Re: [PATCH v3 28/65] clk: renesas: r9a06g032: Add a determine_rate hook

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Geert & Maxime,

geert@xxxxxxxxxxxxxx wrote on Tue, 11 Apr 2023 12:27:38 +0200:

> CC Gareth, Hervé, Miquel, Ralph
> 
> On Tue, Apr 4, 2023 at 2:44 PM Maxime Ripard <maxime@xxxxxxxxxx> wrote:
> > The Renesas r9a06g032 bitselect clock implements a mux with a set_parent
> > hook, but doesn't provide a determine_rate implementation.
> >
> > This is a bit odd, since set_parent() is there to, as its name implies,
> > change the parent of a clock. However, the most likely candidate to
> > trigger that parent change is a call to clk_set_rate(), with
> > determine_rate() figuring out which parent is the best suited for a
> > given rate.
> >
> > The other trigger would be a call to clk_set_parent(), but it's far less
> > used, and it doesn't look like there's any obvious user for that clock.
> >
> > So, the set_parent hook is effectively unused, possibly because of an
> > oversight. However, it could also be an explicit decision by the
> > original author to avoid any reparenting but through an explicit call to
> > clk_set_parent().
> >
> > The latter case would be equivalent to setting the flag
> > CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
> > to __clk_mux_determine_rate(). Indeed, if no determine_rate
> > implementation is provided, clk_round_rate() (through
> > clk_core_round_rate_nolock()) will call itself on the parent if
> > CLK_SET_RATE_PARENT is set, and will not change the clock rate
> > otherwise. __clk_mux_determine_rate() has the exact same behavior when
> > CLK_SET_RATE_NO_REPARENT is set.
> >
> > And if it was an oversight, then we are at least explicit about our
> > behavior now and it can be further refined down the line.
> >
> > Signed-off-by: Maxime Ripard <maxime@xxxxxxxxxx>  
> 
> LGTM, so
> Reviewed-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>

I searched for 'possible callers', I didn't find any places
where this would be used on the consumer side. However, downstream,
there is a rzn1-clock-bitselect.c clock driver which states:

+ * This clock provider handles the case of the RZN1 where you have peripherals
+ * that have two potential clock source and two gates, one for each of the
+ * clock source - the used clock source (for all sub clocks) is selected by a
+ * single bit.
+ * That single bit affects all sub-clocks, and therefore needs to change the
+ * active gate (and turn the others off) and force a recalculation of the rates.

I don't know how much of this file has been upstreamed (under a
different form) but this might very well be related to the fact that
reparenting in some cases would be a major issue and thus needs to be
avoided unless done on purpose (guessing?).

Maybe Ralph can comment, but for what I understand,

Reviewed-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>

> But I do not have the hardware.
> 
> > --- a/drivers/clk/renesas/r9a06g032-clocks.c
> > +++ b/drivers/clk/renesas/r9a06g032-clocks.c
> > @@ -1121,6 +1121,7 @@ static int r9a06g032_clk_mux_set_parent(struct clk_hw *hw, u8 index)
> >  }
> >
> >  static const struct clk_ops clk_bitselect_ops = {
> > +       .determine_rate = __clk_mux_determine_rate,
> >         .get_parent = r9a06g032_clk_mux_get_parent,
> >         .set_parent = r9a06g032_clk_mux_set_parent,
> >  };
> > @@ -1145,7 +1146,7 @@ r9a06g032_register_bitsel(struct r9a06g032_priv *clocks,
> >
> >         init.name = desc->name;
> >         init.ops = &clk_bitselect_ops;
> > -       init.flags = CLK_SET_RATE_PARENT;
> > +       init.flags = CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT;
> >         init.parent_names = names;
> >         init.num_parents = 2;
> >  
> 
> Gr{oetje,eeting}s,
> 
>                         Geert
> 

Thanks,
Miquèl




[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux