Re: [PATCH v6 10/14] memory: tegra: Add EMC scaling sequence code for Tegra210

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Apr 10, 2020 at 05:18:51PM +0300, Dmitry Osipenko wrote:
> 09.04.2020 20:52, Thierry Reding пишет:
> ...
> > +static void tegra210_emc_r21021_set_clock(struct tegra210_emc *emc, u32 clksrc)
> > +{
> > +	/*
> > +	 * This is the timing table for the source frequency. It does _not_
> > +	 * necessarily correspond to the actual timing values in the EMC at the
> > +	 * moment. If the boot BCT differs from the table then this can happen.
> > +	 * However, we need it for accessing the dram_timings (which are not
> > +	 * really registers) array for the current frequency.
> > +	 */
> > +	u32 tmp, cya_allow_ref_cc = 0, ref_b4_sref_en = 0, cya_issue_pc_ref = 0;
> > +	struct tegra210_emc_timing *fake, *last = emc->last, *next = emc->next;
> > +	u32 bg_regulator_switch_complete_wait_clks, bg_regulator_mode_change;
> > +	u32 opt_zcal_en_cc, opt_do_sw_qrst = 1, opt_dvfs_mode, opt_dll_mode;
> > +	u32 emc_zcal_wait_cnt_old, emc_zcal_wait_cnt_new, emc_dbg_active;
> > +	u32 opt_cc_short_zcal = 1, opt_short_zcal = 1, opt_war_200024907;
> > +	u32 tRTM, RP_war, R2P_war, TRPab_war, deltaTWATM, W2P_war, tRPST;
> > +	u32 adel = 0, compensate_trimmer_applicable = 0, mrw_req, value;
> > +	unsigned long next_timing_rate_mhz = next->rate / 1000, delay;
> > +	u32 tZQCAL_lpddr4 = 1000000, zq_wait_long, shared_zq_resistor;
> > +	s32 zq_latch_dvfs_wait_time, tZQCAL_lpddr4_fc_adj, nRTP;
> > +	u32 tFC_lpddr4 = 1000 * next->dram_timings[T_FC_LPDDR4];
> > +	u32 emc_auto_cal_config, auto_cal_en, mr13_catr_enable;
> > +	u32 zq_op, zcal_wait_time_clocks, zcal_wait_time_ps;
> > +	u32 emc_cfg, emc_sel_dpd_ctrl, emc_zcal_interval;
> > +	int next_push, next_dq_e_ivref, next_dqs_e_ivref;
> > +	u32 mr13_flip_fspwr, mr13_flip_fspop, is_lpddr3;
> > +	u32 enable_bglp_regulator, enable_bg_regulator;
> > +	u32 emc_dbg_o, emc_cfg_pipe_clk_o, emc_pin_o;
> > +	u32 ramp_up_wait = 0, ramp_down_wait = 0;
> > +	u32 save_restore_clkstop_pd = 1, dll_out;
> > +	u32 ref_delay_mult, ref_delay, dram_type;
> > +	static u32 fsp_for_next_freq;
> > +	/* In picoseconds. */
> > +	u32 source_clock_period, destination_clock_period;
> > +	u32 zqcal_before_cc_cutoff = 2400;
> > +	unsigned int i;
> 
> What about to try to replace this massive egyptian construction with a
> single "u32 val;" ?

I actually tried that after condensing what this used to look like into
the above. The result was a huge failure because some of these temporary
values end up being reused, so I ended up writing bogus values into some
of these registers.

> > +	emc_readl(emc, EMC_CFG);
> > +	emc_auto_cal_config = emc_readl(emc, EMC_AUTO_CAL_CONFIG);
> 
> And remove all the "dummy" variable assigns in the code?
> 
> ...
> > emc_auto_cal_config = next->emc_auto_cal_config;
> ...> +	emc_zcal_interval = 0;
> 
> And replace all "constant" variables with a raw value in place in the code?

Okay, I'll give this another try, hopefully this time I won't run into
the same problems as earlier.

Thierry

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux