00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 > > > > > > > Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI]) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Flags: bus master, medium devsel, latency 0, IRQ 23 > > > > > > > Memory at f7eb7c00 (32-bit, non-prefetchable) [size=1K] > > > > > > > Capabilities: [50] Power Management version 2 > > > > > > > Capabilities: [58] Debug port: BAR=1 offset=00a0 > > > > > > > Kernel driver in use: ehci_hcd > > > > > > > Kernel modules: ehci-hcd > > > > > > > > > > > > > > 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev > > > > > > > > > > > > d4) > > > > > > > > > > > > (prog-if 01 [Subtractive decode]) > > > > > > > Flags: bus master, fast devsel, latency 0 > > > > > > > Bus: primary=00, secondary=05, subordinate=05, sec-latency=32 > > > > > > > Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > > > > > > > > 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface > > > > > > > Bridge (rev 04) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Flags: bus master, medium devsel, latency 0 > > > > > > > Kernel modules: intel-rng, iTCO_wdt > > > > > > > > > > > > > > 00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA > > > > > > > > > > > > Controller > > > > > > > > > > > > (rev 04) (prog-if 80 [Master]) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 > > > > > > > I/O ports at 01f0 [size=8] > > > > > > > I/O ports at 03f4 [size=1] > > > > > > > I/O ports at 0170 [size=8] > > > > > > > I/O ports at 0374 [size=1] > > > > > > > I/O ports at ffa0 [size=16] > > > > > > > Capabilities: [70] Power Management version 2 > > > > > > > Kernel driver in use: ata_piix > > > > > > > Kernel modules: ahci, ata_piix > > > > > > > > > > > > > > 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) > > > > > > > > > > > > SMBus > > > > > > > > > > > > Controller (rev 04) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 82d8 > > > > > > > Flags: medium devsel, IRQ 19 > > > > > > > I/O ports at 0400 [size=32] > > > > > > > Kernel driver in use: i801_smbus > > > > > > > Kernel modules: i2c-i801 > > > > > > > > > > > > > > 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x > > > > > > > > > > > > 802.11abg > > > > > > > > > > > > Wireless PCI Express Adapter (rev 01) > > > > > > > Subsystem: Device 1a3b:1026 > > > > > > > Flags: bus master, fast devsel, latency 0, IRQ 18 > > > > > > > Memory at fbef0000 (64-bit, non-prefetchable) [size=64K] > > > > > > > Capabilities: [40] Power Management version 2 > > > > > > > Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- > > > > > > > > > > > > Queue=0/0 > > > > > > > > > > > > Enable- > > > > > > > Capabilities: [60] Express Legacy Endpoint, MSI 00 > > > > > > > Capabilities: [90] MSI-X: Enable- Mask- TabSize=1 > > > > > > > Capabilities: [100] Advanced Error Reporting <?> > > > > > > > Capabilities: [140] Virtual Channel <?> > > > > > > > Kernel driver in use: ath_pci > > > > > > > Kernel modules: ath_pci, ath5k > > > > > > > > > > > > > > 03:00.0 Ethernet controller: Attansic Technology Corp. L2 100 Mbit > > > > > > > Ethernet Adapter (rev a0) > > > > > > > Subsystem: ASUSTeK Computer Inc. Device 8233 > > > > > > > Flags: bus master, fast devsel, latency 0, IRQ 220 > > > > > > > Memory at fbfc0000 (64-bit, non-prefetchable) [size=256K] > > > > > > > Expansion ROM at fbfa0000 [disabled] [size=128K] > > > > > > > Capabilities: [40] Power Management version 2 > > > > > > > Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ > > > > > > > > > > > > Queue=0/0 > > > > > > > > > > > > Enable+ > > > > > > > Capabilities: [58] Express Endpoint, MSI 00 > > > > > > > Capabilities: [6c] Vital Product Data <?> > > > > > > > Capabilities: [100] Advanced Error Reporting <?> > > > > > > > Kernel driver in use: atl2 > > > > > > > Kernel modules: atl2 > > > > > > > > > > > > > > > > > > > > > Any suggestion is very welcome. > > > > > > > Thanks. > > > > > > > Wim > > > > > > > > > > > > > > > > > > > > > > > > > > > > -- > > > > > > > To unsubscribe from this list: send the line "unsubscribe linux-usb" > > > > > > > > > > > > in > > > > > > > > > > > > the body of a message to majordomo@xxxxxxxxxxxxxxx > > > > > > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
