Hello Peter, On 15-03-19 09:19:11, Peter Chen wrote: > Hi all, > > In this patch set, I add some interfaces for tuning the performance > of chipidea usb driver. With this set, the USB performance can be improved > at some user cases with suitable parameters. The main changes: > > - Interface to tune interrupt threshold control, and set > 'Immediate' for default value > - The glue layer can disable stream mode according to USB role > - Interface to tune AHB burst configuration at SBUSCFG > - Interface to tune tx/rx burst size > - i.mx changes for achieving better performance, it can reduce > the latecy between bus and USB FIFO, and reduce the overrun > and underrun occurrences, it is useful for the system bus is busy. > we see great improvement for ISO transfer, eg, high resolution > USB camera when the bus is busy. > > Below are some test results at imx6sx sdb board > (set ehci_hcd.park=3 at bootargs), the tests are done > at v4.0 kernel, no other bus loading during the tests, > so we have not seen performance change for some use cases. > > USB Mass Storage (Host mode) > With Patch Set Without Patch Set > R: 26.9 MB/s 27 MB/s > W: 25.2 MB/s 24.5 MB/s > > 1G USB Ethernet Card > With Patch Set Without Patch Set > TX: 186 Mb/s 185 Mb/s > RX: 219 Mb/s 216 Mb/s > > g_ncm (Device Mode) > With Patch Set Without Patch Set > TX: 166MB/s 163MB/s > RX: 230MB/s 184MB/s > I tested these patches on a Colibri Vybrid VF61. Have not applied the 7th and 11th patch, but, the changes these patches introduce, I added them to our device tree node. These would be the addition of ahb-burst-config = <0x0> and tx-burst-size-dword = <0x10> and rx-burst-size-dword = <0x10> to the usb node in vfxxx.dtsi file for both the peripheral and host usb nodes. I used hdparm and dd for the tests. Some of the readings are below. With this patchset applied Reads hdparm -t --direct /dev/sda /dev/sda: Timing O_DIRECT disk reads: 36 MB in 3.05 seconds = 11.80 MB/sec Writes root@colibri-vf:~# time dd if=/dev/zero bs=128k count=4096 of=/media/sda1/tmpfile 4096+0 records in 4096+0 records out real 1m11.671s user 0m0.010s sys 0m10.130s USB Client - RNDIS root@colibri-vf:~# iperf -c 192.168.1.1 ------------------------------------------------------------ Client connecting to 192.168.1.1, TCP port 5001 TCP window size: 43.8 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.2 port 41317 connected with 192.168.1.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 105 MBytes 88.2 Mbits/sec Without this patchset applied Reads hdparm -t --direct /dev/sda /dev/sda: Timing O_DIRECT disk reads: 78 MB in 3.06 seconds = 25.50 MB/sec Writes root@colibri-vf:~# time dd if=/dev/zero bs=128k count=4096 of=/media/sda1/tmpfil 4096+0 records in 4096+0 records out real 0m43.807s user 0m0.050s sys 0m9.960s USB Client - RNDIS root@colibri-vf:~# iperf -c 192.168.1.1 ------------------------------------------------------------ Client connecting to 192.168.1.1, TCP port 5001 TCP window size: 43.8 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.2 port 49857 connected with 192.168.1.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 138 MBytes 116 Mbits/sec Perhaps I am missing something? I have the ehci_hcd.park=3 set. root@colibri-vf:~# cat /proc/cmdline ehci_hcd.park=3 ubi.mtd=ubi root=ubi0:rootfs rootfstype=ubifs ubi.fm_autoconvert=1 mtdparts=vf610_nfc:128k(vf-bcb)ro,1408k( u-boot)ro,512k(u-boot-env),-(ubi) fec_mac= consoleblank=0 console=tty1 console=ttyLP0,115200n8 mem=256M Is there any other parameter or variable I need to set? - Sanchayan > Peter Chen (12): > Doc: usb: ci-hdrc-imx: add gadget-itc-setting for binding doc > usb: chipidea: set ITC to 0 for device mode > usb: chipidea: define stream mode disable for both roles > usb: chipidea: imx: add stream mode enable for device mode at > imx6sl/imx6sx > usb: chipidea: introduce ci_platform_config > Doc: usb: ci-hdrc-imx: add ahb-burst-config for binding doc > ARM: imx6: set ahb-burst-config as 0 for USB > usb: chipidea: add ahb burst configuration > usb: chipidea: usbmisc_imx: add unburst setting for imx6 > Doc: usb: ci-hdrc-imx: add tx(rx)-burst-config-dword for binding doc > ARM: imx6: change default burst size for USB > usb: chipidea: add burst size configuration interface > > .../devicetree/bindings/usb/ci-hdrc-imx.txt | 12 +++ > arch/arm/boot/dts/imx6qdl.dtsi | 12 +++ > arch/arm/boot/dts/imx6sl.dtsi | 9 ++ > arch/arm/boot/dts/imx6sx.dtsi | 9 ++ > drivers/usb/chipidea/bits.h | 7 ++ > drivers/usb/chipidea/ci.h | 3 + > drivers/usb/chipidea/ci_hdrc_imx.c | 14 ++- > drivers/usb/chipidea/core.c | 119 +++++++++++++++++++-- > drivers/usb/chipidea/host.c | 6 +- > drivers/usb/chipidea/usbmisc_imx.c | 12 ++- > include/linux/usb/chipidea.h | 11 +- > 11 files changed, 191 insertions(+), 23 deletions(-) > > -- > 1.9.1 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
