RE: [Patch V5 2/3] tpm_tis-spi: Support hardware wait polling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



> -----Original Message-----
> From: Jason Gunthorpe <jgg@xxxxxxxxxx>
> Sent: 28 February 2023 17:58
> To: Jarkko Sakkinen <jarkko@xxxxxxxxxx>
> Cc: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>; robh+dt@xxxxxxxxxx;
> broonie@xxxxxxxxxx; peterhuewe@xxxxxx;
> krzysztof.kozlowski+dt@xxxxxxxxxx; linux-spi@xxxxxxxxxxxxxxx; linux-
> tegra@xxxxxxxxxxxxxxx; linux-integrity@xxxxxxxxxxxxxxx; linux-
> kernel@xxxxxxxxxxxxxxx; thierry.reding@xxxxxxxxx; Jonathan Hunter
> <jonathanh@xxxxxxxxxx>; Sowjanya Komatineni
> <skomatineni@xxxxxxxxxx>; Laxman Dewangan <ldewangan@xxxxxxxxxx>
> Subject: Re: [Patch V5 2/3] tpm_tis-spi: Support hardware wait polling
> 
> On Tue, Feb 28, 2023 at 04:36:26AM +0200, Jarkko Sakkinen wrote:
> > On Mon, Feb 27, 2023 at 05:37:01PM +0530, Krishna Yarlagadda wrote:
> > > TPM devices raise wait signal on last addr cycle. This can be detected
> > > by software driver by reading MISO line on same clock which requires
> > > full duplex support. In case of half duplex controllers wait detection
> > > has to be implemented in HW.
> > > Support hardware wait state detection by sending entire message and let
> > > controller handle flow control.
> >
> > When a is started sentence with the word "support" it translates to "I'm
> > too lazy to write a proper and verbose description of the implementation"
> > :-)
> >
> > It has some abstract ideas of the implementation, I give you that, but do
> > you think anyone ever will get any value of reading that honestly? A bit
> > more concrette description of the change helps e.g. when bisecting bugs.
> 
> I would expect SPI_TPM_HW_FLOW to be documented in the kdocs to a
> level that any other HW could implement it as well.
HW implementation can be controller specific. I would add comments in the
header to say CMD-ADDR-DATA is sent as single message with this flag.
> 
> > > +int tpm_tis_spi_transfer(struct tpm_tis_data *data, u32 addr, u16 len,
> > > +			 u8 *in, const u8 *out)
> > > +{
> > > +	struct tpm_tis_spi_phy *phy = to_tpm_tis_spi_phy(data);
> > > +	struct spi_controller *ctlr = phy->spi_device->controller;
> > > +
> > > +	/*
> > > +	 * TPM flow control over SPI requires full duplex support.
> > > +	 * Send entire message to a half duplex controller to handle
> > > +	 * wait polling in controller.
> > > +	 * Set TPM HW flow control flag..
> > > +	 */
> > > +	if (ctlr->flags & SPI_CONTROLLER_HALF_DUPLEX) {
> > > +		phy->spi_device->mode |= SPI_TPM_HW_FLOW;
> 
> Shouldn't we check that this special flow is supported when the SPI
> device is bound to the tpm in the first place?
TPM device connected behind half duplex controller can only work
this way. So, no additional flag needed to check.
KY
> 
> Jason




[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux