On 03/04/2014 06:28 PM, Tony Lindgren wrote: > * Roger Quadros <rogerq@xxxxxx> [140304 01:17]: >> Hi Tony, >> >> On 03/03/2014 09:02 PM, Tony Lindgren wrote: >>> * Roger Quadros <rogerq@xxxxxx> [140303 07:10]: >>>> Move omap-control binding information to the right location. >>>> >>>> Signed-off-by: Roger Quadros <rogerq@xxxxxx> >>>> --- >>>> Documentation/devicetree/bindings/phy/ti-phy.txt | 25 ++++++++++++++++++++++ >>>> Documentation/devicetree/bindings/usb/omap-usb.txt | 24 --------------------- >>>> 2 files changed, 25 insertions(+), 24 deletions(-) >>>> >>>> diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt >>>> index 207e14c..41dc132 100644 >>>> --- a/Documentation/devicetree/bindings/phy/ti-phy.txt >>>> +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt >>>> @@ -1,5 +1,30 @@ >>>> TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs >>>> >>>> +OMAP CONTROL PHY >>>> + >>>> +Required properties: >>>> + - compatible: Should be one of >>>> + "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. >>>> + "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register >>>> + e.g. USB2_PHY on OMAP5. >>>> + "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control >>>> + e.g. USB3 PHY and SATA PHY on OMAP5. >>>> + "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on >>>> + DRA7 platform. >>>> + "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on >>>> + AM437 platform. >>> >>> To me it seems that you can leave out all the above. You can set these falgs >>> flags directly in the driver based on the compatible flag. Then just initialize >>> the .data in the driver based on the compatible flag. >> >> I'm not sure if I got you. A single platform can have different type of phys. >> >> e.g. OMAP5 has both usb2 and pipe3 PHYs, >> DRA7 has both pipe3 and usb2 PHYs, but this usb2 PHY is not compatible with OMAP5 one >> so we need a new compatible id for that. >> >> To add to the woes, the designers were creative enough to make another mutation to >> the USB2 PHY for AM437x, :( > > Oh OK, in that case the compatible flag may not be enough for configuring the > various instances. > >> What do you suggest the compatible ids should look like for these 5 types of PHY control? >> OTGHS (OMAP4 & 5) >> USB2 (OMAP5) >> PIPE3 (OMAP5 & DRA7) >> USB2x (DRA7) >> USB2y (AM437) > > I think in that case having the various instances fully configurable from > device tree is OK if you prefer that. But if you wanted to use the > compatible flag, then you could do something like this: I'll stick to the compatible flag. > > ti,control-phy-omap4-otghs (assuming same on omap4 & 5) > ti,control-phy-omap5-usb2 > ti,control-phy-omap5-pipe3 (assuming same on omap5 & dra7) > ti,control-phy-dra7-usb2x > ti,control-phy-am437-usb2y OK. The last 2 can just be ti,control-phy-dra7-usb2 ti,control-phy-am437-usb2 cheers, -roger -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
