Hi Peter, > -----Original Message----- > From: Peter Chen [mailto:peter.chen@xxxxxxxxxxxxx] > Sent: Thursday, September 24, 2015 2:41 PM > To: Subbaraya Sundeep Bhatta > Cc: balbi@xxxxxx; devicetree@xxxxxxxxxxxxxxx; kishon@xxxxxx; > gregkh@xxxxxxxxxxxxxxxxxxx; linux-usb@xxxxxxxxxxxxxxx; linux- > kernel@xxxxxxxxxxxxxxx; Punnaiah Choudary Kalluri; Subbaraya Sundeep Bhatta; > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > Subject: Re: [RFC PATCH 1/2] usb: doc: Add bindings for ULPI platform driver > > On Wed, Sep 23, 2015 at 06:24:01PM +0530, Subbaraya Sundeep Bhatta > wrote: > > This patch adds binding doc info for generic ULPI PHYs platform > > driver. > > > > Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xxxxxxxxxx> > > --- > > .../devicetree/bindings/usb/ulpi-platform-phy.txt | 34 > ++++++++++++++++++++ > > 1 files changed, 34 insertions(+), 0 deletions(-) create mode 100644 > > Documentation/devicetree/bindings/usb/ulpi-platform-phy.txt > > > > diff --git > > a/Documentation/devicetree/bindings/usb/ulpi-platform-phy.txt > > b/Documentation/devicetree/bindings/usb/ulpi-platform-phy.txt > > new file mode 100644 > > index 0000000..7b8cbb4 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/usb/ulpi-platform-phy.txt > > @@ -0,0 +1,34 @@ > > +Platform driver for generic ULPI PHYs > > + > > +Required properties: > > +- compatible : Should be "ulpi-phy" > > +- reg : Physical base address and size of the USB > > + controller registers map to which this PHY > > + is connected. > > +- view-port : Should contain viewport register offset of the > > + USB controller to which this PHY is connected Optional > > +properties: > > +- drv-vbus : required if turning VBUS on/off has to be driven > > + by writing to PHY. This feature depends on board > > + design. > > + > > +Example: > > +Below example shows the PHY binding for Chipidea USB controller which > > +has ulpi viewport register at 0x0170 > > + > > + usb_phy0: phy0 { > > + compatible = "ulpi-phy"; > > + reg = <0xe0002000 0x1000>; > > + view-port = <0x0170>; > > + drv-vbus; > > + }; > > + > > + usb0: usb@e0002000 { > > + compatible = "chipidea,usb2"; > > + interrupt-parent = <&intc>; > > + interrupts = <0 21 4>; > > + reg = <0xe0002000 0x1000>; > > Although just call devm_ioremap twice for the same register region does not > cause any errors, I am not sure if it will has other potential problems. Cc: arm > list. Yes Peter I was also in doubt to call devm_ioremap twice for same register region. devm_ioremap_resource complained hence modified to devm_ioremap. Thanks for adding arm-list. Sundeep > > > + phy_type = "ulpi"; > > + dr_mode = "host"; > > + usb-phy = <&usb_phy0>; > > + }; > > -- > > 1.7.1 > > > > -- > > Best Regards, > Peter Chen -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
