Re: [PATCH v2 00/11] Move PMC clocks into Tegra PMC driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 11/28/19 5:06 AM, Dmitry Osipenko wrote:
28.11.2019 00:38, Sowjanya Komatineni пишет:
On 11/27/19 9:02 AM, Sowjanya Komatineni wrote:
On 11/27/19 6:31 AM, Dmitry Osipenko wrote:
27.11.2019 07:59, Sowjanya Komatineni пишет:
Tegra PMC has clk_out_1, clk_out_2, clk_out_3 and blink controls which
are currently registered by Tegra clock driver using clk_regiser_mux
and
clk_register_gate which performs direct Tegra PMC register access.

When Tegra PMC is in secure mode, any access from non-secure world will
not go through.

This patch series adds these Tegra PMC clocks and blink controls to
Tegra
PMC driver with PMC as clock provider and removed them from Tegra clock
driver. This also adds PMC specific clock id's to use in device tree
and
removed clock ids of PMC clock from Tegra clock driver.

This series also includes patch to update clock provider from tegra_car
to pmc in the device tree tegra210-smaug.dts that uses clk_out_2
from PMC.

[v2]:    Changes between v1 and v2 are
     - v2 includes patches for adding clk_out_1, clk_out_2, clk_out_3,
       blink controls to Tegra PMC driver and removing clk-tegra-pmc.
     - feedback related to pmc clocks in Tegra PMC driver from v1
     - Removed patches for WB0 PLLM overrides and PLLE IDDQ PMC
programming
       by the clock driver using helper functions from Tegra PMC.

         Note:
       To use helper functions from PMC driver, PMC early init need to
       happen prior to using helper functions and these helper
functions are
       for PLLM Override and PLLE IDDQ programming in PMC during
PLLM/PLLE
       clock registration which happen in clock_init prior to Tegra PMC
       probe.
       Moving PLLM/PLLE clocks registration to happen after Tegra PMC
       impacts other clocks EMC, MC and corresponding tegra_emc_init and
       tegra_mc_init.
       This implementation of configuring PMC registers thru helper
       functions in clock driver needs proper changes across PMC, Clock,
       EMC and MC inits to have it work across all Tegra platforms.

       Currently PLLM Override is not enabled in the bootloader so
proper
       patches for this fix will be taken care separately.
Hello Sowjanya,

Could you please clarify what do you mean by "PLLM Override not enabled
in bootloader"?

There is T124 Nyan Big Chromebook which is supported in upstream kernel,
it has PLLM Override set by bootloader. I also have T30 Nexus 7 tablet
which has the PLLM Override set by bootloader as well. It's not clear to
me whether this patch series is supposed to break these devices. If the
breakage is the case here, then I'm afraid you can't postpone supporting
the PLLM Override and a full-featured implementation is needed.
Hi Dmitry,

Secure boot currently is enabled only on Tegra210 and Tegra210
bootloader doesn't enable PLLM override.

So PLLM override/PLLE IDDQ being in clock driver currently will not
break on any of existing Tegra platforms.

I briefly tried to test this series on T30 and this time it doesn't hang
on boot, but somehow WiFi MMC card detection is broken. AFAIK, the WiFi
chip uses the Blink clock source and the clock should be enabled by the
MMC core because this is how DT part looks like:

brcm_wifi_pwrseq: wifi-pwrseq {
     compatible = "mmc-pwrseq-simple";
     clocks = <&pmc TEGRA_PMC_CLK_BLINK>;
     clock-names = "ext_clock";
     reset-gpios =  <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
     post-power-on-delay-ms = <300>;
     power-off-delay-us = <300>;
};

BTW, I  tried this series on a T20 device which also uses the Blink
clock for WiFi card and it works. So looks like this patchset has some
problem in regards to the T30 PMC clocks implementation.

[snip]
Blink init state is set to true for both Tegra20 and Tegra30 and all
go through the same blink programming sequence.

Will try to add more debug messages to dump registers and will test
blink through device tree on T30 and will get back...


define value for BLINK uses BIT macro instead of just position. Will fix
this in v3.
Thanks, will try v3 once it will be ready.

I took a look through the T20 board's schematics and seems it doesn't
use the Blink clock for the WiFi, instead it uses 32k source directly
from PMU. While T30 board schematics tells that  32k comes out from the
Tegra chip.

BTW, I'm curious what's the reason for having Blink clock always-ON on
T20/30, any insights? Looks like it's just some relic from old clk
driver and it should be safe to drop the always-ON.

T30 cardhu uses 32K from Tegra to WIFI but its only needed to be on during WIFI power up sequence and not required to be on during boot.

I had it enabled as existing clock driver enables it default and dont want to break things if it was left ON intentionally.

Peter/Thierry, Any reason 32K from Blink is enabled to be ON during clock init for T20/T30 in clock-tegra-pmc driver?

Based on the design T30 uses this for WIFI and WIFI driver should be handling this clock enable/disable during power up/down sequence,

so we don't have to enable it default during boot right?





[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux