From: Tim Harvey <tharvey@xxxxxxxxxxxxx>
The PLX USB2380 is a PCIe version of the NET2280 and behaves more like the
USB338x but without the USB3.0 superspeed support.
This was tested with g_ether, g_serial, g_mass_storage on a Gateworks
Ventana GW2383.
Cc: Justin DeFields <justindefields@xxxxxxxxx>
Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
Signed-off-by: Felipe Balbi <felipe.balbi@xxxxxxxxxxxxxxx>
---
drivers/usb/gadget/udc/Kconfig | 4 +++-
drivers/usb/gadget/udc/net2280.c | 51 +++++++++++++++++++++++-----------------
drivers/usb/gadget/udc/net2280.h | 1 +
3 files changed, 34 insertions(+), 22 deletions(-)
diff --git a/drivers/usb/gadget/udc/Kconfig b/drivers/usb/gadget/udc/Kconfig
index 7c289416f87d..658b8da60915 100644
--- a/drivers/usb/gadget/udc/Kconfig
+++ b/drivers/usb/gadget/udc/Kconfig
@@ -312,7 +312,7 @@ config USB_NET2272_DMA
If unsure, say "N" here. The driver works fine in PIO mode.
config USB_NET2280
- tristate "NetChip 228x / PLX USB338x"
+ tristate "NetChip NET228x / PLX USB3x8x"
depends on PCI
help
NetChip 2280 / 2282 is a PCI based USB peripheral controller which
@@ -322,6 +322,8 @@ config USB_NET2280
(for control transfers) and several endpoints with dedicated
functions.
+ PLX 2380 is a PCIe version of the PLX 2380.
+
PLX 3380 / 3382 is a PCIe based USB peripheral controller which
supports full, high speed USB 2.0 and super speed USB 3.0
data transfers.
diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c
index c894b94b234b..614ab951a4ae 100644
--- a/drivers/usb/gadget/udc/net2280.c
+++ b/drivers/usb/gadget/udc/net2280.c
@@ -211,7 +211,7 @@ net2280_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
goto print_err;
}
- if (dev->quirks & PLX_SUPERSPEED) {
+ if (dev->quirks & PLX_PCIE) {
if ((desc->bEndpointAddress & 0x0f) >= 0x0c) {
ret = -EDOM;
goto print_err;
@@ -245,7 +245,7 @@ net2280_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
/* set type, direction, address; reset fifo counters */
writel(BIT(FIFO_FLUSH), &ep->regs->ep_stat);
- if ((dev->quirks & PLX_SUPERSPEED) && dev->enhanced_mode) {
+ if ((dev->quirks & PLX_PCIE) && dev->enhanced_mode) {
tmp = readl(&ep->cfg->ep_cfg);
/* If USB ep number doesn't match hardware ep number */
if ((tmp & 0xf) != usb_endpoint_num(desc)) {
@@ -316,7 +316,7 @@ net2280_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
BIT(CLEAR_NAK_OUT_PACKETS_MODE), &ep->regs->ep_rsp);
}
- if (dev->quirks & PLX_SUPERSPEED)
+ if (dev->quirks & PLX_PCIE)
ep_clear_seqnum(ep);
writel(tmp, &ep->cfg->ep_cfg);
@@ -527,7 +527,7 @@ static int net2280_disable(struct usb_ep *_ep)
spin_lock_irqsave(&ep->dev->lock, flags);
nuke(ep);
- if (ep->dev->quirks & PLX_SUPERSPEED)
+ if (ep->dev->quirks & PLX_PCIE)
ep_reset_338x(ep->dev->regs, ep);
else
ep_reset_228x(ep->dev->regs, ep);
@@ -862,7 +862,7 @@ static void start_queue(struct net2280_ep *ep, u32 dmactl, u32 td_dma)
writel(readl(&dma->dmastat), &dma->dmastat);
writel(td_dma, &dma->dmadesc);
- if (ep->dev->quirks & PLX_SUPERSPEED)
+ if (ep->dev->quirks & PLX_PCIE)
