Re: [RFC PATCH v6 09/10] media: tegra-video: Add CSI MIPI pads calibration

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



31.07.2020 19:29, Sowjanya Komatineni пишет:
> 
> On 7/31/20 9:14 AM, Dmitry Osipenko wrote:
>> 31.07.2020 18:46, Sowjanya Komatineni пишет:
>>> On 7/31/20 4:39 AM, Dmitry Osipenko wrote:
>>>> 31.07.2020 12:02, Sowjanya Komatineni пишет:
>>>> ...
>>>>> @@ -249,13 +249,47 @@ static int tegra_csi_enable_stream(struct
>>>>> v4l2_subdev *subdev)
>>>>>            return ret;
>>>>>        }
>>>>>    +    if (csi_chan->mipi) {
>>>>> +        ret = tegra_mipi_enable(csi_chan->mipi);
>>>>> +        if (ret < 0) {
>>>>> +            dev_err(csi->dev,
>>>>> +                "failed to enable MIPI pads: %d\n", ret);
>>>>> +            goto rpm_put;
>>>>> +        }
>>>>> +
>>>>> +        /*
>>>>> +         * CSI MIPI pads PULLUP, PULLDN and TERM impedances need to
>>>>> +         * be calibrated after power on.
>>>>> +         * So, trigger the calibration start here and results will
>>>>> +         * be latched and applied to the pads when link is in LP11
>>>>> +         * state during start of sensor streaming.
>>>>> +         */
>>>>> +        ret = tegra_mipi_start_calibration(csi_chan->mipi);
>>>>> +        if (ret < 0) {
>>>>> +            dev_err(csi->dev,
>>>>> +                "failed to start MIPI calibration: %d\n", ret);
>>>>> +            goto disable_mipi;
>>>>> +        }
>>>> What would happen if CSI stream is enabled and then immediately
>>>> disabled
>>>> without enabling camera sensor?
>>> Nothing will happen as during stream enable csi receiver is kept ready.
>>>
>>> But actual capture will not happen during that point.
>> Could you please show how the full call chain looks like? It's not clear
>> to me what keeps CSI stream "ready".
> 
> VI is the main video input (video device) and on streaming it starts
> stream of CSI subdev prior to stream of Sensor.
> 
> HW path, sensor stream (CSI TX) -> CSI stream (RX)
> 
> During CSI stream on, CSI PHY receiver is enabled to start receiving the
> data but internally capture assembled to active state will happen only
> when Tegra VI single shot is issues where VI thru pixel parser gets
> captures data into the memory

Alright, I see now.

Will be great if you could change this hunk:

{
  ret = v4l2_subdev_call(src_subdev, video, s_stream, true);
  if (ret < 0 && ret != -ENOIOCTLCMD) {
    tegra_mipi_cancel_calibration(csi_chan->mipi);
    v4l2_subdev_call(csi_subdev, video, s_stream, false);
    return ret;
  }
}

to look like this:

{
  err = v4l2_subdev_call(src_subdev, video, s_stream, true);
  if (err < 0 && err != -ENOIOCTLCMD)
    goto err_disable_csi_stream;
...
  return 0;

err_disable_csi_stream:
  tegra_mipi_cancel_calibration(csi_chan->mipi);

  v4l2_subdev_call(csi_subdev, video, s_stream, false);

  return err;
}


It should make code a bit easier to read and follow.

Otherwise this patch looks good to me, thanks.



[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux