From: Thierry Reding <treding@xxxxxxxxxx>
The pad configuration node schema in its current form can accidentally
match other properties as well. Restructure the schema to better match
how the device trees are using these.
Signed-off-by: Thierry Reding <treding@xxxxxxxxxx>
---
.../arm/tegra/nvidia,tegra20-pmc.yaml | 181 ++++++++++++------
1 file changed, 120 insertions(+), 61 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml
index 82070d47ac7c..271aa8f80a65 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml
@@ -245,69 +245,82 @@ properties:
- resets
- '#power-domain-cells'
-patternProperties:
- "^[a-f0-9]+-[a-f0-9]+$":
+ pinmux:
type: object
- description:
- This is a Pad configuration node. On Tegra SOCs a pad is a set of
- pins which are configured as a group. The pin grouping is a fixed
- attribute of the hardware. The PMC can be used to set pad power state
- and signaling voltage. A pad can be either in active or power down mode.
- The support for power state and signaling voltage configuration varies
- depending on the pad in question. 3.3V and 1.8V signaling voltages
- are supported on pins where software controllable signaling voltage
- switching is available.
-
- The pad configuration state nodes are placed under the pmc node and they
- are referred to by the pinctrl client properties. For more information
- see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
- The pad name should be used as the value of the pins property in pin
- configuration nodes.
-
- The following pads are present on Tegra124 and Tegra132
- audio, bb, cam, comp, csia, csb, cse, dsi, dsib, dsic, dsid, hdmi, hsic,
- hv, lvds, mipi-bias, nand, pex-bias, pex-clk1, pex-clk2, pex-cntrl,
- sdmmc1, sdmmc3, sdmmc4, sys_ddc, uart, usb0, usb1, usb2, usb_bias.
-
- The following pads are present on Tegra210
- audio, audio-hv, cam, csia, csib, csic, csid, csie, csif, dbg,
- debug-nonao, dmic, dp, dsi, dsib, dsic, dsid, emmc, emmc2, gpio, hdmi,
- hsic, lvds, mipi-bias, pex-bias, pex-clk1, pex-clk2, pex-cntrl, sdmmc1,
- sdmmc3, spi, spi-hv, uart, usb0, usb1, usb2, usb3, usb-bias.
-
properties:
- pins:
- $ref: /schemas/types.yaml#/definitions/string
- description: Must contain name of the pad(s) to be configured.
-
- low-power-enable:
- $ref: /schemas/types.yaml#/definitions/flag
- description: Configure the pad into power down mode.
-
- low-power-disable:
- $ref: /schemas/types.yaml#/definitions/flag
- description: Configure the pad into active mode.
-
- power-source:
- $ref: /schemas/types.yaml#/definitions/uint32
- description:
- Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
- TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
- The values are defined in
- include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
- Power state can be configured on all Tegra124 and Tegra132
- pads. None of the Tegra124 or Tegra132 pads support signaling
- voltage switching.
- All of the listed Tegra210 pads except pex-cntrl support power
- state configuration. Signaling voltage switching is supported
- on below Tegra210 pads.
- audio, audio-hv, cam, dbg, dmic, gpio, pex-cntrl, sdmmc1,
- sdmmc3, spi, spi-hv, and uart.
-
- required:
- - pins
-
- additionalProperties: false
+ status: true
+
+ additionalProperties:
+ type: object
+ description: |
+ This is a pad configuration node. On Tegra SoCs a pad is a set of pins
+ which are configured as a group. The pin grouping is a fixed attribute
+ of the hardware. The PMC can be used to set pad power state and
+ signaling voltage. A pad can be either in active or power down mode.
+ The support for power state and signaling voltage configuration varies
+ depending on the pad in question. 3.3V and 1.8V signaling voltages are
+ supported on pins where software controllable signaling voltage
+ switching is available.
+
+ The pad configuration state nodes are placed under the pmc node and
+ they are referred to by the pinctrl client properties. For more
+ information see:
+
+ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+ The pad name should be used as the value of the pins property in pin
+ configuration nodes.
+
+ The following pads are present on Tegra124 and Tegra132:
+
+ audio, bb, cam, comp, csia, csb, cse, dsi, dsib, dsic, dsid, hdmi,
+ hsic, hv, lvds, mipi-bias, nand, pex-bias, pex-clk1, pex-clk2,
+ pex-cntrl, sdmmc1, sdmmc3, sdmmc4, sys_ddc, uart, usb0, usb1, usb2,
+ usb_bias
+
+ The following pads are present on Tegra210:
+
+ audio, audio-hv, cam, csia, csib, csic, csid, csie, csif, dbg,
+ debug-nonao, dmic, dp, dsi, dsib, dsic, dsid, emmc, emmc2, gpio,
+ hdmi, hsic, lvds, mipi-bias, pex-bias, pex-clk1, pex-clk2, pex-cntrl,
+ sdmmc1, sdmmc3, spi, spi-hv, uart, usb0, usb1, usb2, usb3, usb-bias
+ additionalProperties: false
+ properties:
+ pins:
+ $ref: /schemas/types.yaml#/definitions/string-array
+ description: Must contain name of the pad(s) to be configured.
+
+ low-power-enable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: Configure the pad into power down mode.
+
+ low-power-disable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: Configure the pad into active mode.
+
+ power-source:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
+ TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages. The
+ values are defined in:
+
+ include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
+
+ Power state can be configured on all Tegra124 and Tegra132 pads.
+ None of the Tegra124 or Tegra132 pads support signaling voltage
+ switching. All of the listed Tegra210 pads except pex-cntrl support
+ power state configuration. Signaling voltage switching is supported
+ on the following Tegra210 pads:
+
+ audio, audio-hv, cam, dbg, dmic, gpio, pex-cntrl, sdmmc1, sdmmc3,
+ spi, spi-hv, uart
+
+ phandle:
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ required:
+ - pins
required:
- compatible
@@ -316,6 +329,52 @@ required:
- clocks
- '#clock-cells'
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra124-pmc
+ then:
+ properties:
+ pinmux:
+ properties:
+ status: true
+
+ additionalProperties:
+ type: object
+ properties:
+ pins:
+ items:
+ enum: [ audio, bb, cam, comp, csia, csb, cse, dsi, dsib,
+ dsic, dsid, hdmi, hsic, hv, lvds, mipi-bias, nand,
+ pex-bias, pex-clk1, pex-clk2, pex-cntrl, sdmmc1,
+ sdmmc3, sdmmc4, sys_ddc, uart, usb0, usb1, usb2,
+ usb_bias ]
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra210-pmc
+ then:
+ properties:
+ pinmux:
+ properties:
+ status: true
+
+ additionalProperties:
+ type: object
+ properties:
+ pins:
+ items:
+ enum: [ audio, audio-hv, cam, csia, csib, csic, csid, csie,
+ csif, dbg, debug-nonao, dmic, dp, dsi, dsib, dsic,
+ dsid, emmc, emmc2, gpio, hdmi, hsic, lvds, mipi-bias,
+ pex-bias, pex-clk1, pex-clk2, pex-cntrl, sdmmc1,
+ sdmmc3, spi, spi-hv, uart, usb0, usb1, usb2, usb3,
+ usb-bias ]
+
additionalProperties: false
dependencies:
--
2.41.0