dmactl |= BIT(DMA_REQUEST_OUTSTANDING);
writel(dmactl, &dma->dmactl);
@@ -1046,7 +1046,7 @@ net2280_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
/* kickstart this i/o queue? */
if (list_empty(&ep->queue) && !ep->stopped &&
- !((dev->quirks & PLX_SUPERSPEED) && ep->dma &&
+ !((dev->quirks & PLX_PCIE) && ep->dma &&
(readl(&ep->regs->ep_rsp) & BIT(CLEAR_ENDPOINT_HALT)))) {
/* use DMA if the endpoint supports it, else pio */
@@ -1169,7 +1169,7 @@ static void scan_dma_completions(struct net2280_ep *ep)
break;
} else if (!ep->is_in &&
(req->req.length % ep->ep.maxpacket) &&
- !(ep->dev->quirks & PLX_SUPERSPEED)) {
+ !(ep->dev->quirks & PLX_PCIE)) {
tmp = readl(&ep->regs->ep_stat);
/* AVOID TROUBLE HERE by not issuing short reads from
@@ -1367,7 +1367,7 @@ net2280_set_halt_and_wedge(struct usb_ep *_ep, int value, int wedged)
ep->wedged = 1;
} else {
clear_halt(ep);
- if (ep->dev->quirks & PLX_SUPERSPEED &&
+ if (ep->dev->quirks & PLX_PCIE &&
!list_empty(&ep->queue) && ep->td_dma)
restart_dma(ep);
ep->wedged = 0;
@@ -2394,7 +2394,7 @@ static int net2280_start(struct usb_gadget *_gadget,
*/
net2280_led_active(dev, 1);
- if ((dev->quirks & PLX_SUPERSPEED) && !dev->bug7734_patched)
+ if ((dev->quirks & PLX_PCIE) && !dev->bug7734_patched)
defect7374_enable_data_eps_zero(dev);
ep0_start(dev);
@@ -3063,7 +3063,7 @@ static void handle_stat0_irqs(struct net2280 *dev, u32 stat)
}
ep->stopped = 0;
dev->protocol_stall = 0;
- if (!(dev->quirks & PLX_SUPERSPEED)) {
+ if (!(dev->quirks & PLX_PCIE)) {
if (ep->dev->quirks & PLX_2280)
tmp = BIT(FIFO_OVERFLOW) |
BIT(FIFO_UNDERFLOW);
@@ -3090,7 +3090,7 @@ static void handle_stat0_irqs(struct net2280 *dev, u32 stat)
cpu_to_le32s(&u.raw[0]);
cpu_to_le32s(&u.raw[1]);
- if ((dev->quirks & PLX_SUPERSPEED) && !dev->bug7734_patched)
+ if ((dev->quirks & PLX_PCIE) && !dev->bug7734_patched)
defect7374_workaround(dev, u.r);
tmp = 0;
@@ -3173,7 +3173,7 @@ static void handle_stat0_irqs(struct net2280 *dev, u32 stat)
} else {
ep_vdbg(dev, "%s clear halt\n", e->ep.name);
clear_halt(e);
- if ((ep->dev->quirks & PLX_SUPERSPEED) &&
+ if ((ep->dev->quirks & PLX_PCIE) &&
!list_empty(&e->queue) && e->td_dma)
restart_dma(e);
}
@@ -3195,7 +3195,7 @@ static void handle_stat0_irqs(struct net2280 *dev, u32 stat)
if (e->ep.name == ep0name)
goto do_stall;
set_halt(e);
- if ((dev->quirks & PLX_SUPERSPEED) && e->dma)
+ if ((dev->quirks & PLX_PCIE) && e->dma)
abort_dma(e);
allow_status(ep);
ep_vdbg(dev, "%s set halt\n", ep->ep.name);
@@ -3234,7 +3234,7 @@ do_stall:
#undef w_length
next_endpoints:
- if ((dev->quirks & PLX_SUPERSPEED) && dev->enhanced_mode) {
+ if ((dev->quirks & PLX_PCIE) && dev->enhanced_mode) {
u32 mask = (BIT(ENDPOINT_0_INTERRUPT) |
USB3380_IRQSTAT0_EP_INTR_MASK_IN |
USB3380_IRQSTAT0_EP_INTR_MASK_OUT);
@@ -3399,7 +3399,7 @@ __acquires(dev->lock)
writel(tmp, &dma->dmastat);
/* dma sync*/
- if (dev->quirks & PLX_SUPERSPEED) {
+ if (dev->quirks & PLX_PCIE) {
u32 r_dmacount = readl(&dma->dmacount);
if (!ep->is_in && (r_dmacount & 0x00FFFFFF) &&
(tmp & BIT(DMA_TRANSACTION_DONE_INTERRUPT)))
