[PATCH 002/123] USB: another unusual_devs entry for another bad Argosy storage device

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Nguyen Anh Quynh <aquynh@xxxxxxxxx>

I have another Argosy USB storage device, which has the same problem
with the Argosy USB storage device already fixed in 2.6.27.7. But this
device has another product ID (840:84), so this patch adds a new entry
into unusual_devs to fix the mount problem.

I enclose here two patches: one against 2.6.27.8, and another against
the latest linus-git tree.


The information about the Argosy device is like below:

#lsusb -v -d 840:84
Bus 005 Device 005: ID 0840:0084 Argosy Research, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0840 Argosy Research, Inc.
  idProduct          0x0084
  bcdDevice            0.01
  iManufacturer           1 Generic
  iProduct                2 USB 2.0 Storage Device
  iSerial                 3 8400000000002549
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xc0
      Self Powered
    MaxPower                2mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Before the patch, dmesg returns a lot of information like below (my
dmesg is overflown):
....
[  138.833390] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
[  138.877631] sd 7:0:0:0: [sdb] Sense Key : No Sense [current]
[  138.877643] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
[  138.921906] sd 7:0:0:0: [sdb] Sense Key : No Sense [current]
[  138.921923] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
....

After the fix, dmesg returns below information:
....
usb 5-1: new high speed USB device using ehci_hcd and address 5
usb 5-1: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 7:0:0:0: Direct-Access     HTS54808 0M9AT00          MG4O PQ: 0 ANSI: 0
sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 7:0:0:0: [sdb] Attached SCSI disk
sd 7:0:0:0: Attached scsi generic sg1 type 0
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.

Cc: Kuniyasu Suzaki <k.suzaki@xxxxxxxxxx>
Signed-off-by: Nguyen Anh Quynh <aquynh@xxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
Cc: stable <stable@xxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxx>
---
 drivers/usb/storage/unusual_devs.h |    7 +++++++
 1 files changed, 7 insertions(+), 0 deletions(-)

diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index a54212f..af34504 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -1320,6 +1320,13 @@ UNUSUAL_DEV( 0x0840, 0x0082, 0x0001, 0x0001,
 		US_SC_DEVICE, US_PR_DEVICE, NULL,
 		US_FL_FIX_CAPACITY),
 
+/* Reported and patched by Nguyen Anh Quynh <aquynh@xxxxxxxxx> */
+UNUSUAL_DEV( 0x0840, 0x0084, 0x0001, 0x0001,
+		"Argosy",
+		"Storage",
+		US_SC_DEVICE, US_PR_DEVICE, NULL,
+		US_FL_FIX_CAPACITY),
+
 /* Entry and supporting patch by Theodore Kilgore <kilgota@xxxxxxxxxx>.
  * Flag will support Bulk devices which use a standards-violating 32-byte
  * Command Block Wrapper. Here, the "DC2MEGA" cameras (several brands) with
-- 
1.6.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux