Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.
Thereby, removing old phy-samsung-usb3 driver and related code
used untill now which was based on usb/phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
---
Changes from v6:
- Addressed review comments:
-- Sorted config entries in Kconfig and Makefile
-- Made #define to_usbdrd_phy(inst) to a static inline routine.
-- Restructured exynos5_rate_to_clk() as suggested.
-- Amended 'val' field for regmap_update_bits() in the routine
exynos5_usbdrd_phy_isol().
-- Removed sentinel entry from exynos5_usbdrd_phy_cfg[] struct.
-- Removed check for 'match' entry in probe().
.../devicetree/bindings/phy/samsung-phy.txt | 40 ++
drivers/phy/Kconfig | 11 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-exynos5-usbdrd.c | 627 ++++++++++++++++++++
4 files changed, 679 insertions(+)
create mode 100644 drivers/phy/phy-exynos5-usbdrd.c
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index b422e38..51efe4c 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -114,3 +114,43 @@ Example:
compatible = "samsung,exynos-sataphy-i2c";
reg = <0x38>;
};
+
+Samsung Exynos5 SoC series USB DRD PHY controller
+--------------------------------------------------
+
+Required properties:
+- compatible : Should be set to one of the following supported values:
+ - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC,
+ - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC.
+- reg : Register offset and length of USB DRD PHY register set;
+- clocks: Clock IDs array as required by the controller
+- clock-names: names of clocks correseponding to IDs in the clock property;
+ Required clocks:
+ - phy: main PHY clock (same as USB DRD controller i.e. DWC3 IP clock),
+ used for register access.
+ - ref: PHY's reference clock (usually crystal clock), used for
+ PHY operations, associated by phy name. It is used to
+ determine bit values for clock settings register.
+ For Exynos5420 this is given as 'sclk_usbphy30' in CMU.
+- samsung,pmu-syscon: phandle for PMU system controller interface, used to
+ control pmu registers for power isolation.
+- samsung,pmu-offset: phy power control register offset to pmu-system-controller
+ base.
+- #phy-cells : from the generic PHY bindings, must be 1;
+
+For "samsung,exynos5250-usbdrd-phy" and "samsung,exynos5420-usbdrd-phy"
+compatible PHYs, the second cell in the PHY specifier identifies the
+PHY id, which is interpreted as follows:
+ 0 - UTMI+ type phy,
+ 1 - PIPE3 type phy,
+
+Example:
+ usb3_phy: usbphy@12100000 {
+ compatible = "samsung,exynos5250-usbdrd-phy";
+ reg = <0x12100000 0x100>;
+ clocks = <&clock 286>, <&clock 1>;
+ clock-names = "phy", "ref";
+ samsung,pmu-syscon = <&pmu_system_controller>;
+ samsung,pmu-offset = <0x704>;
+ #phy-cells = <1>;
+ };
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 3bb05f1..daa1707 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -159,6 +159,17 @@ config PHY_EXYNOS5250_USB2
particular SoC is compiled in the driver. In case of Exynos 5250 four
phys are available - device, host, HSIC0 and HSIC.
+config PHY_EXYNOS5_USBDRD
+ tristate "Exynos5 SoC series USB DRD PHY driver"
+ depends on ARCH_EXYNOS5 && OF
+ depends on HAS_IOMEM
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Enable USB DRD PHY support for Exynos 5 SoC series.
+ This driver provides PHY interface for USB 3.0 DRD controller
+ present on Exynos5 SoC series.
+
config PHY_XGENE
tristate "APM X-Gene 15Gbps PHY support"
depends on HAS_IOMEM && OF && (ARM64 || COMPILE_TEST)
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 2faf78e..333ba98 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -17,4 +17,5 @@ obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-samsung-usb2.o
obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o
obj-$(CONFIG_PHY_EXYNOS4X12_USB2) += phy-exynos4x12-usb2.o
obj-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o
+obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
diff --git a/drivers/phy/phy-exynos5-usbdrd.c b/drivers/phy/phy-exynos5-usbdrd.c
new file mode 100644
index 0000000..bc381e3
--- /dev/null
+++ b/drivers/phy/phy-exynos5-usbdrd.c
@@ -0,0 +1,627 @@
+/*
+ * Samsung EXYNOS5 SoC series USB DRD PHY driver
+ *
+ * Phy provider for USB 3.0 DRD controller on Exynos5 SoC series
+ *
+ * Copyright (C) 2014 Samsung Electronics Co., Ltd.