@@ -3468,7 +3468,7 @@ static irqreturn_t net2280_irq(int irq, void *_dev)
/* control requests and PIO */
handle_stat0_irqs(dev, readl(&dev->regs->irqstat0));
- if (dev->quirks & PLX_SUPERSPEED) {
+ if (dev->quirks & PLX_PCIE) {
/* re-enable interrupt to trigger any possible new interrupt */
u32 pciirqenb1 = readl(&dev->regs->pciirqenb1);
writel(pciirqenb1 & 0x7FFFFFFF, &dev->regs->pciirqenb1);
@@ -3513,7 +3513,7 @@ static void net2280_remove(struct pci_dev *pdev)
}
if (dev->got_irq)
free_irq(pdev->irq, dev);
- if (dev->quirks & PLX_SUPERSPEED)
+ if (dev->quirks & PLX_PCIE)
pci_disable_msi(pdev);
if (dev->regs)
iounmap(dev->regs);
@@ -3593,7 +3593,7 @@ static int net2280_probe(struct pci_dev *pdev, const struct pci_device_id *id)
dev->dep = (struct net2280_dep_regs __iomem *) (base + 0x0200);
dev->epregs = (struct net2280_ep_regs __iomem *) (base + 0x0300);
- if (dev->quirks & PLX_SUPERSPEED) {
+ if (dev->quirks & PLX_PCIE) {
u32 fsmvalue;
u32 usbstat;
dev->usb_ext = (struct usb338x_usb_ext_regs __iomem *)
@@ -3637,7 +3637,7 @@ static int net2280_probe(struct pci_dev *pdev, const struct pci_device_id *id)
goto done;
}
- if (dev->quirks & PLX_SUPERSPEED)
+ if (dev->quirks & PLX_PCIE)
if (pci_enable_msi(pdev))
ep_err(dev, "Failed to enable MSI mode\n");
@@ -3755,10 +3755,19 @@ static const struct pci_device_id pci_ids[] = { {
.class = PCI_CLASS_SERIAL_USB_DEVICE,
.class_mask = ~0,
.vendor = PCI_VENDOR_ID_PLX,
+ .device = 0x2380,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .driver_data = PLX_PCIE,
+ },
+ {
+ .class = ((PCI_CLASS_SERIAL_USB << 8) | 0xfe),
+ .class_mask = ~0,
+ .vendor = PCI_VENDOR_ID_PLX,
.device = 0x3380,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
- .driver_data = PLX_SUPERSPEED,
+ .driver_data = PLX_PCIE | PLX_SUPERSPEED,
},
{
.class = PCI_CLASS_SERIAL_USB_DEVICE,
@@ -3767,7 +3776,7 @@ static const struct pci_device_id pci_ids[] = { {
.device = 0x3382,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
- .driver_data = PLX_SUPERSPEED,
+ .driver_data = PLX_PCIE | PLX_SUPERSPEED,
},
{ /* end: all zeroes */ }
};
diff --git a/drivers/usb/gadget/udc/net2280.h b/drivers/usb/gadget/udc/net2280.h
index 0d32052bf16f..2736a95751c3 100644
--- a/drivers/usb/gadget/udc/net2280.h
+++ b/drivers/usb/gadget/udc/net2280.h
@@ -47,6 +47,7 @@ set_idx_reg(struct net2280_regs __iomem *regs, u32 index, u32 value)
#define PLX_LEGACY BIT(0)
#define PLX_2280 BIT(1)
#define PLX_SUPERSPEED BIT(2)
+#define PLX_PCIE BIT(3)
#define REG_DIAG 0x0
#define RETRY_COUNTER 16
--
2.8.3
---------------------------------------------------------------------
Intel Finland Oy
Registered Address: PL 281, 00181 Helsinki
Business Identity Code: 0357606 - 4
Domiciled in Helsinki
This e-mail and any attachments may contain confidential material for
the sole use of the intended recipient(s). Any review or distribution
by others is strictly prohibited. If you are not the intended
recipient, please contact the sender and delete all copies.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
