Hi Johan, Am 30.03.2015 um 09:45 schrieb Johan Hovold <johan@xxxxxxxxxx>: > On Sat, Mar 28, 2015 at 02:37:57PM +0100, Marek Belisko wrote: >> From: "H. Nikolaus Schaller" <hns@xxxxxxxxxxxxx> >> >> While trying to test the Pyra GSM/GPS/3G module I had reconfigured >> the USB interface by mistake and therefore needed to run a different >> USB driver than CSC-ACM. It turned out that I need the "usbserial" driver. > > CDC-ACM oh, thanks. There is always at least one more typo in any document… > >> This file is an official description how to use it: >> Documentation/usb/usb-serial.txt >> >> But it is outdated. The parameters vendor= and product= are no longer >> available since ca. 3.12 which means that documentation is lagging behind >> quite some time. > > This is simply not true. The vendor and module parameters are still > there for usbserial (i.e. the generic driver). > > Would you mind updating this patch to document the sysfs-method as an > alternative instead? Using sysfs is preferred as that functionality can > be used with any usb-serial driver and the drivers can also be compiled > in. Hm. For me it did not work as described and therefore I searched for and found the solution cited below, which appears to confirm that it does not work any more. Only with these hints to use the /sys approach I could make it working immediately. Therefore I assumed that the documentation is outdated. But it might also be a hidden bug with the parameter passing. I had tested on 4.0-rc3. I can try a little more but it might be waste of time to find out why the old does not work, if there is a preferred method now. > >> Here was the solution: >> >> https://bbs.archlinux.org/viewtopic.php?id=175499 >> >> insmod usbserial vendor=0x#### product=0x#### >> >> becomes (first #### is vendor, second is product) >> >> modprobe usbserial >> echo #### #### >/sys/bus/usb-serial/drivers/generic/new_id >> >> This patch changes the documentation file as needed. >> >> Signed-off-by: H. Nikolaus Schaller <hns@xxxxxxxxxxxxx> >> Signed-off-by: Marek Belisko <marek@xxxxxxxxxxxxx> >> --- >> Documentation/usb/usb-serial.txt | 12 +++++++----- >> 1 file changed, 7 insertions(+), 5 deletions(-) >> >> diff --git a/Documentation/usb/usb-serial.txt b/Documentation/usb/usb-serial.txt >> index 947fa62..9f184d8 100644 >> --- a/Documentation/usb/usb-serial.txt >> +++ b/Documentation/usb/usb-serial.txt >> @@ -466,11 +466,13 @@ Generic Serial driver >> is required of your device is that it has at least one bulk in endpoint, >> or one bulk out endpoint. >> >> - To enable the generic driver to recognize your device, build the driver >> - as a module and load it by the following invocation: >> - insmod usbserial vendor=0x#### product=0x#### >> - where the #### is replaced with the hex representation of your device's >> - vendor id and product id. >> + To enable the generic driver to recognize your device, configure >> + USB_SERIAL_GENERIC=y and build the driver as a module. Then load it by the > > You don't need to build the driver as a module when using the sysfs > method. Ok, that is right and my formulation is too narrow on that. So we just s/ as a module//. > >> + following invocation: >> + modprobe usbserial >> + echo #### #### >/sys/bus/usb-serial/drivers/generic/new_id >> + where the the first #### is replaced with the hex representation of your >> + device's vendor id and the second #### by the product id. >> >> This driver has been successfully used to connect to the NetChip USB >> development board, providing a way to develop USB firmware without > > Thanks, > Johan Thanks as well, Nikolaus -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
