Thanks Kent for the review comment. My responses inline.
On 7/1/21 7:21 AM, Kent Gibson wrote:
> On Fri, Jun 25, 2021 at 04:55:24PM -0700, Dipen Patel wrote:
>> Tegra194 device has multiple HTE instances also known as GTE
>> (Generic hardware Timestamping Engine) which can timestamp subset of
>> SoC lines/signals. This provider driver focuses on IRQ and GPIO lines
>> and exposes timestamping ability on those lines to the consumers
>> through HTE subsystem.
>>
>> Also, with this patch, added:
>> - documentation about this provider and its capabilities at
>> Documentation/hte.
>> - Compilation support in Makefile and Kconfig
>>
>> Signed-off-by: Dipen Patel <dipenp@xxxxxxxxxx>
>> ---
>> Documentation/hte/index.rst | 21 ++
>> Documentation/hte/tegra194-hte.rst | 65 ++++
>> Documentation/index.rst | 1 +
>> drivers/hte/Kconfig | 12 +
>> drivers/hte/Makefile | 1 +
>> drivers/hte/hte-tegra194.c | 554 +++++++++++++++++++++++++++++
>> 6 files changed, 654 insertions(+)
>> create mode 100644 Documentation/hte/index.rst
>> create mode 100644 Documentation/hte/tegra194-hte.rst
>> create mode 100644 drivers/hte/hte-tegra194.c
>>
>> diff --git a/Documentation/hte/index.rst b/Documentation/hte/index.rst
>> new file mode 100644
>> index 000000000000..f311ebec6b47
>> --- /dev/null
>> +++ b/Documentation/hte/index.rst
>> @@ -0,0 +1,21 @@
>> +.. SPDX-License-Identifier: GPL-2.0
>> +
>> +============================================
>> +The Linux Hardware Timestamping Engine (HTE)
>> +============================================
>> +
>> +The HTE Subsystem
>> +=================
>> +
>> +.. toctree::
>> + :maxdepth: 1
>> +
>> + hte
>> +
>> +HTE Tegra Provider
>> +==================
>> +
>> +.. toctree::
>> + :maxdepth: 1
>> +
>> + tegra194-hte
>> \ No newline at end of file
>> diff --git a/Documentation/hte/tegra194-hte.rst b/Documentation/hte/tegra194-hte.rst
>> new file mode 100644
>> index 000000000000..c23eaafcf080
>> --- /dev/null
>> +++ b/Documentation/hte/tegra194-hte.rst
>> @@ -0,0 +1,65 @@
>> +HTE Kernel provider driver
>> +==========================
>> +
>> +Description
>> +-----------
>> +The Nvidia tegra194 chip has many hardware timestamping engine (HTE) instances
>> +known as generic timestamping engine (GTE). This provider driver implements
>> +two GTE instances 1) GPIO GTE and 2) IRQ GTE. The both GTEs instances get the
>> +timestamp from the system counter TSC which has 31.25MHz clock rate, and the
>> +driver converts clock tick rate to nano seconds before storing it as timestamp
>> +value.
>> +
>> +GPIO GTE
>> +--------
>> +
>> +This GTE instance help timestamps GPIO in real time, for that to happen GPIO
>> +needs to be configured as input and IRQ needs to ba enabled as well. The only
>> +always on (AON) gpio controller instance supports timestamping GPIOs in
>> +realtime and it has 39 GPIO lines. There is also a dependency on AON GPIO
>> +controller as it requires very specific bits to be set in GPIO config register.
>> +It in a way creates cyclic dependency between GTE and GPIO controller. The GTE
>> +GPIO functionality is accessed from the GPIOLIB. It can support both the in
>> +kernel and userspace consumers. In the later case, requests go through GPIOLIB
>> +CDEV framework. The below APIs are added in GPIOLIB framework to access HTE
>> +subsystem and GPIO GTE for in kernel consumers.
>> +
>> +.. c:function:: int gpiod_hw_timestamp_control( struct gpio_desc *desc, bool enable )
>> +
>> + To enable HTE on given GPIO line.
>> +
>> +.. c:function:: u64 gpiod_get_hw_timestamp( struct gpio_desc *desc, bool block )
>> +
>> + To retrieve hardwre timestamp in nano seconds.
>> +
>> +.. c:function:: bool gpiod_is_hw_timestamp_enabled( const struct gpio_desc *desc )
>> +
>> + To query if HTE is enabled on the given GPIO.
>> +
>> +There is hte-tegra194-gpio-test.c, located in ``drivers/hte/`` directory, test
>> +driver which demonstrates above APIs for the Jetson AGX platform. For userspace
>> +consumers, GPIO_V2_LINE_FLAG_EVENT_CLOCK_HARDWARE flag must be specifed during
>> +IOCTL calls, refer ``tools/gpio/gpio-event-mon.c``, which returns the timestamp
>> +in nano second.
