Hi,
On Tue, Jul 22, 2014 at 10:18:00AM +0100, Peter Griffin wrote:
> > > +static inline u32 st_dwc3_readl(void __iomem *base, u32 offset)
> > > +{
> > > + return readl_relaxed(base + offset);
> > > +}
> > > +
> > > +static inline void st_dwc3_writel(void __iomem *base, u32 offset, u32 value)
> > > +{
> > > + writel_relaxed(value, base + offset);
> > > +}
> >
> > Why are these being abstracted?
> >
> > Just use {read,write}l_relaxed() directly.
>
> Ok, unabstracted in v3
no, no... all other glues add their own local helpers for register
access. This is good for tracing, it's very easy to add a tracepoint to
this sort of function and get very low overhead tracing of every
register access.
> > > + if (dwc3_data->drd_device_conf)
> > > + val |= USB_SET_PORT_DEVICE;
> > > + else
> > > + val &= USB_HOST_DEFAULT_MASK;
> > > +
> > > + return regmap_write(dwc3_data->regmap, dwc3_data->syscfg_reg_off, val);
> > > +}
> > > +
> > > +/**
> > > + * st_dwc3_init: init the controller via glue logic
> > > + * @dwc3_data: driver private structure
> > > + */
> > > +static void st_dwc3_init(struct st_dwc3 *dwc3_data)
> > > +{
> > > + u32 reg = st_dwc3_readl(dwc3_data->glue_base, USB2_CLKRST_CTRL);
> > > +
> > > + reg |= aux_clk_en(1) | ext_cfg_reset_n(1) | xhci_revision(1);
> > > + reg &= ~sw_pipew_reset_n(1);
> >
> > 1? Better to add defines for these magic numbers. What is 1 anyway?
>
> They are just bit setting macros, I've converted them over to use BIT macro now,
> so it no longer takes a parameter.
the macros are better, but make them upper case as everybody else.
> > > + st_dwc3_writel(dwc3_data->glue_base, USB2_CLKRST_CTRL, reg);
> > > +
> > > + reg = st_dwc3_readl(dwc3_data->glue_base, USB2_VBUS_MNGMNT_SEL1);
> > > + reg |= SEL_OVERRIDE_VBUSVALID(1) | SEL_OVERRIDE_POWERPRESENT(1) |
> > > + SEL_OVERRIDE_BVALID(1);
> > > + st_dwc3_writel(dwc3_data->glue_base, USB2_VBUS_MNGMNT_SEL1, reg);
> > > + udelay(100);
> >
> > Why 100?
>
> I've asked ST how this value was derirved and why. It came from validation.
> The docs don't mention that it is necessary, and removing it
> seems to have no ill effects. So I've removed this udelay in v3.
make sure to test with many, many iterations just to make sure.
> > > + reg = st_dwc3_readl(dwc3_data->glue_base, USB2_CLKRST_CTRL);
> > > + reg |= sw_pipew_reset_n(1);
> > > + st_dwc3_writel(dwc3_data->glue_base, USB2_CLKRST_CTRL, reg);
> > > +}
> > > +
> > > +static void st_dwc3_dt_get_pdata(struct platform_device *pdev,
> > > + struct st_dwc3 *dwc3_data)
> > > +{
> > > + struct device_node *np = pdev->dev.of_node;
> > > +
> > > + dwc3_data->drd_device_conf =
> > > + of_property_read_bool(np, "st,dwc3-drd-device");
> >
> > This requires a DT Ack.
>
> Ok. Do the DT folks have any comment on this?
look at the child's dr-mode property instead of adding your own.
> > > + dwc3_data->glue_base = devm_request_and_ioremap(dev, res);
use devm_ioremap_resource()
> > > + regmap = syscon_regmap_lookup_by_phandle(node, "st,syscfg");
> > > + if (IS_ERR(regmap))
> > > + return PTR_ERR(regmap);
> > > +
> > > + dwc3 = platform_device_alloc("st-dwc3", PLATFORM_DEVID_AUTO);
> > > + if (!dwc3) {
> > > + dev_err(&pdev->dev, "couldn't allocate dwc3 device\n");
> > > + return -ENOMEM;
> > > + }
> >
> > I'm confused. What is this doing? Isn't this the DWC3 driver, which
> > already had a platform device structure associated to it? Perhaps a
> > small ASCII diagram describing the layers might be useful.
>
> Your right, this was wrong. It was some legacy code which is
> unnecessary and I've removed this in v3.
if you're going for DT, why don't you create the parent and the child
from DT as omap/exynos/qcom are doing ?
> > > + dma_set_coherent_mask(&dwc3->dev, dev->coherent_dma_mask);
> > > +
> > > + dwc3->dev.parent = &pdev->dev;
> > > + dwc3->dev.dma_mask = pdev->dev.dma_mask;
> > > + dwc3->dev.dma_parms = pdev->dev.dma_parms;
stick to DT device creation. Look into dwc3-omap.c
> > > +static int st_dwc3_remove(struct platform_device *pdev)
> > > +{
> > > + struct st_dwc3 *dwc3_data = platform_get_drvdata(pdev);
> > > +
> > > + platform_device_unregister(dwc3_data->dwc3);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +#ifdef CONFIG_PM_SLEEP
> > > +static int st_dwc3_suspend(struct device *dev)
> > > +{
> > > + struct st_dwc3 *dwc3_data = dev_get_drvdata(dev);
> > > +
> > > + reset_control_assert(dwc3_data->rstc_pwrdn);
> > > +
> > > + pinctrl_pm_select_sleep_state(dev);
pinctrl will select sleep and default states automatically for you.
--
balbi
Attachment:
signature.asc
Description: Digital signature