+ * Author: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+/* Exynos USB PHY registers */
+#define EXYNOS5_FSEL_9MHZ6 0x0
+#define EXYNOS5_FSEL_10MHZ 0x1
+#define EXYNOS5_FSEL_12MHZ 0x2
+#define EXYNOS5_FSEL_19MHZ2 0x3
+#define EXYNOS5_FSEL_20MHZ 0x4
+#define EXYNOS5_FSEL_24MHZ 0x5
+#define EXYNOS5_FSEL_50MHZ 0x7
+
+/* EXYNOS5: USB 3.0 DRD PHY registers */
+#define EXYNOS5_DRD_LINKSYSTEM 0x04
+
+#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
+#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
+#define LINKSYSTEM_XHCI_VERSION_CONTROL BIT(27)
+
+#define EXYNOS5_DRD_PHYUTMI 0x08
+
+#define PHYUTMI_OTGDISABLE BIT(6)
+#define PHYUTMI_FORCESUSPEND BIT(1)
+#define PHYUTMI_FORCESLEEP BIT(0)
+
+#define EXYNOS5_DRD_PHYPIPE 0x0c
+
+#define EXYNOS5_DRD_PHYCLKRST 0x10
+
+#define PHYCLKRST_EN_UTMISUSPEND BIT(31)
+
+#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
+#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
+
+#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
+#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
+
+#define PHYCLKRST_SSC_EN BIT(20)
+#define PHYCLKRST_REF_SSP_EN BIT(19)
+#define PHYCLKRST_REF_CLKDIV2 BIT(18)
+
+#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
+
+#define PHYCLKRST_FSEL_UTMI_MASK (0x7 << 5)
+#define PHYCLKRST_FSEL_PIPE_MASK (0x7 << 8)
+#define PHYCLKRST_FSEL(_x) ((_x) << 5)
+#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
+#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
+#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
+#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
+
+#define PHYCLKRST_RETENABLEN BIT(4)
+
+#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
+#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
+#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
+
+#define PHYCLKRST_PORTRESET BIT(1)
+#define PHYCLKRST_COMMONONN BIT(0)
+
+#define EXYNOS5_DRD_PHYREG0 0x14
+#define EXYNOS5_DRD_PHYREG1 0x18
+
+#define EXYNOS5_DRD_PHYPARAM0 0x1c
+
+#define PHYPARAM0_REF_USE_PAD BIT(31)
+#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
+#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
+
+#define EXYNOS5_DRD_PHYPARAM1 0x20
+
+#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
+#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
+
+#define EXYNOS5_DRD_PHYTERM 0x24
+
+#define EXYNOS5_DRD_PHYTEST 0x28
+
+#define PHYTEST_POWERDOWN_SSP BIT(3)
+#define PHYTEST_POWERDOWN_HSP BIT(2)
+
+#define EXYNOS5_DRD_PHYADP 0x2c
+
+#define EXYNOS5_DRD_PHYUTMICLKSEL 0x30
+
+#define PHYUTMICLKSEL_UTMI_CLKSEL BIT(2)
+
+#define EXYNOS5_DRD_PHYRESUME 0x34
+#define EXYNOS5_DRD_LINKPORT 0x44
+
+/* Power isolation defined in power management unit */
+#define EXYNOS5_USBDRD_PMU_ISOL BIT(0)
+
+#define KHZ 1000
+#define MHZ (KHZ * KHZ)
+
+enum exynos5_usbdrd_phy_id {
+ EXYNOS5_DRDPHY_UTMI,
+ EXYNOS5_DRDPHY_PIPE3,
+ EXYNOS5_DRDPHYS_NUM,
+};
+
+struct phy_usb_instance;
+struct exynos5_usbdrd_phy;
+
+struct usbdrd_phy_config {
+ u32 id;
+ void (*phy_isol)(struct phy_usb_instance *inst, u32 on);
+ void (*phy_init)(struct exynos5_usbdrd_phy *phy_drd);
+ unsigned int (*set_refclk)(struct phy_usb_instance *inst);
+};
+
+struct exynos5_usbdrd_phy_drvdata {
+ const struct usbdrd_phy_config *phy_cfg;
+};
+
+/**
+ * struct exynos5_usbdrd_phy - driver data for USB 3.0 PHY
+ * @dev: pointer to device instance of this platform device
+ * @reg_phy: usb phy controller register memory base
+ * @clk: phy clock for register access
+ * @drv_data: pointer to SoC level driver data structure
+ * @phys[]: array for 'EXYNOS5_DRDPHYS_NUM' number of PHY
+ * instances each with its 'phy' and 'phy_cfg'.
