Hello.
On 12/18/2015 4:14 AM, Chanwoo Choi wrote:
Except for just one comment below, Looks good to me.
Acked-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
I'll wait for a few days to get the review from DT maintainer
before applying it on extcon-next branch.
On 2015년 12월 18일 07:47, Sergei Shtylyov wrote:
Maxim Integrated MAX3355E chip integrates a charge pump and comparators to
enable a system with an integrated USB OTG dual-role transceiver to
function as an USB OTG dual-role device. In addition to sensing/controlling
Vbus, the chip also passes thru the ID signal from the USB OTG connector.
On some Renesas boards, this signal is just fed into the SoC thru a GPIO
pin -- there's no real OTG controller, only host and gadget USB controllers
sharing the same USB bus; however, we'd like to allow host or gadget
drivers to be loaded depending on the cable type, hence the need for the
MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs
(however, we aren't currently interested in them), the OFFVBUS# signal is
controlled by the host controllers, there's also the SHDN# signal wired to
a GPIO, it should be driven high for the normal operation.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@xxxxxxxxxxxxxxxxxx>
---
The patch is against the 'extcon-next' branch of the 'extcon.git' repo.
Changes in version 4:
- stopped calling kstrdup() for the device name;
- removed unneeded 'owner' field initializer;
- moved devm_extcon_allocate() call further down in the probe() method;
- extended the driver copyright;
- indented the continuation lines in the binding document.
Changes in version 3:
- reformatted the change log.
Changes in version 2:
- added the USB gadget cable support;
- added the remove() driver method which drives SHDN# GPIO low to save power;
- dropped vendor prefix from the ID GPIO property name;
- changed the GPIO property name suffix to "-gpios";
- switched to usign extcon_set_cable_state_() API;
- switched to using the gpiod/sleeping 'gpiolib' APIs;
- addded error messages to max3355_probe();
- added IRQF_NO_SUSPEND flasg to the devm_request_threaded_irq() call;
- renamed 'ret' variable to 'err' in max3355_probe();
- expanded the Kconfig entry help text;
- added vendor name to the patch summary, the bindings document, the Kconfig
entry, the driver heading comment, the module description, and the change log;
- fixed up and reformatted the change log.
Documentation/devicetree/bindings/extcon/extcon-max3355.txt | 21 +
drivers/extcon/Kconfig | 8
drivers/extcon/Makefile | 1
drivers/extcon/extcon-max3355.c | 151 ++++++++++++
4 files changed, 181 insertions(+)
Index: extcon/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
===================================================================
--- /dev/null
+++ extcon/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
@@ -0,0 +1,21 @@
+Maxim Integrated MAX3355 USB OTG chip
+-------------------------------------
+
+MAX3355 integrates a charge pump and comparators to enable a system with an
+integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
+device.
+
+Required properties:
+- compatible: should be "maxim,max3355";
+- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin
+ connected to the MAX3355's SHDN# pin;
+- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin
+ connected to the MAX3355's ID_OUT pin.
+
+Example (Koelsch board):
You mean that "koelsch" board might be arch/arm/boot/dts/r8a7791-koelsch.dts.
But, the max3355 dt node isn't really included in r8a7791-koelsch.dts.
Of course, I couldn't post the device tree patch before the binding was
accepted.
I recommend that you add the accurate information because the wrong
info causes the confusion. So, I'd like you to change it as following:
"Example (Koelsch board):" -> "Example:"
After adding the max3355 dt node to Koelsch board on separate patch,
you modify this documentation for real usage case of max3355 dt node.
No dire need to modify the documentation then. Should I still repost?
[...]
Thanks,
Chanwoo Choi
MBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
