On 03/23/2016 10:21 PM, Peter Chen wrote:
On Wed, Mar 23, 2016 at 02:17:27PM -0400, Jaret Cantu wrote:
On 03/23/2016 01:37 PM, Jaret Cantu wrote:
On 03/23/2016 12:36 AM, Peter Chen wrote:
On Mon, Mar 21, 2016 at 12:32:27PM -0400, Jaret Cantu wrote:
The TX settings can be calibrated for particular hardware. The
phy is reset by Linux, so this cannot be handled by the bootloader.
The TRM mentions that the maximum resistance should be used for the
DN/DP calibration in order to pass USB certification.
The values for the TX registers are poorly described in the TRM.
The meanings of the register values were taken from another
Freescale-provided document:
https://community.freescale.com/message/566147#comment-566912
Signed-off-by: Jaret Cantu <jaret.cantu@xxxxxxxxxxx>
---
v3. Added unit suffix (-ohms) to tx-cal-45-d*
v2. Copying devicetree list
Removed prettifying extra whitespace
Removed unnecessary register rewrite on resume
Use min and max constants for clarity
.../devicetree/bindings/phy/mxs-usb-phy.txt | 10 ++++
drivers/usb/phy/phy-mxs-usb.c | 58
++++++++++++++++++++
2 files changed, 68 insertions(+)
diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt
b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt
index 379b84a..1d25b04 100644
--- a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt
@@ -12,6 +12,16 @@ Required properties:
- interrupts: Should contain phy interrupt
- fsl,anatop: phandle for anatop register, it is only for imx6 SoC
series
+
+ if (!of_property_read_u32(np, "fsl,tx-d-cal", &val) &&
+ val >= MXS_PHY_TX_D_CAL_MIN && val <= MXS_PHY_TX_D_CAL_MAX) {
+ /* scale to 4-bit value */
+ val = (MXS_PHY_TX_D_CAL_MAX - val) * 0xF
+ / (MXS_PHY_TX_D_CAL_MAX - MXS_PHY_TX_D_CAL_MIN);
+ mxs_phy->tx_reg_mask |= GM_USBPHY_TX_D_CAL(~0);
+ mxs_phy->tx_reg_set |= GM_USBPHY_TX_D_CAL(val);
+ }
+
I have tested "tx-d-cal", but it seems incorrect according to the xls you
have provided, would you please check it again or am I wrong?
Gah! You're right. Some of the D_CAL values need to be rounded up to
match the xls. And even then, the value for 86 still doesn't play nice.
I was really hoping to avoid using a table for these values.
The TXCALDP/DN values use a much simpler 1-to-1 scale across the 16
possible register values and so are unaffected by a similar issue. I
rechecked their numbers just to be sure.
The solution looks to be to scale D_CAL starting from 80 instead of
79. If you look at the xls listing, the jump from 79 to 83 is the
only time two adjacent register values result in a change greater
than 2% or 3%.
This will result in some code ugliness as the minimum allowed
percentage (79), per the Freescale document, and the point at which
we are scaling the percentage values to register values (80) are
different.
And, as mentioned before, the values will also have to be rounded up.
This quick shell code confirms that these sorts of calculations
match up with the values in the spreadsheet:
for d in 119 116 114 112 109 106 103 100 97 95 93 90 88 86 83 79; do
echo "$d="$(( ( (119-$d) * 0xf + (119-80)/2 ) / (119-80) ));
d=$((d+1)); done
I can't find any formula which would hit all of those same
percentages without rounding up.
Then, we had to use table for it. Besides, IC team confirms the default
value and the step for TXCAL45DP/DN are changed at next generation SoCs,
so I am wondering how we describe it at binding doc.
Which next gen SoC would this be? The MX7? The documentation for the
USB PHY in that reference manual is even sparser than the one for the
MX6 in regards to these register values.
The MX7 manual does still mention that HW_USBPHY_TX_TXCAL45DP and
HW_USBPHY_TX_TXCAL45DN should both be set to zero, but there is no
listing as to the location of these registers, let alone their
defaults/step values.
Do you know where we could get the default and step values for the TXCAL
registers on the new SoC? This information had to come from a Freescale
community thread for the MX6 since it wasn't defined clearly elsewhere.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
