On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote: > From: Selvam Sathappan Periakaruppan <quic_speriaka@xxxxxxxxxxx> > > IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that > platform. > > The code is based on downstream[1] Codeaurora kernel v5.4 (branch > win.linuxopenwrt.2.0). > > Split out the DBI registers access part from .init into .post_init. DBI > registers are only accessible after phy_power_on(). > > [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/ > > Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@xxxxxxxxxxxxxx> > Signed-off-by: Baruch Siach <baruch.siach@xxxxxxxxx> > --- > +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie) > +{ > + struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0; > + > + clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks); Assert reset as you do in the init error path? > +} > + > +static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie) > +{ > + struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0; > + struct device *dev = pcie->pci->dev; > + int ret; > + > + ret = reset_control_assert(res->rst); > + if (ret) { > + dev_err(dev, "reset assert failed (%d)\n", ret); > + return ret; > + } > + > + /* > + * Delay periods before and after reset deassert are working values > + * from downstream Codeaurora kernel > + */ > + usleep_range(2000, 2500); > + > + ret = reset_control_deassert(res->rst); > + if (ret) { > + dev_err(dev, "reset deassert failed (%d)\n", ret); > + return ret; > + } > + > + usleep_range(2000, 2500); > + > + ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks); > + if (ret) > + goto err_reset; > + > + return 0; > + > +err_reset: > + reset_control_assert(res->rst); > + > + return ret; > +} > + > +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie) > +{ > + struct dw_pcie *pci = pcie->pci; > + u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP); > + u32 val; > + int i; > + > + writel(SLV_ADDR_SPACE_SZ, > + pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE); > + > + val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); > + val &= ~BIT(0); > + writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); > + > + writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR); > + > + writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE); > + writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN, > + pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL); > + writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS > + | GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL, I noticed that some of this probably has been copied from from qcom_pcie_init_2_3_3(), but please move the | operator to the previous line. > + pci->dbi_base + GEN3_RELATED_OFF); > + > + writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS > + | SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS | Same here. > + AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS, > + pcie->parf + PCIE20_PARF_SYS_CTRL); > + > + writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH); > + > + dw_pcie_dbi_ro_wr_en(pci); > + writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP); > + > + val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP); > + val &= ~PCI_EXP_LNKCAP_ASPMS; > + writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP); > + > + writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset + > + PCI_EXP_DEVCTL2); > + > + for (i = 0; i < 256; i++) > + writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N > + + (4 * i)); And here for +, but you should probably just remove the line break (you can go up to 100 chars if it makes the code more readable). Please drop the 0x prefix too. > + > + return 0; > +} Johan
