On 07.06.2015 22:20, Anand Moon wrote: > Facilitate getting required 3.3V and 1.0V VDD supply for > EHCI controller on Exynos. > > With the patches for regulators' nodes merged in 3.15: > c8c253f ARM: dts: Add regulator entries to smdk5420 > 275dcd2 ARM: dts: add max77686 pmic node for smdk5250, > the exynos systems turn on only minimal number of regulators. > > Until now, the VDD regulator supplies were either turned on > by the bootloader, or the regulators were enabled by default > in the kernel, so that the controller drivers did not need to > care about turning on these regulators on their own. > This was rather bad about these controller drivers. > So ensuring now that the controller driver requests the necessary > VDD regulators (if available, unless there are direct VDD rails), > and enable them so as to make them working. > > Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx> > Signed-off-by: Anand Moon <linux.amoon@xxxxxxxxx> > Cc: Jingoo Han <jg1.han@xxxxxxxxxxx> > Cc: Alan Stern <stern@xxxxxxxxxxxxxxxxxxx> > --- > Initial version of this patch was part of following series, though > they are not dependent on each other, resubmitting after rebasing. > > http://lists.infradead.org/pipermail/linux-arm-kernel/2014-June/266418.html So you just took Vivek's patch along with all the credits... That is not how we usually do this. I would expect that rebasing a patch won't change the author unless this is fine with Vivek. > --- > .../devicetree/bindings/usb/exynos-usb.txt | 2 + > drivers/usb/host/ehci-exynos.c | 55 +++++++++++++++++++++- > 2 files changed, 56 insertions(+), 1 deletion(-) > > diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt > index 9b4dbe3..776fa03 100644 > --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt > +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt > @@ -23,6 +23,8 @@ Required properties: > Optional properties: > - samsung,vbus-gpio: if present, specifies the GPIO that > needs to be pulled up for the bus to be powered. > + - vdd33-supply: handle to 3.3V Vdd supply regulator for the controller. > + - vdd10-supply: handle to 1.0V Vdd supply regulator for the controller. > > Example: > > diff --git a/drivers/usb/host/ehci-exynos.c b/drivers/usb/host/ehci-exynos.c > index df538fd..4f8f9d2 100644 > --- a/drivers/usb/host/ehci-exynos.c > +++ b/drivers/usb/host/ehci-exynos.c > @@ -21,6 +21,7 @@ > #include <linux/of_gpio.h> > #include <linux/phy/phy.h> > #include <linux/platform_device.h> > +#include <linux/regulator/consumer.h> > #include <linux/usb.h> > #include <linux/usb/hcd.h> > > @@ -45,6 +46,8 @@ static struct hc_driver __read_mostly exynos_ehci_hc_driver; > struct exynos_ehci_hcd { > struct clk *clk; > struct phy *phy[PHY_NUMBER]; > + struct regulator *vdd33; > + struct regulator *vdd10; > }; > > #define to_exynos_ehci(hcd) (struct exynos_ehci_hcd *)(hcd_to_ehci(hcd)->priv) > @@ -170,7 +173,27 @@ static int exynos_ehci_probe(struct platform_device *pdev) > > err = exynos_ehci_get_phy(&pdev->dev, exynos_ehci); > if (err) > - goto fail_clk; > + goto fail_regulator1; > + > + exynos_ehci->vdd33 = devm_regulator_get_optional(&pdev->dev, "vdd33"); > + if (!IS_ERR(exynos_ehci->vdd33)) { > + err = regulator_enable(exynos_ehci->vdd33); > + if (err) { > + dev_err(&pdev->dev, > + "Failed to enable 3.3V Vdd supply\n"); > + goto fail_regulator1; > + } > + } > + > + exynos_ehci->vdd10 = devm_regulator_get_optional(&pdev->dev, "vdd10"); > + if (!IS_ERR(exynos_ehci->vdd10)) { > + err = regulator_enable(exynos_ehci->vdd10); > + if (err) { > + dev_err(&pdev->dev, > + "Failed to enable 1.0V Vdd supply\n"); > + goto fail_regulator2; > + } > + } > > skip_phy: > > @@ -231,6 +254,10 @@ fail_add_hcd: > fail_io: > clk_disable_unprepare(exynos_ehci->clk); > fail_clk: > + regulator_disable(exynos_ehci->vdd10); > +fail_regulator2: > + regulator_disable(exynos_ehci->vdd33); if (!IS_ERR()). > +fail_regulator1: > usb_put_hcd(hcd); > return err; > } > @@ -246,6 +273,11 @@ static int exynos_ehci_remove(struct platform_device *pdev) > > clk_disable_unprepare(exynos_ehci->clk); > > + if (!IS_ERR(exynos_ehci->vdd33)) > + regulator_disable(exynos_ehci->vdd33); > + if (!IS_ERR(exynos_ehci->vdd10)) > + regulator_disable(exynos_ehci->vdd10); > + > usb_put_hcd(hcd); > > return 0; > @@ -268,6 +300,11 @@ static int exynos_ehci_suspend(struct device *dev) > > clk_disable_unprepare(exynos_ehci->clk); > > + if (!IS_ERR(exynos_ehci->vdd33)) > + regulator_disable(exynos_ehci->vdd33); > + if (!IS_ERR(exynos_ehci->vdd10)) > + regulator_disable(exynos_ehci->vdd10); > + Is EHCI a wakeup source? If yes then how disabling regulators during suspend affects waking up process? Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