+ * @extrefclk: frequency select settings when using 'separate
+ * reference clocks' for SS and HS operations
+ * @ref_clk: reference clock to PHY block from which PHY's
+ * operational clocks are derived
+ * @ref_rate: rate of above reference clock
+ */
+struct exynos5_usbdrd_phy {
+ struct device *dev;
+ void __iomem *reg_phy;
+ struct clk *clk;
+ const struct exynos5_usbdrd_phy_drvdata *drv_data;
+ struct phy_usb_instance {
+ struct phy *phy;
+ u32 index;
+ struct regmap *reg_pmu;
+ u32 pmu_offset;
+ const struct usbdrd_phy_config *phy_cfg;
+ } phys[EXYNOS5_DRDPHYS_NUM];
+ u32 extrefclk;
+ struct clk *ref_clk;
+};
+
+static inline
+struct exynos5_usbdrd_phy *to_usbdrd_phy(struct phy_usb_instance *inst)
+{
+ return container_of((inst), struct exynos5_usbdrd_phy,
+ phys[(inst)->index]);
+}
+
+/*
+ * exynos5_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static unsigned int exynos5_rate_to_clk(unsigned long rate, u32 *reg)
+{
+ /* EXYNOS5_FSEL_MASK */
+
+ switch (rate) {
+ case 9600 * KHZ:
+ *reg = EXYNOS5_FSEL_9MHZ6;
+ break;
+ case 10 * MHZ:
+ *reg = EXYNOS5_FSEL_10MHZ;
+ break;
+ case 12 * MHZ:
+ *reg = EXYNOS5_FSEL_12MHZ;
+ break;
+ case 19200 * KHZ:
+ *reg = EXYNOS5_FSEL_19MHZ2;
+ break;
+ case 20 * MHZ:
+ *reg = EXYNOS5_FSEL_20MHZ;
+ break;
+ case 24 * MHZ:
+ *reg = EXYNOS5_FSEL_24MHZ;
+ break;
+ case 50 * MHZ:
+ *reg = EXYNOS5_FSEL_50MHZ;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void exynos5_usbdrd_phy_isol(struct phy_usb_instance *inst,
+ unsigned int on)
+{
+ unsigned int val;
+
+ if (!inst->reg_pmu)
+ return;
+
+ val = on ? 0 : EXYNOS5_USBDRD_PMU_ISOL;
+
+ regmap_update_bits(inst->reg_pmu, inst->pmu_offset,
+ EXYNOS5_USBDRD_PMU_ISOL, val);
+}
+
+/*
+ * Sets the pipe3 phy's clk as EXTREFCLK (XXTI) which is internal clock
+ * from clock core. Further sets multiplier values and spread spectrum
+ * clock settings for SuperSpeed operations.
