On Fri, Dec 05, 2014 at 01:51:17PM +0200, Octavian Purdila wrote:
> On Fri, Dec 5, 2014 at 12:17 PM, Johan Hovold <johan@xxxxxxxxxx> wrote:
> > On Thu, Nov 27, 2014 at 01:57:14PM +0200, Octavian Purdila wrote:
> >
> >> @@ -753,11 +759,42 @@ static const struct usb_device_id dln2_table[] = {
> >>
> >> MODULE_DEVICE_TABLE(usb, dln2_table);
> >
> > Place the new callbacks above the device id table.
> >
> >> +static int dln2_suspend(struct usb_interface *iface, pm_message_t message)
> >> +{
> >> + struct dln2_dev *dln2 = usb_get_intfdata(iface);
> >> +
> >> + dln2_stop(dln2);
> >
> > You should also stop the reads urbs here.
>
> Do you mean usb_kill_urb()? I thought that was not necessary unless
> the device is reset. However, going throught
> Documentation/usb/power-management.txt again looks like it must be
> done in suspend.
Yes, you should kill them explicitly. Any outstanding urbs will be
killed by usb core if you fail to do this.
> >> + return 0;
> >> +}
> >> +
> >> +static int dln2_resume(struct usb_interface *iface)
> >> +{
> >> + struct dln2_dev *dln2 = usb_get_intfdata(iface);
> >> +
> >> + dln2->disconnect = false;
> >
> > And surely you need to resubmit the read urbs in resume, or you will
> > never receive any more data.
> >
> > How did you test this patch?
> >
>
> The resume cb is not called in my setup (kvm), only reset_resume.
Please make sure to test your patches on proper hardware.
> But I assume since the port is not reset when resume is called the
> URBs are still queued.
No, they will have been killed by usb core even if you forget to do it,
so this would prevent any further reads.
> >> + return 0;
> >> +}
> >> +
> >> +static int dln2_reset_resume(struct usb_interface *iface)
> >> +{
> >> + struct dln2_dev *dln2 = usb_get_intfdata(iface);
> >> + int ret;
> >> +
> >> + dln2_free_rx_urbs(dln2);
> >> + ret = dln2_setup_rx_urbs(dln2, iface->cur_altsetting);
> >
> > This doesn't make much sense. Why would you ever want to reallocate the
> > urbs and their buffers here?
> >
> > If the device does not lose its state as you claim, then all you need to
> > do is to resubmit the read urbs (as in resume).
> >
> The device itself does not lose state as it does not lose power and
> does not react to USB port reset AFAICS (e.g. GPIO settings are
> preserved). However the USB port is reset and I assumed I must
> reallocate the URBs.
You don't and should not.
> I just found out that usb-serial uses usb_poisoin_urb and
> usb_unpoison_urb for suspend/resume and this two looks like just what
> I need.
Why do you think so?
> Should I use that instead?
No.
Johan
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
