Re: [PATCHv3 2/2] USB: gadget: atmel_usba_udc: Enable/disable USB PLL on Vbus change

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, 19 Jan 2015 18:46:31 +0100
Sylvain Rochet <sylvain.rochet@xxxxxxxxxxxx> wrote:

> Hello Nicolas,
> 
> 
> On Mon, Jan 19, 2015 at 05:55:18PM +0100, Nicolas Ferre wrote:
> > Le 18/01/2015 18:24, Sylvain Rochet a écrit :
> > > Prepare_enable on rising edge, disable_unprepare on falling edge. Reduce
> >
> > Please re-write which "edge" we are talking about: "... falling edge of
> > the Vbus signal" for example.
> >
> > > power consumption if USB PLL is not already necessary for OHCI or EHCI.
> >
> > Is a verb missing in the previous sentence?
> >
> > > If USB host is not connected we can sleep with USB PLL stopped.
> > >
> > > This driver does not support suspend/resume yet, not suspending if we
> > > are still attached to an USB host is fine for what I need, this patch
> > > allow suspending with USB PLL stopped when USB device is not currently
> > > used.
> >
> > Can you please make it more clear. Several separated sentences seem
> > necessary here.
> 
> Maybe :)
> 
> 
> Proposal:
> 
> Start clocks on rising edge of the Vbus signal, stop clocks on 
> falling edge of the Vbus signal.
> 
> If USB PLL is not necessary for other USB drivers (e.g. OHCI and EHCI) 
> it will reduce power consumption by switching off the USB PLL if no USB 
> Host is currently connected to this USB Device.
> 
> We are using Vbus GPIO signal to detect Host presence. If Vbus signal is 
> not available then the device stay continuously clocked.
> 
> Note this driver does not support suspend/resume yet, it may stay 
> clocked if USB Host is still connected when suspending. For what I need, 
> forbidding suspend from userland if we are still attached to an USB host 
> is fine, but we might as well add suspend/resume to this driver in the 
> future.
> 
> 
> 
> > >  	/* May happen if Vbus pin toggles during probe() */
> > > -	if (!udc->driver)
> > > +	spin_lock_irqsave(&udc->lock, flags);
> > > +	if (!udc->driver) {
> > > +		spin_unlock_irqrestore(&udc->lock, flags);
> > >  		goto out;
> > > +	}
> > > +	spin_unlock_irqrestore(&udc->lock, flags);
> > 
> > I'm not sure that the protection by spin_lock is needed above.
> 
> I'm not sure too, it was already in a spinlock area, I obviously kept it 
> because it was not the purpose of this patch.

According to the comment placed above this test it's here to prevent
any action triggered by the vbus pin irq while the driver is not
properly probed yet.
You could use:

set_irq_flags(vbus_irq, IRQF_NOAUTOEN);

before calling devm_request_threaded_irq.
This will keep the irq disabled instead of enabling it at request time.
Moreover, this simplify the vbus_irq request code (which disables the
irq just after requesting it).

> 
> This seem to be in mirror of atmel_usba_start() which does:
> 
>   spin_lock_irqsave(&udc->lock, flags);
>   udc->devstatus = 1 << USB_DEVICE_SELF_POWERED;
>   udc->driver = driver;
>   spin_unlock_irqrestore(&udc->lock, flags);
> 
> … but vbus_pin IRQ is not yet enabled.
> 
> 
> Same for atmel_usba_stop() which disable vbus_pin IRQ before setting 
> udc->driver to NULL, but without spinlock this time (why?, this should 
> be consistent IMHO).
> 
> 
> I don't know if it is guaranteed that IRQ does not fire nor continue to 
> run after disable_irq() returns, especially for threaded IRQ.

And yes, disable_irq waits for all irq handler termination, including
threaded irqs: see [1], [2]. 

> 
> 
> If the following sequence might happen:
>   atmel_usba_stop()
>     disable_irq(vbus)
>                                   usba_vbus_irq_thread() called lately
>                                     check for (!udc->driver) and continue
>     udc->driver = NULL;
>                                     if (udc->driver->disconnect)
>                                  *CRASH*
> 
> Then the patch should be modified to protect udc->driver with the vbus 
> mutex.
> 
> In this case the previous implementation wasn't perfect too, the 
> atmel_usba_stop() does not lock around the NULLification of driver, 
> 
> Moreover the spinlock is (and was) unlocked in VBUS interrupt just 
> before calling udc->driver->disconnect, which makes udc->driver actually 
> not locked anywere.
> 
> If the previous sequence possible ?  If no, udc->driver does not need 
> locking, if yes, it is currently not locked enough.

If you rework the vbus_irq request as I suggested I think you can get
rid of this !udc->driver test, and thus drop the locking around it ;-).

Best Regards,

Boris

[1]http://lxr.free-electrons.com/source/kernel/irq/manage.c#L432
[2]http://lxr.free-electrons.com/source/kernel/irq/manage.c#L92



-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux