On 05/08/2015 10:21 PM, Alan Stern wrote:
On Fri, 8 May 2015, Lu, Baolu wrote:
On 05/07/2015 10:34 PM, Alan Stern wrote:
On Thu, 7 May 2015, Lu, Baolu wrote:
+ void (*device_suspend)(struct usb_hcd *, struct usb_device *udev,
+ pm_message_t msg);
+ void (*device_resume)(struct usb_hcd *, struct usb_device *udev,
+ pm_message_t msg);
};
Your callbacks don't use the msg argument. What makes you think it is
needed?
This msg argument is valuable. XHCI spec defines a capability named FSC
(Force Save context Capability). When this capability is implemented, the
Save State operation (do during host suspend) shall save any cached Slot,
Endpoint, Stream or other Context information to memory. xHCI hcd could
use this "msg" to determine whether it needs to issue stop endpoint with
SP (suspend) bit set.
I don't understand. What is the advantage of using FSC?
I'm sorry, I didn't make it clear.
As part of host suspend, controller save state will be issued to save
host internal state in xhci_suspend():
...
If FSC is supported, the cached Slot, Endpoint, Stream, or other
Context information are also saved.
Hence, when FSC is supported, software does not have to issue Stop
Endpoint Command to push public and private endpoint state into
memory as part of system suspend process.
Why do you have to push this state into memory at all? Does the
controller hardware lose the cached state information when it is in low
power?
I don't think controller hardware will lose the cached state information
when it is in low power. But since cache in controller consumes power
and resources, by pushing state into memory, hardware can power
off the cache logic during suspend. Hence more power saving gains.
The logic in xhci_device_suspend() will look like:
if xhci_device_suspend() callback was called due to system suspend,
(mesg.event & PM_EVENT_SUSPEND is true) and FSC is supported by
the xHC implementation, xhci_device_suspend() could ignore stop
endpoint command, since CSS will be done in xhc_suspend() later and
where all the endpoint caches will be pushed to memory.
I still don't understand this. You said earlier that according
to section 4.15.1.1 of the xHCI spec, the endpoint rings should
_always_ be stopped with SP set when a device is suspended. Now you're
The intention of stop endpoint with SP set is to tell hardware that
"a device is going to suspend, hardware don't need to contain the
endpoint state in internal cache anymore". Hardware _could_ use
this hint to push endpoint state into memory to reduce power
consumption.
saying that they don't need to be stopped during a system suspend if
the controller supports FSC. (Or maybe you're saying they need to be
stopped but SP doesn't need to be set -- it's hard to tell.)
Even FSC is supported, controller hardware still need to push cached
endpoint state into memory when a USB device is suspended. The
difference is when FSC is enforced, CSS command will push any
cached endpoint state into memory unconditionally.
So, when xhci_device_suspend() knows that CSS command will be
executed later and CSS command will push cached endpoint state
into memory (a.k.a. FSC is enforced), it could skip issuing stop
endpoint command with SP bit set to avoid duplication and reduce
the suspend time.
This is the case for system suspend since CSS command is part of
xhci_suspend() and xhci_suspend() will be executed after all USB
devices have been suspended. But it's not case for run-time suspend
(auto-pm) since USB device suspend and host controller suspend
are independent for run-time case.
That's the reason why I wanted to keep 'msg' parameter. But just as
Greg said, we don't need to keep a parameter when it's not used
and can add it later when it is required.
So which is it? Do you need to stop the endpoint rings? Is it okay
not to set SP?
"stop endpoint" and "stop endpoint with SP set" serve different purposes
in Linux xhci driver as my understanding. "stop endpoint" command is
used to stop a active ring when upper layer want to cancel a URB.
"stop endpoint with SP set" is used to hint hardware that a USB is going
to suspend. Hence "stop endpoint with SP set" must be executed in case
that the transfer ring is empty.
Alan Stern
Thank you,
Baolu
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
