Hi Robert, Did you test the extcon-odroid-otg driver on Odroid-U3? Thanks, Chanwoo Choi On 03/18/2015 11:04 PM, Robert Baldyga wrote: > Hello, > > This patchset introduces OTG feature in DWC3 DRD driver. This allows > to change dynamically between host and peripheral mode depending on > detected USB cable type. > > DWC3 driver behaviour is changed only in situation when selected operation > mode (dr_mode) is "otg", and hardware OTG support is available or extended > OTG operations are supplied for given platform. > > It such conditions are fulfilled, none of modes is enabled by default > and dwc3 core Best regards, > Robert Baldygais being uninitialized. After USB cable detection relevant > mode is selected and dwc3 core is initialized. Cable disconnection causes > deinitialization of dwc3 core. > > File otg.c is inspired by code of DWC3 driver from Hardkernel linux > sources [1]. I have never tested it on DWC3 version equipped with hardware > OTG support, but I belive that this code have chance to work or at least > it's easy to fix. I have tested this on OdroidXU3 board which has USB > cable detection mechanism based on two gpio pins. I used extcon driver > for those feature, which is also attached to following patchset. > > I consider if ext_otg_ops it the right solution. Current solution is > based on Hardkernel sources, but it's very likely that adding extcon > support directly to otg.c would be generic enough, as most of cable > detection mechanisms can be simply represented by extcon devices. > > Thanks in advance for your comments. > > Best regards, > Robert Baldyga > > [1] https://github.com/hardkernel/linux > > Robert Baldyga (19): > extcon: add extcon-odroid-usbotg driver > dt-bindings: extcon: Add doc for extcon-odroid-usbotg > ARM: dts: exynos5422-odroidxu3: add odroid-usbotg extcon support > dwc3: gadget: add VBUS session handling > dwc3: gadget: enable/disable ep0 in dwc3_gadget_run_stop() > dwc3: gadget: check returned value in suspend/resume > dwc3: core: cleanup suspend/resume code > dwc3: core: handle event buffers in core_init/exit > dwc3: core: make dwc3_core_init/exit non-static > dwc3: add missing OTG register definitions > dwc3: add OTG handling code > dwc3: otg: add ext_otg_ops support > dwc3: gadget: register gadget in OTG core > dwc3: host: don't add XHCI device only if in OTG mode > dwc3: core: initialize OTG in DWC3 core > dwc3: exynos: add software role switching code > ARM: dts: exynos5420: set usb3_lpm_capable in dwc3 controllers > ARM: dts: exynos5420: add snps,dis_u3_susphy_quirk to dwc3 controllers > ARM: dts: exynos5422-odroidxu3: make usbdrd3 extcon client > > .../bindings/extcon/extcon-odroid-usbotg.txt | 16 + > .../devicetree/bindings/usb/exynos-usb.txt | 4 + > arch/arm/boot/dts/exynos5420.dtsi | 6 + > arch/arm/boot/dts/exynos5422-odroidxu3.dts | 24 + > drivers/extcon/Kconfig | 4 + > drivers/extcon/Makefile | 1 + > drivers/extcon/extcon-odroid-usbotg.c | 257 +++++++++ > drivers/usb/dwc3/Kconfig | 1 + > drivers/usb/dwc3/Makefile | 4 + > drivers/usb/dwc3/core.c | 66 ++- > drivers/usb/dwc3/core.h | 22 + > drivers/usb/dwc3/dwc3-exynos.c | 162 ++++++ > drivers/usb/dwc3/gadget.c | 106 ++-- > drivers/usb/dwc3/host.c | 10 +- > drivers/usb/dwc3/otg.c | 577 +++++++++++++++++++++ > drivers/usb/dwc3/otg.h | 113 ++++ > 16 files changed, 1320 insertions(+), 53 deletions(-) > create mode 100644 Documentation/devicetree/bindings/extcon/extcon-odroid-usbotg.txt > create mode 100644 drivers/extcon/extcon-odroid-usbotg.c > create mode 100644 drivers/usb/dwc3/otg.c > create mode 100644 drivers/usb/dwc3/otg.h > -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
