Re: [PATCH V4 1/5] phy: Add new Exynos5 USB 3.0 PHY driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,


On Fri, Apr 25, 2014 at 1:27 PM, Tushar Behera <tushar.behera@xxxxxxxxxx> wrote:
> On 04/14/2014 08:07 PM, Sylwester Nawrocki wrote:
>> On 08/04/14 16:36, Vivek Gautam wrote:
>>> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
>>> index 28f9edb..6d99ba9 100644
>>> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
>>> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
>>> @@ -74,3 +74,45 @@ phy-consumer@12340000 {
>>>
>>>  Refer to DT bindings documentation of particular PHY consumer devices for more
>>>  information about required PHYs and the way of specification.
>>> +
>>> +Samsung Exynos5 SoC series USB DRD PHY controller
>>> +--------------------------------------------------
>>> +
>>> +Required properties:
>>> +- compatible : Should be set to one of the following supported values:
>>> +    - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC,
>>> +    - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC.
>>> +- reg : Register offset and length of USB DRD PHY register set;
>>> +- clocks: Clock IDs array as required by the controller
>>> +- clock-names: names of clocks correseponding to IDs in the clock property;
>>> +           Required clocks:
>>> +    - phy: main PHY clock (same as USB DRD controller i.e. DWC3 IP clock),
>>> +           used for register access.
>>> +    - ref: PHY's reference clock (usually crystal clock), associated by
>>> +           phy name, used to determine bit values for clock settings
>>> +           register.
>>> +    Additional clock required for Exynos5420:
>>> +    - usb30_sclk_100m: Additional special clock used for PHY operation
>>> +                       depicted as 'sclk_usbphy30' in CMU of Exynos5420.
>>> +- samsung,syscon-phandle: phandle for syscon interface, which is used to
>>> +                      control pmu registers for power isolation.
>>
>> Why to append "-phandle" to the property's name ? If this is for PMU
>> perhaps make it more explicit and name it: samsung,pmu-syscon or
>> samsung,pmureg ?
>>
>
> There are already a couple of nodes (watchdog and sata) using
> samsung,syscon-phandle. IMHO, we should keep only property string for
> syscon node. Either we keep syscon-phandle here or change sata/watchdog
> driver to use the modified property name.

IMHO samsung,pmu-syscon make more sense rather than appending a
'-phandle' to the property name.
This is a 'phandle' and that is in fact understood, isn't it ?
We can change in the watchdog, sata drivers to use use the modified name.
I can send a patch for the same if we are OK with this, so that we
maintain the consistency in the device tree.


-- 
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux