Hi Denis, On Fri, Mar 7, 2014 at 2:04 PM, Denis Carikli <denis@xxxxxxxxxx> wrote: > +static int usbmisc_imx25_init(struct imx_usbmisc_data *data) > +{ > + void __iomem *reg = NULL; This variable is not used and causes a warning. Please remove it. After applying this patch things go further when I boot with a USB thumb connected to the USB Host1 port: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage 53ff4400.usb supply vbus not found, using dummy regulator ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected .... usb 1-1: new full-speed USB device number 2 using ci_hdrc (Not sure why it says full-speed device. When I connect the same device to a PC it says high-speed) usb 1-1: not running at top speed; connect to a high speed hub usb-storage 1-1:1.0: USB Mass Storage device detected usb-storage 1-1:1.0: Quirks match for vid 0457 pid 0151: 80 scsi0 : usb-storage 1-1:1.0 scsi 0:0:0:0: Direct-Access Ut163 USB2FlashStorage 0.00 PQ: 0 ANSI: 2 sd 0:0:0:0: [sda] 248000 512-byte logical blocks: (126 MB/121 MiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Asking for cache data failed sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Asking for cache data failed sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] Asking for cache data failed sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Attached SCSI removable disk fec 50038000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx Sending DHCP requests ., OK IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.8 IP-Config: Complete: device=eth0, hwaddr=00:04:00:00:00:00, ipaddr=192.168.0.8, mask=255.255.251 host=192.168.0.8, domain=, nis-domain=(none) bootserver=192.168.0.1, rootserver=192.168.0.2, rootpath= nameserver0=192.168.0.1 ALSA device list: No soundcards found. VFS: Mounted root (nfs filesystem) readonly on device 0:13. devtmpfs: mounted Freeing unused kernel memory: 276K (c0697000 - c06dc000) starting pid 536, tty '': '/etc/rc.d/rcS' Mounting /proc and /sys Starting the hotplug events dispatcher udevd Synthesizing initial hotplug events imx-sdma 53fd4000.sdma: firmware not found (Then system hangs here). If I boot without the USB thumb connected, then I reach the prompt, however after inserting the USB pen drive into USBH1 there is no detection. Any ideas? Thanks, Fabio Estevam -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html