High-speed USB connections revert back to full-speed signalling when
the device goes into suspend. This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.
On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state. It generates a false wakeup signal,
which can prevent the controller from going to sleep.
To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling. (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: Alan Stern <stern@xxxxxxxxxxxxxxxxxxx>
Reviewed-by: Peter Chen <Peter.Chen@xxxxxxxxxxxxx>
CC: <stable@xxxxxxxxxxxxxxx>
---
[as1740]
drivers/usb/host/ehci-hub.c | 26 ++++++++++++++++++++++----
1 file changed, 22 insertions(+), 4 deletions(-)
Index: usb-3.14/drivers/usb/host/ehci-hub.c
===================================================================
--- usb-3.14.orig/drivers/usb/host/ehci-hub.c
+++ usb-3.14/drivers/usb/host/ehci-hub.c
@@ -238,6 +238,7 @@ static int ehci_bus_suspend (struct usb_
int port;
int mask;
int changed;
+ bool fs_idle_delay;
ehci_dbg(ehci, "suspend root hub\n");
@@ -272,6 +273,7 @@ static int ehci_bus_suspend (struct usb_
ehci->bus_suspended = 0;
ehci->owned_ports = 0;
changed = 0;
+ fs_idle_delay = false;
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status [port];
@@ -300,16 +302,32 @@ static int ehci_bus_suspend (struct usb_
}
if (t1 != t2) {
+ /*
+ * On some controllers, Wake-On-Disconnect will
+ * generate false wakeup signals until the bus
+ * switches over to full-speed idle. For their
+ * sake, add a delay if we need one.
+ */
+ if ((t2 & PORT_WKDISC_E) &&
+ ehci_port_speed(ehci, t2) ==
+ USB_PORT_STAT_HIGH_SPEED)
+ fs_idle_delay = true;
ehci_writel(ehci, t2, reg);
changed = 1;
}
}
+ spin_unlock_irq(&ehci->lock);
+
+ if ((changed && ehci->has_tdi_phy_lpm) || fs_idle_delay) {
+ /*
+ * Wait for HCD to enter low-power mode or for the bus
+ * to switch to full-speed idle.
+ */
+ usleep_range(5000, 5500);
+ }
if (changed && ehci->has_tdi_phy_lpm) {
- spin_unlock_irq(&ehci->lock);
- msleep(5); /* 5 ms for HCD to enter low-power mode */
spin_lock_irq(&ehci->lock);
-
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *hostpc_reg = &ehci->regs->hostpc[port];
@@ -322,8 +340,8 @@ static int ehci_bus_suspend (struct usb_
port, (t3 & HOSTPC_PHCD) ?
"succeeded" : "failed");
}
+ spin_unlock_irq(&ehci->lock);
}
- spin_unlock_irq(&ehci->lock);
/* Apparently some devices need a >= 1-uframe delay here */
if (ehci->bus_suspended)
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
