On 1/7/20 3:28 PM, Dmitry Osipenko wrote:
08.01.2020 02:24, Sowjanya Komatineni пишет:
On 1/7/20 3:01 PM, Dmitry Osipenko wrote:
Hello Sowjanya,
07.01.2020 07:13, Sowjanya Komatineni пишет:
This patch series moves Tegra PMC clocks from clock driver to pmc driver
along with the device trees changes and audio driver which uses one of
the pmc clock for audio mclk.
Tegra PMC has clk_out_1, clk_out_2, clk_out_3 and blink controls which
are currently registered by Tegra clock driver using clk_regiser_mux and
clk_register_gate which performs direct Tegra PMC register access.
When Tegra PMC is in secure mode, any access from non-secure world will
not go through.
This patch series adds these Tegra PMC clocks and blink controls to
Tegra
PMC driver with PMC as clock provider and removes them from Tegra clock
driver.
PMC clock clk_out_1 is dedicated for audio mclk from Tegra30 thru
Tegra210
and clock driver does inital parent configuration for it and enables
them.
But this clock should be taken care by audio driver as there is no need
to have this clock pre enabled.
So, this series also includes patch that updates ASoC driver to take
care of parent configuration for mclk if device tree don't specify
initial parent configuration using assigned-clock-parents and controls
audio mclk enable/disable during ASoC machine startup and shutdown.
DTs are also updated to use clk_out_1 as audio mclk rather than extern1.
This series also includes a patch for mclk fallback to extern1 when
retrieving mclk fails to have this backward compatible of new DT with
old kernels.
[v6]: Changes between v5 and v6 are
- v5 feedback
- Added ASoC machine startup and shutdown callbacks to control audio
mclk enable/disable and removed default mclk enable from clock
driver.
- Updated tegra_asoc_utils_set_rate to disable mclk only during PLLA
rate change and removed disabling PLLA as its already taken
care by
pll clock driver.
- Removed tegra_asoc_utils_set_rate call from utils_init as set_rate
is set during machine hw_params and during utils_init mclk is
already in disabled state and this causes warning during mclk
disable
in utils_set_rate.
[v5]: Changes between v4 and v5 are
- v4 feedback
- updated dt-binding pmc YAML schema with more description on power
gate nodes and pad configuration state nodes.
- update tegra_asoc_utils_set_rate to disable audio mclk only if
its in enable state.
[v4]: Changes between v3 and v4 are
- v3 Feedback
- Updated clocks clk_m_div2 and clk_m_div4 as osc_div2 and osc_div4.
Tegra don't have clk_m_div2, clk_m_div4 and they should actually
be osc_div2 and osc_div4 clocks from osc pads.
- Fixed PMC clock parents to use osc, osc_div2, osc_div4.
- Register each PMC clock as single clock rather than separate
mux and gate clocks.
- Update ASoC utils to use resource managed APIs rather than
using clk_get and clk_put.
- Updated device tree and ASoC driver to use clk_out_1 instead of
clk_out_1_mux as PMC clocks are registered as single clock.
- Update clock driver init_table to not enable audio related clocks
as ASoC utils will do audio clock enables.
[v3]: Changes between v2 and v3 are
- Removes set parent of clk_out_1_mux to extern1 and enabling
extern1 from the clock driver.
- Doesn't enable clk_out_1 and blink by default in pmc driver
- Updates ASoC driver to take care of audio mclk parent
configuration incase if device tree don't specify assigned
clock parent properties and enables mclk using both clk_out_1
and extern1.
- updates all device trees using extern1 as mclk in sound node
to use clk_out_1 from pmc.
- patch for YAML format pmc dt-binding
- Includes v2 feedback
[v2]: Changes between v1 and v2 are
- v2 includes patches for adding clk_out_1, clk_out_2, clk_out_3,
blink controls to Tegra PMC driver and removing clk-tegra-pmc.
- feedback related to pmc clocks in Tegra PMC driver from v1
- Removed patches for WB0 PLLM overrides and PLLE IDDQ PMC
programming
by the clock driver using helper functions from Tegra PMC.
Note:
To use helper functions from PMC driver, PMC early init need to
happen prior to using helper functions and these helper
functions are
for PLLM Override and PLLE IDDQ programming in PMC during
PLLM/PLLE
clock registration which happen in clock_init prior to Tegra PMC
probe.
Moving PLLM/PLLE clocks registration to happen after Tegra PMC
impacts other clocks EMC, MC and corresponding tegra_emc_init and
tegra_mc_init.
This implementation of configuring PMC registers thru helper
functions in clock driver needs proper changes across PMC, Clock,
EMC and MC inits to have it work across all Tegra platforms.
Currently PLLM Override is not enabled in the bootloader so proper
patches for this fix will be taken care separately.
[v1]: v1 includes patches for below fixes.
- adding clk_out_1, clk_out_2, clk_out_3, blink controls to Tegra
PMC
driver and removing clk-tegra-pmc.
- updated clock provider from tegra_car to pmc in the device tree
tegra210-smaug.dts that uses clk_out_2.
- Added helper functions in PMC driver for WB0 PLLM overrides and
PLLE
IDDQ programming to use by clock driver and updated clock
driver to
use these helper functions and removed direct PMC access from
clock
driver and all pmc base address references in clock driver.
