Deprecate using phy-omap-control driver to power on/off the PHY and use *syscon* framework to do the same. Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx> --- Documentation/devicetree/bindings/phy/ti-phy.txt | 10 ++- drivers/phy/phy-ti-pipe3.c | 90 ++++++++++++++++++---- 2 files changed, 85 insertions(+), 15 deletions(-) diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index 9cf9446..e06f980 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -77,8 +77,6 @@ Required properties: * "div-clk" - apll clock Optional properties: - - ctrl-module : phandle of the control module used by PHY driver to power on - the PHY. - id: If there are multiple instance of the same type, in order to differentiate between each instance "id" can be used (e.g., multi-lane PCIe PHY). If "id" is not provided, it is set to default value of '1'. @@ -86,6 +84,14 @@ Optional properties: CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0 register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy. +Deprecated properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +Recommended properies: + - syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. + This is usually a subnode of ocp2scp to which it is connected. usb3phy@4a084400 { diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c index 0ce4194..bc03625 100644 --- a/drivers/phy/phy-ti-pipe3.c +++ b/drivers/phy/phy-ti-pipe3.c @@ -56,6 +56,15 @@ #define SATA_PLL_SOFT_RESET BIT(18) +#define PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000 +#define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 14 + +#define PIPE3_PHY_PWRCTL_CLK_FREQ_MASK 0xFFC00000 +#define PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT 22 + +#define PIPE3_PHY_TX_RX_POWERON 0x3 +#define PIPE3_PHY_TX_RX_POWEROFF 0x0 + /* * This is an Empirical value that works, need to confirm the actual * value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status @@ -86,8 +95,10 @@ struct ti_pipe3 { struct clk *refclk; struct clk *div_clk; struct pipe3_dpll_map *dpll_map; + struct regmap *phy_power_syscon; /* ctrl. reg. acces */ struct regmap *dpll_reset_syscon; /* ctrl. reg. acces */ unsigned int dpll_reset_reg; /* reg. index within syscon */ + unsigned int power_reg; /* power reg. index within syscon */ bool sata_refclk_enabled; }; @@ -144,18 +155,53 @@ static void ti_pipe3_disable_clocks(struct ti_pipe3 *phy); static int ti_pipe3_power_off(struct phy *x) { + u32 val; + int ret; struct ti_pipe3 *phy = phy_get_drvdata(x); - omap_control_phy_power(phy->control_dev, 0); + if (phy->phy_power_syscon) { + val = PIPE3_PHY_TX_RX_POWEROFF << + PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT; + + ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg, + PIPE3_PHY_PWRCTL_CLK_CMD_MASK, val); + if (ret < 0) + return ret; + } else { + omap_control_phy_power(phy->control_dev, 0); + } return 0; } static int ti_pipe3_power_on(struct phy *x) { + u32 val; + u32 mask; + int ret; + unsigned long rate; struct ti_pipe3 *phy = phy_get_drvdata(x); - omap_control_phy_power(phy->control_dev, 1); + if (phy->phy_power_syscon) { + rate = clk_get_rate(phy->sys_clk); + if (!rate) { + dev_err(phy->dev, "Invalid clock rate\n"); + return -EINVAL; + } + rate = rate / 1000000; + mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK | + OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK; + val = PIPE3_PHY_TX_RX_POWERON << + PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT; + val |= rate << OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT; + + ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg, + mask, val); + if (ret < 0) + return ret; + } else { + omap_control_phy_power(phy->control_dev, 1); + } return 0; } @@ -334,7 +380,8 @@ static int ti_pipe3_get_clk(struct ti_pipe3 *phy) phy->wkupclk = ERR_PTR(-ENODEV); } - if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie")) { + if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie") || + phy->phy_power_syscon) { phy->sys_clk = devm_clk_get(dev, "sysclk"); if (IS_ERR(phy->sys_clk)) { dev_err(dev, "unable to get sysclk\n"); @@ -383,19 +430,36 @@ static int ti_pipe3_get_sysctrl(struct ti_pipe3 *phy) struct device_node *control_node; struct platform_device *control_pdev; - control_node = of_parse_phandle(node, "ctrl-module", 0); - if (!control_node) { - dev_err(dev, "Failed to get control device phandle\n"); - return -EINVAL; + phy->phy_power_syscon = syscon_regmap_lookup_by_phandle(node, + "syscon-phy-power"); + if (IS_ERR(phy->phy_power_syscon)) { + dev_dbg(dev, + "can't get syscon-phy-power, using control device\n"); + phy->phy_power_syscon = NULL; + } else { + if (of_property_read_u32_index(node, + "syscon-phy-power", 1, + &phy->power_reg)) { + dev_err(dev, "couldn't get power reg. offset\n"); + return -EINVAL; + } } - control_pdev = of_find_device_by_node(control_node); - if (!control_pdev) { - dev_err(dev, "Failed to get control device\n"); - return -EINVAL; - } + if (!phy->phy_power_syscon) { + control_node = of_parse_phandle(node, "ctrl-module", 0); + if (!control_node) { + dev_err(dev, "Failed to get control device phandle\n"); + return -EINVAL; + } - phy->control_dev = &control_pdev->dev; + control_pdev = of_find_device_by_node(control_node); + if (!control_pdev) { + dev_err(dev, "Failed to get control device\n"); + return -EINVAL; + } + + phy->control_dev = &control_pdev->dev; + } if (of_device_is_compatible(node, "ti,phy-pipe3-sata")) { phy->dpll_reset_syscon = syscon_regmap_lookup_by_phandle(node, -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html