This patch adds YAML schema for Tegra PMC bindings. Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx> --- .../bindings/arm/tegra/nvidia,tegra20-pmc.yaml | 291 +++++++++++++++++++++ 1 file changed, 291 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml new file mode 100644 index 000000000000..ab614f1be177 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml @@ -0,0 +1,291 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/tegra/nvidia,tegra20-pmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Tegra Power Management Controller (PMC) + +maintainers: + - Thierry Reding <thierry.reding@xxxxxxxxx> + - Jonathan Hunter <jonathanh@xxxxxxxxxx> + +properties: + compatible: + oneOf: + - items: + - const: nvidia,tegra20-pmc + - const: nvidia,tegra20-pmc + - const: nvidia,tegra30-pmc + - const: nvidia,tegra114-pmc + - const: nvidia,tegra124-pmc + - const: nvidia,tegra210-pmc + + reg: + maxItems: 1 + + clock-names: + items: + - const: pclk, clk32k_in + description: + pclk is the Tegra clock of that name and clk32k_in is 32KHz clock + input to Tegra. + + clocks: + maxItems: 2 + + '#clock-cells': + const: 1 + description: + Tegra PMC has clk_out_1, clk_out_2, and clk_out_3. + Consumer of PMC clock should specify the desired clock by having + the clock ID in its "clocks" phandle cell with pmc clock provider. + See include/dt-bindings/soc/tegra-pmc.h for the list of Tegra PMC + clock IDs. + + nvidia,invert-interrupt: + $ref: /schemas/types.yaml#/definitions/flag + description: Inverts the PMU interrupt signal. + The PMU is an external Power Management Unit, whose interrupt output + signal is fed into the PMC. This signal is optionally inverted, and + then fed into the ARM GIC. The PMC is not involved in the detection + or handling of this interrupt signal, merely its inversion. + + nvidia,core-power-req-active-high: + $ref: /schemas/types.yaml#/definitions/flag + description: Core power request active-high. + + nvidia,sys-clock-req-active-high: + $ref: /schemas/types.yaml#/definitions/flag + description: System clock request active-high. + + nvidia,combined-power-req: + $ref: /schemas/types.yaml#/definitions/flag + description: combined power request for CPU and Core. + + nvidia,cpu-pwr-good-en: + $ref: /schemas/types.yaml#/definitions/flag + description: + CPU power good signal from external PMIC to PMC is enabled. + + nvidia,suspend-mode: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0, 1, 2] + description: + The suspend mode that the platform should use. + Mode 0 is for LP0, CPU + Core voltage off and DRAM in self-refresh + Mode 1 is for LP1, CPU voltage off and DRAM in self-refresh + Mode 2 is for LP2, CPU voltage off + + nvidia,cpu-pwr-good-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: CPU power good time in uSec. + + nvidia,cpu-pwr-off-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: CPU power off time in uSec. + + nvidia,core-pwr-good-time: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + <Oscillator-stable-time Power-stable-time> + Core power good time in uSec. + + nvidia,core-pwr-off-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Core power off time in uSec. + + nvidia,lp0-vec: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + <start length> Starting address and length of LP0 vector. + The LP0 vector contains the warm boot code that is executed + by AVP when resuming from the LP0 state. + The AVP (Audio-Video Processor) is an ARM7 processor and + always being the first boot processor when chip is power on + or resume from deep sleep mode. When the system is resumed + from the deep sleep mode, the warm boot code will restore + some PLLs, clocks and then brings up CPU0 for resuming the + system. + + i2c-thermtrip: + type: object + description: + On Tegra30, Tegra114 and Tegra124 if i2c-thermtrip subnode exists, + hardware-triggered thermal reset will be enabled. + + properties: + nvidia,i2c-controller-id: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + ID of I2C controller to send poweroff command to PMU. + Valid values are described in section 9.2.148 + "APBDEV_PMC_SCRATCH53_0" of the Tegra K1 Technical Reference + Manual. + + nvidia,bus-addr: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Bus