Hi, On 08/15/2014 09:44 AM, Claudio Bizzarri wrote: >> On Thu, Aug 14, 2014 at 11:46:33AM +0200, Hans de Goede wrote: >>> Hi, > ... >>> >>> Can you collect "lsusb -v" output for the drive in question when connected >>> through an usb-3 port (the uas module does not need to be loaded). > > Here lsusb output, full text as attachment Thanks. > Bus 003 Device 003: ID 152d:0567 JMicron Technology Corp. / JMicron > USA Technology Corp. > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 3.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 9 > idVendor 0x152d JMicron Technology Corp. / JMicron USA > Technology Corp. > idProduct 0x0567 > bcdDevice 0.00 > iManufacturer 10 JMicron > iProduct 11 USB to ATA/ATAPI Bridge > iSerial 5 152D00539000 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 121 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xc0 > Self Powered > MaxPower 2mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 2 > bInterfaceClass 8 Mass Storage > bInterfaceSubClass 6 SCSI > bInterfaceProtocol 80 Bulk-Only > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0400 1x 1024 bytes > bInterval 0 > bMaxBurst 15 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x02 EP 2 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0400 1x 1024 bytes > bInterval 0 > bMaxBurst 15 > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 1 > bNumEndpoints 4 > bInterfaceClass 8 Mass Storage > bInterfaceSubClass 6 SCSI > bInterfaceProtocol 98 > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x01 EP 1 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0400 1x 1024 bytes > bInterval 0 > bMaxBurst 0 > Command pipe (0x01) > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x82 EP 2 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0400 1x 1024 bytes > bInterval 0 > bMaxBurst 0 > MaxStreams 32 32, ok that is the amount which we know jmicron chips can handle over usb-2, so one would expect that having 32 outstanding commands will work when connected over usb-3 too. > Status pipe (0x02) > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0400 1x 1024 bytes > bInterval 0 > bMaxBurst 15 > MaxStreams 32 > Data-in pipe (0x03) > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x04 EP 4 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0400 1x 1024 bytes > bInterval 0 > bMaxBurst 15 > MaxStreams 32 > Data-out pipe (0x04) > Binary Object Store Descriptor: > bLength 5 > bDescriptorType 15 > wTotalLength 22 > bNumDeviceCaps 2 > USB 2.0 Extension Device Capability: > bLength 7 > bDescriptorType 16 > bDevCapabilityType 2 > bmAttributes 0x00000002 > Link Power Management (LPM) Supported > SuperSpeed USB Device Capability: > bLength 10 > bDescriptorType 16 > bDevCapabilityType 3 > bmAttributes 0x00 > wSpeedsSupported 0x000e > Device can operate at Full Speed (12Mbps) > Device can operate at High Speed (480Mbps) > Device can operate at SuperSpeed (5Gbps) > bFunctionalitySupport 1 > Lowest fully-functional device speed is Full Speed (12Mbps) > bU1DevExitLat 10 micro seconds > bU2DevExitLat 2047 micro seconds > Device Status: 0x0001 > Self Powered > >>> Also can you try the following patch, and see if that makes uas work ? : >>> >>> diff --git a/drivers/usb/storage/uas.c b/drivers/usb/storage/uas.c >>> index 511b229..6cdc1b9 100644 >>> --- a/drivers/usb/storage/uas.c >>> +++ b/drivers/usb/storage/uas.c >>> @@ -1033,6 +1033,7 @@ static int uas_configure_endpoints(struct uas_dev_info *devinfo) >>> 3, 256, GFP_NOIO); >>> if (devinfo->qdepth < 0) >>> return devinfo->qdepth; >>> + devinfo->qdepth = 32; >>> devinfo->use_streams = 1; >>> } > > I believe that recompile uas.ko module is a too hard task for me: some > years ago I usually recompile kernel on RedHat distribution, but there > was a srpm package and a simple rpm --rebuild command solved. Now I'm > using a Ubuntu distribution and I believe that recompile a ppa version > of kernel is a "bit" hard. > > If I found a simple way to obtain a uas.ka module I'll try your patch. There is no need to try my patch, since the descriptors already limit qdepth to 32. No idea what is going on here then. Regards, Hans -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