+ */
+static unsigned int
+exynos5_usbdrd_pipe3_set_refclk(struct phy_usb_instance *inst)
+{
+ static u32 reg;
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+ /* restore any previous reference clock settings */
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ /* Use EXTREFCLK as ref clock */
+ reg &= ~PHYCLKRST_REFCLKSEL_MASK;
+ reg |= PHYCLKRST_REFCLKSEL_EXT_REFCLK;
+
+ /* FSEL settings corresponding to reference clock */
+ reg &= ~PHYCLKRST_FSEL_PIPE_MASK |
+ PHYCLKRST_MPLL_MULTIPLIER_MASK |
+ PHYCLKRST_SSC_REFCLKSEL_MASK;
+ switch (phy_drd->extrefclk) {
+ case EXYNOS5_FSEL_50MHZ:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x00));
+ break;
+ case EXYNOS5_FSEL_24MHZ:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x88));
+ break;
+ case EXYNOS5_FSEL_20MHZ:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x00));
+ break;
+ case EXYNOS5_FSEL_19MHZ2:
+ reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
+ PHYCLKRST_SSC_REFCLKSEL(0x88));
+ break;
+ default:
+ dev_dbg(phy_drd->dev, "unsupported ref clk\n");
+ break;
+ }
+
+ return reg;
+}
+
+/*
+ * Sets the utmi phy's clk as EXTREFCLK (XXTI) which is internal clock
+ * from clock core. Further sets the FSEL values for HighSpeed operations.
+ */
+static unsigned int
+exynos5_usbdrd_utmi_set_refclk(struct phy_usb_instance *inst)
+{
+ static u32 reg;
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+ /* restore any previous reference clock settings */
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ reg &= ~PHYCLKRST_REFCLKSEL_MASK;
+ reg |= PHYCLKRST_REFCLKSEL_EXT_REFCLK;
+
+ reg &= ~PHYCLKRST_FSEL_UTMI_MASK |
+ PHYCLKRST_MPLL_MULTIPLIER_MASK |
+ PHYCLKRST_SSC_REFCLKSEL_MASK;
+ reg |= PHYCLKRST_FSEL(phy_drd->extrefclk);
+
+ return reg;
+}
+
+static void exynos5_usbdrd_pipe3_init(struct exynos5_usbdrd_phy *phy_drd)
+{
+ u32 reg;
+
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+ /* Set Tx De-Emphasis level */
+ reg &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
+ reg |= PHYPARAM1_PCS_TXDEEMPH;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+ reg &= ~PHYTEST_POWERDOWN_SSP;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+}
+
+static void exynos5_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
+{
+ u32 reg;
+
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+ /* Set Loss-of-Signal Detector sensitivity */
+ reg &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
+ reg |= PHYPARAM0_REF_LOSLEVEL;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+ /* Set Tx De-Emphasis level */
+ reg &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
+ reg |= PHYPARAM1_PCS_TXDEEMPH;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+
+ /* UTMI Power Control */
+ writel(PHYUTMI_OTGDISABLE, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMI);
+
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+ reg &= ~PHYTEST_POWERDOWN_HSP;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+}
+
+static int exynos5_usbdrd_phy_init(struct phy *phy)
+{
+ int ret;
+ u32 reg;
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+ ret = clk_prepare_enable(phy_drd->clk);
+ if (ret)
+ return ret;
+
+ /* Reset USB 3.0 PHY */
+ writel(0x0, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+ writel(0x0, phy_drd->reg_phy + EXYNOS5_DRD_PHYRESUME);
+
+ /*
+ * Setting the Frame length Adj value[6:1] to default 0x20
+ * See xHCI 1.0 spec, 5.2.4
+ */
+ reg = LINKSYSTEM_XHCI_VERSION_CONTROL |
+ LINKSYSTEM_FLADJ(0x20);
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