Sowjanya Komatineni (19):
dt-bindings: clock: tegra: Change CLK_M_DIV to OSC_DIV clocks
clk: tegra: Change CLK_M_DIV clocks to OSC_DIV clocks
clk: tegra: Fix Tegra PMC clock out parents
dt-bindings: tegra: Convert Tegra PMC bindings to YAML
dt-bindings: soc: tegra-pmc: Add Tegra PMC clock bindings
soc: tegra: Add Tegra PMC clocks registration into PMC driver
dt-bindings: soc: tegra-pmc: Add id for Tegra PMC 32KHz blink clock
soc: tegra: Add support for 32KHz blink clock
clk: tegra: Remove tegra_pmc_clk_init along with clk ids
dt-bindings: clock: tegra: Remove pmc clock ids from clock
dt-bindings
ASoC: tegra: Use device managed resource APIs to get the clock
ASoC: tegra: Add audio mclk configuration
ASoC: tegra: Add fallback implementation for audio mclk
clk: tegra: Remove audio related clock enables from init_table
ARM: dts: tegra: Add clock-cells property to pmc
arm64: tegra: Add clock-cells property to Tegra PMC node
ARM: tegra: Update sound node clocks in device tree
arm64: tegra: smaug: Change clk_out_2 provider to pmc
ASoC: nau8825: change Tegra clk_out_2 provider from tegra_car to pmc
.../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 300
-----------------
.../bindings/arm/tegra/nvidia,tegra20-pmc.yaml | 354
+++++++++++++++++++++
.../devicetree/bindings/sound/nau8825.txt | 2 +-
arch/arm/boot/dts/tegra114-dalmore.dts | 8 +-
arch/arm/boot/dts/tegra114.dtsi | 4 +-
arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi | 8 +-
arch/arm/boot/dts/tegra124-apalis.dtsi | 8 +-
arch/arm/boot/dts/tegra124-jetson-tk1.dts | 8 +-
arch/arm/boot/dts/tegra124-nyan.dtsi | 8 +-
arch/arm/boot/dts/tegra124-venice2.dts | 8 +-
arch/arm/boot/dts/tegra124.dtsi | 4 +-
arch/arm/boot/dts/tegra20.dtsi | 4 +-
arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi | 8 +-
arch/arm/boot/dts/tegra30-apalis.dtsi | 8 +-
arch/arm/boot/dts/tegra30-beaver.dts | 8 +-
arch/arm/boot/dts/tegra30-cardhu.dtsi | 8 +-
arch/arm/boot/dts/tegra30-colibri.dtsi | 8 +-
arch/arm/boot/dts/tegra30.dtsi | 4 +-
arch/arm64/boot/dts/nvidia/tegra132.dtsi | 4 +-
arch/arm64/boot/dts/nvidia/tegra210-smaug.dts | 2 +-
arch/arm64/boot/dts/nvidia/tegra210.dtsi | 6 +-
drivers/clk/tegra/Makefile | 1 -
drivers/clk/tegra/clk-id.h | 11 +-
drivers/clk/tegra/clk-tegra-fixed.c | 32 +-
drivers/clk/tegra/clk-tegra-pmc.c | 122 -------
drivers/clk/tegra/clk-tegra114.c | 41 +--
drivers/clk/tegra/clk-tegra124.c | 46 +--
drivers/clk/tegra/clk-tegra20.c | 9 +-
drivers/clk/tegra/clk-tegra210.c | 30 +-
drivers/clk/tegra/clk-tegra30.c | 31 +-
drivers/clk/tegra/clk.h | 1 -
drivers/soc/tegra/pmc.c | 352
++++++++++++++++++++
include/dt-bindings/clock/tegra114-car.h | 18 +-
include/dt-bindings/clock/tegra124-car-common.h | 18 +-
include/dt-bindings/clock/tegra20-car.h | 2 +-
include/dt-bindings/clock/tegra210-car.h | 18 +-
include/dt-bindings/clock/tegra30-car.h | 18 +-
include/dt-bindings/soc/tegra-pmc.h | 16 +
sound/soc/tegra/tegra_alc5632.c | 28 +-
sound/soc/tegra/tegra_asoc_utils.c | 125 ++++----
sound/soc/tegra/tegra_asoc_utils.h | 3 +-
sound/soc/tegra/tegra_max98090.c | 43 ++-
sound/soc/tegra/tegra_rt5640.c | 43 ++-
sound/soc/tegra/tegra_rt5677.c | 28 +-
sound/soc/tegra/tegra_sgtl5000.c | 28 +-
sound/soc/tegra/tegra_wm8753.c | 43 ++-
sound/soc/tegra/tegra_wm8903.c | 43 ++-
sound/soc/tegra/tegra_wm9712.c | 8 +-
sound/soc/tegra/trimslice.c | 39 ++-
49 files changed, 1192 insertions(+), 777 deletions(-)
delete mode 100644
Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
create mode 100644
Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml
delete mode 100644 drivers/clk/tegra/clk-tegra-pmc.c
create mode 100644 include/dt-bindings/soc/tegra-pmc.h
I briefly looked through the patches and tested them in all possible
configurations. For now everything looks and works well.
You could add this to all patches:
Tested-by: Dmitry Osipenko <digetx@xxxxxxxxx>
Reviewed-by: Dmitry Osipenko <digetx@xxxxxxxxx>
Thanks Dmitry
Actually, it will be more accurate if you will add my t-b only to the
T20/30 patches. I only looked through the T114+ patches without testing
them, thanks.
Most of patches has changes to t20 through t210.
Just to be clear, do you meant to add Tested-by to patches 6, 8, 11, 12,
13 and Reviewed-by tag to all patches?