>> +
> <snip>
>
>> +
>> +static void tegra_hte_read_fifo(struct tegra_hte_soc *gs)
>> +{
>> + u32 tsh, tsl, src, pv, cv, acv, slice, bit_index, line_id;
>> + u64 tsc;
>> + int dir;
>> + struct hte_ts_data el;
>> +
>> + while ((tegra_hte_readl(gs, HTE_TESTATUS) >>
>> + HTE_TESTATUS_OCCUPANCY_SHIFT) &
>> + HTE_TESTATUS_OCCUPANCY_MASK) {
>> + tsh = tegra_hte_readl(gs, HTE_TETSCH);
>> + tsl = tegra_hte_readl(gs, HTE_TETSCL);
>> + tsc = (((u64)tsh << 32) | tsl);
>> +
>> + src = tegra_hte_readl(gs, HTE_TESRC);
>> + slice = (src >> HTE_TESRC_SLICE_SHIFT) &
>> + HTE_TESRC_SLICE_DEFAULT_MASK;
>> +
>> + pv = tegra_hte_readl(gs, HTE_TEPCV);
>> + cv = tegra_hte_readl(gs, HTE_TECCV);
>> + acv = pv ^ cv;
>> + while (acv) {
>> + bit_index = __builtin_ctz(acv);
>> + if ((pv >> bit_index) & BIT(0))
>> + dir = HTE_EVENT_RISING_EDGE;
>> + else
>> + dir = HTE_EVENT_FALLING_EDGE;
>> +
>> + line_id = bit_index + (slice << 5);
>> + el.dir = dir;
>> + el.tsc = tsc << HTE_TS_NS_SHIFT;
>> + hte_push_ts_ns_atomic(gs->chip, line_id, &el,
>> + sizeof(el));
>> + acv &= ~BIT(bit_index);
>> + }
>> + tegra_hte_writel(gs, HTE_TECMD, HTE_TECMD_CMD_POP);
>> + }
>> +}
> What happens when the hte_push_ts_ns_atomic() fails?
> The timestamp will be quietly dropped?
> What happens when the interrupt corresponding to that dropped timestamp
> asks for it? The irq handler thread will block until it can get a
> timestamp from the subsequent interrupt?
Two things happen, 1) at the push, HTE core increments seq counter
2) If the consumer has provided callback, it will either call that callback
with HTE_TS_DROPPED or HTE_TS_AVAIL. The seq counter gives indirect
view of dropped ts. However, I see the problem with the consumers not
providing callback, in that case, push_ts* API just wakes up process without
indicating why (assuming notify variable is true or else there is a chance for
the thread to block forever). One easy approach I can think of for now is to
make callback mandatory (which is optional right now), I will have to rethink
that scenario and will push corrected version next RFC version.
Thanks for pointing out.
>
> Which brings me back to the concern I have with the approach used in
> the hte/gpiolib integration - how do you guarantee that the timestamp
> returned by gpiod_get_hw_timestamp() corresponds to the irq interrupt
> being handled, particularly in the face of errors such as:
> - overflows of the timestamp FIFO in the chip
I currently do not have any indication mechanism as the providers
I am dealing with right now does not have overflow hardware detection
support. If the chip supports, it should be easy to integrate that feature.
I will provide some hook function or change in push_* API to accommodate
this in next version of RFC.
> - overflows of software FIFOs as here
HTE core records sequence counter as well it callsback the consumer with
HTE_TS_DROPPED.
> - lost interupts (if the hw generates interrupts faster than the CPU
> can service them)
For this, I have no idea unless hardware supports some sort of mechanism
to catch that. For the current providers, as soon as it detects changes on lines
it captures TS in its hw fifo. Its interrupt gets generated based on threshold
set in that hw fifo. This interrupt is different than the lines of actual device
that is why I said I have no idea how we can tackle that. Let me know if there
is any idea or reference of the codes which does tackle this.
Regarding HTE/GPIOLIB integration comment:
You are right, currently, I have only tsc field returned from struct hte_ts_data
to gpiolib. If I can extend that to return hte_ts_data structure which has seq
counter, which I believe can be used to track the overflow situation. The
dropped scenario can be easily tracked if gpiolib can be notified with above
mentioned DROP event through callback. If that is the case, is it ok to have
some sort of callback per gpio in gpiolib?
Any idea how I can integrate callback notification with gpiolib if you do not agree on
above callback suggestion?
> ?
>
> Cheers,
> Kent.
>