+
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+ /* Select PHY CLK source */
+ reg &= ~PHYPARAM0_REF_USE_PAD;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+
+ /* This bit must be set for both HS and SS operations */
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMICLKSEL);
+ reg |= PHYUTMICLKSEL_UTMI_CLKSEL;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMICLKSEL);
+
+ /* UTMI or PIPE3 specific init */
+ inst->phy_cfg->phy_init(phy_drd);
+
+ /* reference clock settings */
+ reg = inst->phy_cfg->set_refclk(inst);
+
+ /* Digital power supply in normal operating mode */
+ reg |= PHYCLKRST_RETENABLEN |
+ /* Enable ref clock for SS function */
+ PHYCLKRST_REF_SSP_EN |
+ /* Enable spread spectrum */
+ PHYCLKRST_SSC_EN |
+ /* Power down HS Bias and PLL blocks in suspend mode */
+ PHYCLKRST_COMMONONN |
+ /* Reset the port */
+ PHYCLKRST_PORTRESET;
+
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ udelay(10);
+
+ reg &= ~PHYCLKRST_PORTRESET;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ clk_disable_unprepare(phy_drd->clk);
+
+ return 0;
+}
+
+static int exynos5_usbdrd_phy_exit(struct phy *phy)
+{
+ int ret;
+ u32 reg;
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+ ret = clk_prepare_enable(phy_drd->clk);
+ if (ret)
+ return ret;
+
+ reg = PHYUTMI_OTGDISABLE |
+ PHYUTMI_FORCESUSPEND |
+ PHYUTMI_FORCESLEEP;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMI);
+
+ /* Resetting the PHYCLKRST enable bits to reduce leakage current */
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+ reg &= ~(PHYCLKRST_REF_SSP_EN |
+ PHYCLKRST_SSC_EN |
+ PHYCLKRST_COMMONONN);
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+ /* Control PHYTEST to remove leakage current */
+ reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+ reg |= PHYTEST_POWERDOWN_SSP |
+ PHYTEST_POWERDOWN_HSP;
+ writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+
+ clk_disable_unprepare(phy_drd->clk);
+
+ return 0;
+}
+
+static int exynos5_usbdrd_phy_power_on(struct phy *phy)
+{
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+ dev_dbg(phy_drd->dev, "Request to power_on usbdrd_phy phy\n");
+
+ clk_prepare_enable(phy_drd->ref_clk);
+
+ /* Power-on PHY*/
+ inst->phy_cfg->phy_isol(inst, 0);
+
+ return 0;
+}
+
+static int exynos5_usbdrd_phy_power_off(struct phy *phy)
+{
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+ dev_dbg(phy_drd->dev, "Request to power_off usbdrd_phy phy\n");
+
+ /* Power-off the PHY */
+ inst->phy_cfg->phy_isol(inst, 1);
+
+ clk_disable_unprepare(phy_drd->ref_clk);
+
+ return 0;
+}
+
+static struct phy *exynos5_usbdrd_phy_xlate(struct device *dev,
+ struct of_phandle_args *args)
+{
+ struct exynos5_usbdrd_phy *phy_drd = dev_get_drvdata(dev);
+
+ if (WARN_ON(args->args[0] > EXYNOS5_DRDPHYS_NUM))
+ return ERR_PTR(-ENODEV);
+
+ return phy_drd->phys[args->args[0]].phy;
+}
+
+static struct phy_ops exynos5_usbdrd_phy_ops = {
+ .init = exynos5_usbdrd_phy_init,
+ .exit = exynos5_usbdrd_phy_exit,
+ .power_on = exynos5_usbdrd_phy_power_on,
+ .power_off = exynos5_usbdrd_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+const struct usbdrd_phy_config exynos5_usbdrd_phy_cfg[] = {
+ {
+ .id = EXYNOS5_DRDPHY_UTMI,
+ .phy_isol = exynos5_usbdrd_phy_isol,
+ .phy_init = exynos5_usbdrd_utmi_init,
+ .set_refclk = exynos5_usbdrd_utmi_set_refclk,
+ },
+ {
+ .id = EXYNOS5_DRDPHY_PIPE3,
+ .phy_isol = exynos5_usbdrd_phy_isol,
+ .phy_init = exynos5_usbdrd_pipe3_init,
+ .set_refclk = exynos5_usbdrd_pipe3_set_refclk,
+ },
+};
+