address of the PMU on the I2C bus. + + nvidia,reg-addr: + $ref: /schemas/types.yaml#/definitions/uint32 + description: PMU I2C register address to issue poweroff command. + + nvidia,reg-data: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Poweroff command to write to PMU. + + nvidia,pinmux-id: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Pinmux used by the hardware when issuing Poweroff command. + Defaults to 0. Valid values are described in section 12.5.2 + "Pinmux Support" of the Tegra4 Technical Reference Manual. + + required: + - nvidia,i2c-controller-id + - nvidia,bus-addr + - nvidia,reg-addr + - nvidia,reg-data + + powergates: + type: object + description: + This node contains a hierarchy of power domain nodes, which should + match the powergates on the Tegra SoC. Each powergate node + represents a power-domain on the Tegra SoC that can be power-gated + by the Tegra PMC. + Hardware blocks belonging to a power domain should contain + "power-domains" property that is a phandle pointing to corresponding + powergate node. + Please refer to Tegra TRM for mode details on the powergate nodes to + use for each power-gate block inside Tegra. + + patternProperties: + "^[a-z0-9]+$": + if: + type: object + then: + patternProperties: + clocks: + description: + Must contain an entry for each clock required by the PMC + for controlling a power-gate. + See ../clocks/clock-bindings.txt document for more details. + + resets: + description: + Must contain an entry for each reset required by the PMC + for controlling a power-gate. + See ../reset/reset.txt for more details. + + '#power-domain-cells': + description: Must be 0. + + required: + - clocks + - resets + - '#power-domain-cells' + +patternProperties: + "^.*@[0-9a-f]+$": + type: object + + properties: + pins: + $ref: /schemas/types.yaml#/definitions/string + description: Must contain name of the pad(s) to be configured. + + low-power-enable: + $ref: /schemas/types.yaml#/definitions/flag + description: Configure the pad into power down mode. + + low-power-disable: + $ref: /schemas/types.yaml#/definitions/flag + description: Configure the pad into active mode. + + power-source: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or + TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages. + The values are defined in + include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h. + Power state can be configured on all Tegra124 and Tegra132 + pads. None of the Tegra124 or Tegra132 pads support signaling + voltage switching. + All of the listed Tegra210 pads except pex-cntrl support power + state configuration. Signaling voltage switching is supported + on below Tegra210 pads. + audio, audio-hv, cam, dbg, dmic, gpio, pex-cntrl, sdmmc1, + sdmmc3, spi, spi-hv, and uart. + + required: + - pins + +required: + - compatible + - reg + - clock-names + - clocks + - '#clock-cells' + +if: + properties: + nvidia,suspend-mode: + contains: + const: 2 + +then: + required: + - nvidia,cpu-pwr-good-time + - nvidia,cpu-pwr-off-time + - nvidia,core-pwr-good-time + - nvidia,core-pwr-off-time + +examples: + - | + #include <dt-bindings/soc/tegra-pmc.h> + + pmc: pmc@7000e400 { + compatible = "nvidia,tegra210-pmc"; + reg = <0x0 0x7000e400 0x0 0x400>; + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>; + clock-names = "pclk", "clk32k_in"; + #clock-cells = <1>; + + powergates { + pd_audio: aud { + clocks = <&tegra_car TEGRA210_CLK_APE>, + <&tegra_car TEGRA210_CLK_APB2APE>; + resets = <&tegra_car 198>; + #power-domain-cells = <0>; + }; + + pd_xusbss: xusba { + clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>; + resets = <&tegra_car TEGRA210_CLK_XUSB_SS>; + #power-domain-cells = <0>; + }; + }; + + sdmmc1_3v3: sdmmc1-3v3 { + pins = "sdmmc1"; + power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>; + }; + + sdmmc1_1v8: sdmmc1-1v8 { + pins = "sdmmc1"; + power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>; + }; + + nvidia,invert-interrupt; + nvidia,suspend-mode = <0>; + nvidia,cpu-pwr-good-time = <0>; + nvidia,cpu-pwr-off-time = <0>; + nvidia,core-pwr-good-time = <4587 3876>; + nvidia,core-pwr-off-time = <39065>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; + }; -- 2.7.4
