If a xhci controller does not provide a protocol speed ID (PSI) table, a
default one should be used instead. Add the default values to the
SuperSpeedPlus device capability. Overwrite the default ones if a PSI table
exists. See xHCI 1.1 sectio 7.2.2.1.1 for more info
Signed-off-by: Mathias Nyman <mathias.nyman@xxxxxxxxxxxxxxx>
---
drivers/usb/host/xhci-hub.c | 27 ++++++++++++++++++---------
1 file changed, 18 insertions(+), 9 deletions(-)
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index 0863d8a..2c26ab50 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -50,14 +50,18 @@ static u8 usb_bos_descriptor [] = {
0x00, /* bU1DevExitLat, set later. */
0x00, 0x00, /* __le16 bU2DevExitLat, set later. */
/* Second device capability, SuperSpeedPlus */
- 0x0c, /* bLength 12, will be adjusted later */
+ 0x1c, /* bLength 28, will be adjusted later */
USB_DT_DEVICE_CAPABILITY, /* Device Capability */
USB_SSP_CAP_TYPE, /* bDevCapabilityType SUPERSPEED_PLUS */
0x00, /* bReserved 0 */
- 0x00, 0x00, 0x00, 0x00, /* bmAttributes, get from xhci psic */
- 0x00, 0x00, /* wFunctionalitySupport */
+ 0x23, 0x00, 0x00, 0x00, /* bmAttributes, SSAC=3 SSIC=1 */
+ 0x01, 0x00, /* wFunctionalitySupport */
0x00, 0x00, /* wReserved 0 */
- /* Sublink Speed Attributes are added in xhci_create_usb3_bos_desc() */
+ /* Default Sublink Speed Attributes, overwrite if custom PSI exists */
+ 0x34, 0x00, 0x05, 0x00, /* 5Gbps, symmetric, rx, ID = 4 */
+ 0xb4, 0x00, 0x05, 0x00, /* 5Gbps, symmetric, tx, ID = 4 */
+ 0x35, 0x40, 0x0a, 0x00, /* 10Gbps, SSP, symmetric, rx, ID = 5 */
+ 0xb5, 0x40, 0x0a, 0x00, /* 10Gbps, SSP, symmetric, tx, ID = 5 */
};
static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
@@ -72,10 +76,14 @@ static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
ssp_cap_size = sizeof(usb_bos_descriptor) - desc_size;
/* does xhci support USB 3.1 Enhanced SuperSpeed */
- if (xhci->usb3_rhub.min_rev >= 0x01 && xhci->usb3_rhub.psi_uid_count) {
- /* two SSA entries for each unique PSI ID, one RX and one TX */
- ssa_count = xhci->usb3_rhub.psi_uid_count * 2;
- ssa_size = ssa_count * sizeof(u32);
+ if (xhci->usb3_rhub.min_rev >= 0x01) {
+ /* does xhci provide a PSI table for SSA speed attributes? */
+ if (xhci->usb3_rhub.psi_count) {
+ /* two SSA entries for each unique PSI ID, RX and TX */
+ ssa_count = xhci->usb3_rhub.psi_uid_count * 2;
+ ssa_size = ssa_count * sizeof(u32);
+ ssp_cap_size -= 16; /* skip copying the default SSA */
+ }
desc_size += ssp_cap_size;
usb3_1 = true;
}
@@ -102,7 +110,8 @@ static int xhci_create_usb3_bos_desc(struct xhci_hcd *xhci, char *buf,
put_unaligned_le16(HCS_U2_LATENCY(temp), &buf[13]);
}
- if (usb3_1) {
+ /* If PSI table exists, add the custom speed attributes from it */
+ if (usb3_1 && xhci->usb3_rhub.psi_count) {
u32 ssp_cap_base, bm_attrib, psi;
int offset;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