+const struct exynos5_usbdrd_phy_drvdata exynos5420_usbdrd_phy = {
+ .phy_cfg = exynos5_usbdrd_phy_cfg,
+};
+
+const struct exynos5_usbdrd_phy_drvdata exynos5250_usbdrd_phy = {
+ .phy_cfg = exynos5_usbdrd_phy_cfg,
+};
+
+static const struct of_device_id exynos5_usbdrd_phy_of_match[] = {
+ {
+ .compatible = "samsung,exynos5250-usbdrd-phy",
+ .data = &exynos5250_usbdrd_phy
+ }, {
+ .compatible = "samsung,exynos5420-usbdrd-phy",
+ .data = &exynos5420_usbdrd_phy
+ },
+ { },
+};
+
+static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *node = dev->of_node;
+ struct exynos5_usbdrd_phy *phy_drd;
+ struct phy_provider *phy_provider;
+ struct resource *res;
+ const struct of_device_id *match;
+ const struct exynos5_usbdrd_phy_drvdata *drv_data;
+ struct regmap *reg_pmu;
+ u32 pmu_offset;
+ unsigned long ref_rate;
+ int i, ret;
+
+ phy_drd = devm_kzalloc(dev, sizeof(*phy_drd), GFP_KERNEL);
+ if (!phy_drd)
+ return -ENOMEM;
+
+ dev_set_drvdata(dev, phy_drd);
+ phy_drd->dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phy_drd->reg_phy = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy_drd->reg_phy))
+ return PTR_ERR(phy_drd->reg_phy);
+
+ match = of_match_node(exynos5_usbdrd_phy_of_match, pdev->dev.of_node);
+
+ drv_data = match->data;
+ phy_drd->drv_data = drv_data;
+
+ phy_drd->clk = devm_clk_get(dev, "phy");
+ if (IS_ERR(phy_drd->clk)) {
+ dev_err(dev, "Failed to get clock of phy controller\n");
+ return PTR_ERR(phy_drd->clk);
+ }
+
+ phy_drd->ref_clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(phy_drd->ref_clk)) {
+ dev_err(dev, "Failed to get reference clock of usbdrd phy\n");
+ return PTR_ERR(phy_drd->ref_clk);
+ }
+ ref_rate = clk_get_rate(phy_drd->ref_clk);
+
+ ret = exynos5_rate_to_clk(ref_rate, &phy_drd->extrefclk);
+ if (ret) {
+ dev_err(phy_drd->dev, "Clock rate (%ld) not supported\n",
+ ref_rate);
+ return ret;
+ }
+
+ reg_pmu = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "samsung,pmu-syscon");
+ if (IS_ERR(reg_pmu)) {
+ dev_err(dev, "Failed to map PMU register (via syscon)\n");
+ return PTR_ERR(reg_pmu);
+ }
+
+ ret = of_property_read_u32(node, "samsung,pmu-offset", &pmu_offset);
+ if (ret) {
+ dev_err(dev, "Missing pmu-offset for phy isolation\n");
+ return ret;
+ }
+
+ dev_vdbg(dev, "Creating usbdrd_phy phy\n");
+
+ for (i = 0; i < EXYNOS5_DRDPHYS_NUM; i++) {
+ struct phy *phy = devm_phy_create(dev, &exynos5_usbdrd_phy_ops,
+ NULL);
+ if (IS_ERR(phy)) {
+ dev_err(dev, "Failed to create usbdrd_phy phy\n");
+ return PTR_ERR(phy);
+ }
+
+ phy_drd->phys[i].phy = phy;
+ phy_drd->phys[i].index = i;
+ phy_drd->phys[i].reg_pmu = reg_pmu;
+ phy_drd->phys[i].pmu_offset = pmu_offset;
+ phy_drd->phys[i].phy_cfg = &drv_data->phy_cfg[i];
+ phy_set_drvdata(phy, &phy_drd->phys[i]);
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev,
+ exynos5_usbdrd_phy_xlate);
+ if (IS_ERR(phy_provider)) {
+ dev_err(phy_drd->dev, "Failed to register phy provider\n");
+ return PTR_ERR(phy_provider);
+ }
+
+ return 0;
+}
+
+static struct platform_driver exynos5_usb3drd_phy = {
+ .probe = exynos5_usbdrd_phy_probe,
+ .driver = {
+ .of_match_table = exynos5_usbdrd_phy_of_match,
+ .name = "exynos5_usb3drd_phy",
+ .owner = THIS_MODULE,
+ }
+};
+
+module_platform_driver(exynos5_usb3drd_phy);
+MODULE_DESCRIPTION("Samsung EXYNOS5 SoCs USB 3.0 DRD controller PHY driver");
+MODULE_AUTHOR("Vivek Gautam <gautam.vivek@xxxxxxxxxxx>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:exynos5_usb3drd_phy");
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
