From: Tomer Barletz <barletz@xxxxxxxxx>
xhci_pme_quirk() is only used when CONFIG_PM is defined.
Compiling a kernel without PM complains about this function
[reworded commit message -Mathias]
Cc: <stable@xxxxxxxxxxxxxxx>
Signed-off-by: Tomer Barletz <barletz@xxxxxxxxx>
Signed-off-by: Mathias Nyman <mathias.nyman@xxxxxxxxxxxxxxx>
---
drivers/usb/host/xhci-pci.c | 90 ++++++++++++++++++++++-----------------------
1 file changed, 45 insertions(+), 45 deletions(-)
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index 5590eac..c79d336 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -180,51 +180,6 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
"QUIRK: Resetting on resume");
}
-/*
- * In some Intel xHCI controllers, in order to get D3 working,
- * through a vendor specific SSIC CONFIG register at offset 0x883c,
- * SSIC PORT need to be marked as "unused" before putting xHCI
- * into D3. After D3 exit, the SSIC port need to be marked as "used".
- * Without this change, xHCI might not enter D3 state.
- * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
- * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
- */
-static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
-{
- struct xhci_hcd *xhci = hcd_to_xhci(hcd);
- struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
- u32 val;
- void __iomem *reg;
-
- if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
- pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
-
- reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2;
-
- /* Notify SSIC that SSIC profile programming is not done */
- val = readl(reg) & ~PROG_DONE;
- writel(val, reg);
-
- /* Mark SSIC port as unused(suspend) or used(resume) */
- val = readl(reg);
- if (suspend)
- val |= SSIC_PORT_UNUSED;
- else
- val &= ~SSIC_PORT_UNUSED;
- writel(val, reg);
-
- /* Notify SSIC that SSIC profile programming is done */
- val = readl(reg) | PROG_DONE;
- writel(val, reg);
- readl(reg);
- }
-
- reg = (void __iomem *) xhci->cap_regs + 0x80a4;
- val = readl(reg);
- writel(val | BIT(28), reg);
- readl(reg);
-}
-
#ifdef CONFIG_ACPI
static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev)
{
@@ -345,6 +300,51 @@ static void xhci_pci_remove(struct pci_dev *dev)
}
#ifdef CONFIG_PM
+/*
+ * In some Intel xHCI controllers, in order to get D3 working,
+ * through a vendor specific SSIC CONFIG register at offset 0x883c,
+ * SSIC PORT need to be marked as "unused" before putting xHCI
+ * into D3. After D3 exit, the SSIC port need to be marked as "used".
+ * Without this change, xHCI might not enter D3 state.
+ * Make sure PME works on some Intel xHCI controllers by writing 1 to clear
+ * the Internal PME flag bit in vendor specific PMCTRL register at offset 0x80a4
+ */
+static void xhci_pme_quirk(struct usb_hcd *hcd, bool suspend)
+{
+ struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
+ u32 val;
+ void __iomem *reg;
+
+ if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+ pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
+
+ reg = (void __iomem *) xhci->cap_regs + PORT2_SSIC_CONFIG_REG2;
+
+ /* Notify SSIC that SSIC profile programming is not done */
+ val = readl(reg) & ~PROG_DONE;
+ writel(val, reg);
+
+ /* Mark SSIC port as unused(suspend) or used(resume) */
+ val = readl(reg);
+ if (suspend)
+ val |= SSIC_PORT_UNUSED;
+ else
+ val &= ~SSIC_PORT_UNUSED;
+ writel(val, reg);
+
+ /* Notify SSIC that SSIC profile programming is done */
+ val = readl(reg) | PROG_DONE;
+ writel(val, reg);
+ readl(reg);
+ }
+
+ reg = (void __iomem *) xhci->cap_regs + 0x80a4;
+ val = readl(reg);
+ writel(val | BIT(28), reg);
+ readl(reg);
+}
+
static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
