Hi Kishon, On Thu, Apr 10, 2014 at 2:39 PM, Kishon Vijay Abraham I <kishon@xxxxxx> wrote: > Hi. > > On Wednesday 09 April 2014 05:24 PM, Vivek Gautam wrote: >> Adding support to enable/disable VBUS hooked to a gpio >> to enable vbus supply on the port. >> >> Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx> >> --- >> >> Based on 'phy-exynos5-usbdrd' patches: >> [PATCH V4 0/5] Add Exynos5 USB 3.0 phy driver based on generic PHY framework >> http://www.spinics.net/lists/linux-usb/msg105507.html >> >> drivers/phy/phy-exynos5-usbdrd.c | 18 ++++++++++++++++++ >> 1 file changed, 18 insertions(+) >> >> diff --git a/drivers/phy/phy-exynos5-usbdrd.c b/drivers/phy/phy-exynos5-usbdrd.c >> index ff54a7c..5ca7485 100644 >> --- a/drivers/phy/phy-exynos5-usbdrd.c >> +++ b/drivers/phy/phy-exynos5-usbdrd.c >> @@ -18,6 +18,7 @@ >> #include <linux/module.h> >> #include <linux/of.h> >> #include <linux/of_address.h> >> +#include <linux/of_gpio.h> >> #include <linux/phy/phy.h> >> #include <linux/platform_device.h> >> #include <linux/mutex.h> >> @@ -176,6 +177,7 @@ struct exynos5_usbdrd_phy { >> struct clk *ref_clk; >> unsigned long ref_rate; >> unsigned int refclk_reg; >> + int gpio; >> }; >> >> #define to_usbdrd_phy(inst) \ >> @@ -460,6 +462,9 @@ static int exynos5_usbdrd_phy_power_on(struct phy *phy) >> if (!IS_ERR(phy_drd->usb30_sclk)) >> clk_prepare_enable(phy_drd->usb30_sclk); >> >> + /* Toggle VBUS gpio - on */ >> + gpio_set_value(phy_drd->gpio, 1); >> + >> /* Power-on PHY*/ >> inst->phy_cfg->phy_isol(inst, 0); >> >> @@ -476,6 +481,9 @@ static int exynos5_usbdrd_phy_power_off(struct phy *phy) >> /* Power-off the PHY */ >> inst->phy_cfg->phy_isol(inst, 1); >> >> + /* Toggle VBUS gpio - off */ >> + gpio_set_value(phy_drd->gpio, 0); >> + >> if (!IS_ERR(phy_drd->usb30_sclk)) >> clk_disable_unprepare(phy_drd->usb30_sclk); >> >> @@ -585,6 +593,16 @@ static int exynos5_usbdrd_phy_probe(struct platform_device *pdev) >> >> phy_drd->drv_data = drv_data; >> >> + /* Get required GPIO for vbus */ >> + phy_drd->gpio = of_get_named_gpio(dev->of_node, >> + "samsung,vbus-gpio", 0); > > Is this dt property documented somewhere? >> + if (!gpio_is_valid(phy_drd->gpio)) >> + dev_dbg(dev, "no usbdrd-phy vbus gpio defined\n"); > > No return here? Can the PHY be functional even without the VBUS? On few boards, the switch IC's enable may no be controlled by a GPIO, rather enabled by default. So in those cases we may not want to stop PHY probe, when the VBUS GPIO is not present. -- Best Regards Vivek Gautam Samsung R&D Institute, Bangalore India -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
