ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@xxxxxxxxxxxxx>
---
drivers/usb/chipidea/core.c | 16 ++++++++++++++++
include/linux/usb/chipidea.h | 2 ++
2 files changed, 18 insertions(+)
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 89c79d0..dd3d10a 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -425,6 +425,9 @@ void ci_platform_configure(struct ci_hdrc *ci)
if (ci->platdata->flags & CI_HDRC_SET_NON_ZERO_TTHA)
hw_write(ci, OP_TTCTRL, TTCTRL_TTHA_MASK, TTCTRL_TTHA);
+
+ hw_write(ci, OP_USBCMD, 0xff0000, ci->platdata->itc_setting << 16);
+
}
/**
@@ -576,6 +579,8 @@ static irqreturn_t ci_irq(int irq, void *data)
static int ci_get_platdata(struct device *dev,
struct ci_hdrc_platform_data *platdata)
{
+ int ret;
+
if (!platdata->phy_mode)
platdata->phy_mode = of_usb_get_phy_mode(dev->of_node);
@@ -607,6 +612,17 @@ static int ci_get_platdata(struct device *dev,
if (of_usb_get_maximum_speed(dev->of_node) == USB_SPEED_FULL)
platdata->flags |= CI_HDRC_FORCE_FULLSPEED;
+ platdata->itc_setting = 1;
+ if (of_find_property(dev->of_node, "itc-setting", NULL)) {
+ ret = of_property_read_u32(dev->of_node, "itc-setting",
+ &platdata->itc_setting);
+ if (ret) {
+ dev_err(dev,
+ "failed to get itc-setting value\n");
+ return ret;
+ }
+ }
+
return 0;
}
diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
index d1e1285..1c5d776 100644
--- a/include/linux/usb/chipidea.h
+++ b/include/linux/usb/chipidea.h
@@ -36,6 +36,8 @@ struct ci_hdrc_platform_data {
void (*notify_event) (struct ci_hdrc *ci, unsigned event);
struct regulator *reg_vbus;
bool tpl_support;
+ /* interrupt threshold setting */
+ u32 itc_setting;
};
/* Default offset of capability registers */
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
