The following commit has been merged into the timers/urgent branch of tip: Commit-ID: 2a97d55333e4299f32c98cca6dc5c4db1c5855fc Gitweb: https://git.kernel.org/tip/2a97d55333e4299f32c98cca6dc5c4db1c5855fc Author: Geert Uytterhoeven <geert+renesas@xxxxxxxxx> AuthorDate: Thu, 10 Dec 2020 20:46:48 +01:00 Committer: Daniel Lezcano <daniel.lezcano@xxxxxxxxxx> CommitterDate: Mon, 18 Jan 2021 16:20:37 +01:00 clocksource/drivers/sh_cmt: Make sure channel clock supply is enabled The Renesas Compare Match Timer 0 and 1 (CMT0/1) variants have a register to control the clock supply to the individual channels. Currently the driver does not touch this register, and relies on the documented initial value, which has the clock supply enabled for all channels present. However, when Linux starts on the APE6-EVM development board, only the clock supply to the first CMT1 channel is enabled. Hence the first channel (used as a clockevent) works, while the second channel (used as a clocksource) does not. Note that the default system clocksource is the Cortex-A15 architectured timer, and the user needs to manually switch to the CMT1 clocksource to trigger the broken behavior. Fix this by removing the fragile dependency on implicit reset and/or boot loader state, and by enabling the clock supply explicitly for all channels used instead. This requires postponing the clk_disable() call, else the timer's registers cannot be accessed in sh_cmt_setup_channel(). Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx> Signed-off-by: Daniel Lezcano <daniel.lezcano@xxxxxxxxxx> Link: https://lore.kernel.org/r/20201210194648.2901899-1-geert+renesas@xxxxxxxxx --- drivers/clocksource/sh_cmt.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) diff --git a/drivers/clocksource/sh_cmt.c b/drivers/clocksource/sh_cmt.c index e258230..c98f885 100644 --- a/drivers/clocksource/sh_cmt.c +++ b/drivers/clocksource/sh_cmt.c @@ -235,6 +235,8 @@ static const struct sh_cmt_info sh_cmt_info[] = { #define CMCNT 1 /* channel register */ #define CMCOR 2 /* channel register */ +#define CMCLKE 0x1000 /* CLK Enable Register (R-Car Gen2) */ + static inline u32 sh_cmt_read_cmstr(struct sh_cmt_channel *ch) { if (ch->iostart) @@ -853,6 +855,7 @@ static int sh_cmt_setup_channel(struct sh_cmt_channel *ch, unsigned int index, unsigned int hwidx, bool clockevent, bool clocksource, struct sh_cmt_device *cmt) { + u32 value; int ret; /* Skip unused channels. */ @@ -882,6 +885,11 @@ static int sh_cmt_setup_channel(struct sh_cmt_channel *ch, unsigned int index, ch->iostart = cmt->mapbase + ch->hwidx * 0x100; ch->ioctrl = ch->iostart + 0x10; ch->timer_bit = 0; + + /* Enable the clock supply to the channel */ + value = ioread32(cmt->mapbase + CMCLKE); + value |= BIT(hwidx); + iowrite32(value, cmt->mapbase + CMCLKE); break; } @@ -1014,12 +1022,10 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev) else cmt->rate = clk_get_rate(cmt->clk) / 8; - clk_disable(cmt->clk); - /* Map the memory resource(s). */ ret = sh_cmt_map_memory(cmt); if (ret < 0) - goto err_clk_unprepare; + goto err_clk_disable; /* Allocate and setup the channels. */ cmt->num_channels = hweight8(cmt->hw_channels); @@ -1047,6 +1053,8 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev) mask &= ~(1 << hwidx); } + clk_disable(cmt->clk); + platform_set_drvdata(pdev, cmt); return 0; @@ -1054,6 +1062,8 @@ static int sh_cmt_setup(struct sh_cmt_device *cmt, struct platform_device *pdev) err_unmap: kfree(cmt->channels); iounmap(cmt->mapbase); +err_clk_disable: + clk_disable(cmt->clk); err_clk_unprepare: clk_unprepare(cmt->clk); err_clk_put:
![]() |