Hi,
We have designed a h/w system with the Renesas USB 3.0 upd7202 controller.
We are seeing that sometimes xhci initialization fails with a "can't
setup" error message.
As a result lsusb doesn't report the USB3.0 ports.
Adding traces to the kernel we could see that this is happening in
xhci_reset() --> xhci_handshake() sequence, where xhci_handshake exits
in time out. (I tried to increase the time out value by 10 times..it
didn't help)
This is happening on Centos 6.5 using Centos kernel
2.6.32-431.el6.x86_64. Now I know it is very old and I apologize. But
I have limited access to the system, and that is what it is configured
with currently. But we had the opportunity to quickly load latest
fedora 22 (kernel is 4.0) and the same problem happens.
Here is what dmesg says:
uhci_hcd: USB Universal Host Controller Interface driver
xhci_hcd 0000:94:00.0: PCI INT A -> GSI 64 (level, low) -> IRQ 64
xhci_hcd 0000:94:00.0: setting latency timer to 64
xhci_hcd 0000:94:00.0: xHCI Host Controller
xhci_hcd 0000:94:00.0: new USB bus registered, assigned bus number 15
usb usb13: bus auto-suspend
xhci_hcd 0000:94:00.0: // Halt the HC
xhci_hcd 0000:94:00.0: Resetting HCD
xhci_hcd 0000:94:00.0: // Reset the HC
usb usb14: bus auto-suspend
(xhci_handshake: exits in time out)
xhci_hcd 0000:94:00.0: can't setup
xhci_hcd 0000:94:00.0: USB bus 15 deregistered
xhci_hcd 0000:94:00.0: PCI INT A disabled
xhci_hcd 0000:94:00.0: init 0000:94:00.0 fail, -110
xhci_hcd: probe of 0000:94:00.0 failed with error -110
As you can see for below, the PCI-e hierarchy includes a
PEX8624-->PEX8606- (OPTICAL LINK)->PEX8509-->UPD7202.
The upd7202 is "remote". There is a optical link between the 8606 and the 8509.
The upd7202 is located in a remote enclosure that has its own power
supply. That means it doesn't get powered at the same time the main
PCI-e fabric is powered. This is probably a key factor in the error.
84:08.0 PCI bridge: PLX Technology, Inc. PEX 8624 24-lane, 6-Port
PCI Express Gen 2 (5.0 GT/s) Switch [ExpressLane] (rev bb)
8e:00.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port
PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
8f:07.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6
Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba)
92:00.0 PCI bridge: PLX Technology, Inc. PEX 8509 8-lane,
8-port PCI Express Switch (rev aa)
93:01.0 PCI bridge: PLX Technology, Inc. PEX 8509 8-lane,
8-port PCI Express Switch (rev aa)
94:00.0 USB controller: Renesas Technology Corp.
uPD720202 USB 3.0 Host Controller (rev 02)
Here some info based on lspci:
# lspci -s 8f:07.0 -vvv
8f:07.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI
Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=8f, secondary=92, subordinate=9a, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: faf00000-fb5fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000fee00338 Data: 0000
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #7, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <2us, L1 <4us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk-
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #119, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-,
OBFF Not Supported ARIFwd+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8606 6
Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch
Capabilities: [100 v1] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [148 v1] Virtual Channel
Caps: LPEVC=1 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=1 ArbSelect=Fixed TC/VC=00
Status: NegoPending+ InProgress-
Capabilities: [520 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+
UpstreamFwd+ EgressCtrl+ DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir-
UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [950 v1] Vendor Specific Information: ID=0001 Rev=0
Len=010 <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
[root@ceds30 ~]# lspci -s 93:01.0 -vvv
93:01.0 PCI bridge: PLX Technology, Inc. PEX 8509 8-lane, 8-port PCI
Express Switch (rev aa) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=93, secondary=94, subordinate=94, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fb400000-fb4fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/2 Maskable+ 64bit+
Address: 00000000fee00398 Data: 0000
Masking: 00000002 Pending: 00000000
Capabilities: [68] Express (v1) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <2us, L1 <32us
ClockPM- Surprise+ LLActRep+ BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk-
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn+ PwrCtrl+ MRL+ AttnInd+ PwrInd+ HotPlug+ Surprise-
Slot #0, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt+ MRL+ PresDet+ CmdCplt+
HPIrq+ LinkChg-
Control: AttnInd On, PwrInd On, Power+ Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
Capabilities: [90] Subsystem: PLX Technology, Inc. PEX 8509
8-lane, 8-port PCI Express Switch
Capabilities: [dc] Vendor Specific Information: Len=14 <?>
Capabilities: [100 v1] Device Serial Number aa-85-09-10-b5-df-0e-00
Capabilities: [fb4 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [138 v1] Power Budgeting <?>
Capabilities: [148 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
Kernel modules: shpchp
# lspci -s 94:00.0 -vvv
94:00.0 USB controller: Renesas Technology Corp. uPD720202 USB 3.0
Host Controller (rev 02) (prog-if 30 [XHCI])
Physical Slot: 0-6
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 64
Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <4us, L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported,
TimeoutDis+, LTR+, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms,
TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
I am trying to found out the upd7202 firmware revison. But since the
h/w is recent, I expect the firmware to be up to date.
Any ideas on how to tackle this problem? Is there a way to really
reset the chip?
Thanks a lot,
--
_______________________________________
jean-françois simon - www.themis.com
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
