Update the documentation to reflect the new ABI requirements and how to
use the byte index with the mask properly to check event status.
Signed-off-by: Beau Belgrave <beaub@xxxxxxxxxxxxxxxxxxx>
---
Documentation/trace/user_events.rst | 86 +++++++++++++++++++----------
1 file changed, 58 insertions(+), 28 deletions(-)
diff --git a/Documentation/trace/user_events.rst b/Documentation/trace/user_events.rst
index c180936f49fc..9f181f342a70 100644
--- a/Documentation/trace/user_events.rst
+++ b/Documentation/trace/user_events.rst
@@ -20,14 +20,14 @@ dynamic_events is the same as the ioctl with the u: prefix applied.
Typically programs will register a set of events that they wish to expose to
tools that can read trace_events (such as ftrace and perf). The registration
-process gives back two ints to the program for each event. The first int is the
-status index. This index describes which byte in the
+process gives back two ints to the program for each event. The first int is
+the status bit. This describes which bit in little-endian format in the
/sys/kernel/debug/tracing/user_events_status file represents this event. The
-second int is the write index. This index describes the data when a write() or
+second int is the write index which describes the data when a write() or
writev() is called on the /sys/kernel/debug/tracing/user_events_data file.
-The structures referenced in this document are contained with the
-/include/uap/linux/user_events.h file in the source tree.
+The structures referenced in this document are contained within the
+/include/uapi/linux/user_events.h file in the source tree.
**NOTE:** *Both user_events_status and user_events_data are under the tracefs
filesystem and may be mounted at different paths than above.*
@@ -38,18 +38,18 @@ Registering within a user process is done via ioctl() out to the
/sys/kernel/debug/tracing/user_events_data file. The command to issue is
DIAG_IOCSREG.
-This command takes a struct user_reg as an argument::
+This command takes a packed struct user_reg as an argument::
struct user_reg {
u32 size;
u64 name_args;
- u32 status_index;
+ u32 status_bit;
u32 write_index;
};
The struct user_reg requires two inputs, the first is the size of the structure
to ensure forward and backward compatibility. The second is the command string
-to issue for registering. Upon success two outputs are set, the status index
+to issue for registering. Upon success two outputs are set, the status bit
and the write index.
User based events show up under tracefs like any other event under the
@@ -111,15 +111,56 @@ in realtime. This allows user programs to only incur the cost of the write() or
writev() calls when something is actively attached to the event.
User programs call mmap() on /sys/kernel/debug/tracing/user_events_status to
-check the status for each event that is registered. The byte to check in the
-file is given back after the register ioctl() via user_reg.status_index.
+check the status for each event that is registered. The bit to check in the
+file is given back after the register ioctl() via user_reg.status_bit. The bit
+is always in little-endian format. Programs can check if the bit is set either
+using a byte-wise index with a mask or a long-wise index with a little-endian
+mask.
+
Currently the size of user_events_status is a single page, however, custom
kernel configurations can change this size to allow more user based events. In
all cases the size of the file is a multiple of a page size.
-For example, if the register ioctl() gives back a status_index of 3 you would
-check byte 3 of the returned mmap data to see if anything is attached to that
-event.
+For example, if the register ioctl() gives back a status_bit of 3 you would
+check byte 0 (3 / 8) of the returned mmap data and then AND the result with 8
+(1 << (3 % 8)) to see if anything is attached to that event.
+
+A byte-wise index check is performed as follows::
+
+ int index, mask;
+ char *status_page;
+
+ index = status_bit / 8;
+ mask = 1 << (status_bit % 8);
+
+ ...
+
+ if (status_page[index] & mask) {
+ /* Enabled */
+ }
+
+A long-wise index check is performed as follows::
+
+ #include <asm/bitsperlong.h>
+ #include <endian.h>
+
+ #if __BITS_PER_LONG == 64
+ #define endian_swap(x) htole64(x)
+ #else
+ #define endian_swap(x) htole32(x)
+ #endif
+
+ long index, mask, *status_page;
+
+ index = status_bit / __BITS_PER_LONG;
+ mask = 1L << (status_bit % __BITS_PER_LONG);
+ mask = endian_swap(mask);
+
+ ...
+
+ if (status_page[index] & mask) {
+ /* Enabled */
+ }
Administrators can easily check the status of all registered events by reading
the user_events_status file directly via a terminal. The output is as follows::
@@ -137,7 +178,7 @@ For example, on a system that has a single event the output looks like this::
Active: 1
Busy: 0
- Max: 4096
+ Max: 32768
If a user enables the user event via ftrace, the output would change to this::
@@ -145,21 +186,10 @@ If a user enables the user event via ftrace, the output would change to this::
Active: 1
Busy: 1
- Max: 4096
-
-**NOTE:** *A status index of 0 will never be returned. This allows user
-programs to have an index that can be used on error cases.*
-
-Status Bits
-^^^^^^^^^^^
-The byte being checked will be non-zero if anything is attached. Programs can
-check specific bits in the byte to see what mechanism has been attached.
-
-The following values are defined to aid in checking what has been attached:
-
-**EVENT_STATUS_FTRACE** - Bit set if ftrace has been attached (Bit 0).
+ Max: 32768
-**EVENT_STATUS_PERF** - Bit set if perf has been attached (Bit 1).
+**NOTE:** *A status bit of 0 will never be returned. This allows user programs
+to have a bit that can be used on error cases.*
Writing Data
------------
--
2.25.1
|