Re: [PATCH v12 8/8] PCI: endpoint: Remove "core_init_notifier" flag

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Apr 12, 2024 at 03:22:16PM -0500, Bjorn Helgaas wrote:
> On Wed, Mar 27, 2024 at 02:43:37PM +0530, Manivannan Sadhasivam wrote:
> > "core_init_notifier" flag is set by the glue drivers requiring refclk from
> > the host to complete the DWC core initialization. Also, those drivers will
> > send a notification to the EPF drivers once the initialization is fully
> > completed using the pci_epc_init_notify() API. Only then, the EPF drivers
> > will start functioning.
> > 
> > For the rest of the drivers generating refclk locally, EPF drivers will
> > start functioning post binding with them. EPF drivers rely on the
> > 'core_init_notifier' flag to differentiate between the drivers.
> > Unfortunately, this creates two different flows for the EPF drivers.
> > 
> > So to avoid that, let's get rid of the "core_init_notifier" flag and follow
> > a single initialization flow for the EPF drivers. This is done by calling
> > the dw_pcie_ep_init_notify() from all glue drivers after the completion of
> > dw_pcie_ep_init_registers() API. This will allow all the glue drivers to
> > send the notification to the EPF drivers once the initialization is fully
> > completed.
> 
> Thanks for doing this!  I think this is a significantly nicer
> solution than core_init_notifier was.
> 
> One question: both qcom and tegra194 call dw_pcie_ep_init_registers()
> from an interrupt handler, but they register that handler in a
> different order with respect to dw_pcie_ep_init().
> 
> I don't know what actually starts the process that leads to the
> interrupt, but if it's dw_pcie_ep_init(), then one of these (qcom, I
> think) must be racy:
> 

Your analysis is correct. But there is no race observed as of now since the IRQ
will only be enabled by configuring the endpoint using configfs interface and
right now I use an init script to do that. By that time, the driver would've
already probed completely.

But there is a slight chance that if the driver gets loaded as a module and the
userspace script starts configuring the endpoint interface using inotify watch
or something similar, then race could occur since the IRQ handler may not be
registered at that point.

>   qcom_pcie_ep_probe
>     dw_pcie_ep_init                                             <- A
>     qcom_pcie_ep_enable_irq_resources
>       devm_request_threaded_irq(qcom_pcie_ep_perst_irq_thread)  <- B
> 
>   qcom_pcie_ep_perst_irq_thread
>     qcom_pcie_perst_deassert
>       dw_pcie_ep_init_registers
> 
>   tegra_pcie_dw_probe
>     tegra_pcie_config_ep
>       devm_request_threaded_irq(tegra_pcie_ep_pex_rst_irq)      <- B
>       dw_pcie_ep_init                                           <- A
> 
>   tegra_pcie_ep_pex_rst_irq
>     pex_ep_event_pex_rst_deassert
>       dw_pcie_ep_init_registers
> 
> Whatever the right answer is, I think qcom and tegra194 should both
> order dw_pcie_ep_init() and the devm_request_threaded_irq() the same
> way.
> 

Agree. The right way is to register the IRQ handler first and then do
dw_pcie_ep_init(). I will fix it in the qcom driver.

Thanks for spotting!

- Mani

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux