On 12-07-19, 16:40, Sameer Pujar wrote:
> >From Tegra186 onwards OUTSTANDING_REQUESTS field is added in channel
^^
please remove the leading char from the para
> configuration register(bits 7:4) which defines the maximum number of reads
> from the source and writes to the destination that may be outstanding at
> any given point of time. This field must be programmed with a value
> between 1 and 8. A value of 0 will prevent any transfers from happening.
>
> Thus added 'ch_pending_req' member in chip data structure and the same is
> populated with maximum allowed pending requests. Since the field is not
> applicable to Tegra210, mentioned bit fields are unused and hence the
> member is initialized with 0. For Tegra186, by default program this field
> with the maximum permitted value of 8.
>
> Fixes: 433de642a76c ("dmaengine: tegra210-adma: add support for Tegra186/Tegra194")
Should this be tagged stable? Also some reviews from Tegra folks would
be great
>
> Signed-off-by: Sameer Pujar <spujar@xxxxxxxxxx>
> ---
> drivers/dma/tegra210-adma.c | 7 +++++++
> 1 file changed, 7 insertions(+)
>
> diff --git a/drivers/dma/tegra210-adma.c b/drivers/dma/tegra210-adma.c
> index 2805853..5ab4e3a9 100644
> --- a/drivers/dma/tegra210-adma.c
> +++ b/drivers/dma/tegra210-adma.c
> @@ -74,6 +74,8 @@
> TEGRA186_ADMA_CH_FIFO_CTRL_TXSIZE(3) | \
> TEGRA186_ADMA_CH_FIFO_CTRL_RXSIZE(3))
>
> +#define TEGRA186_DMA_MAX_PENDING_REQS 8
> +
> #define ADMA_CH_REG_FIELD_VAL(val, mask, shift) (((val) & mask) << shift)
>
> struct tegra_adma;
> @@ -85,6 +87,7 @@ struct tegra_adma;
> * @ch_req_tx_shift: Register offset for AHUB transmit channel select.
> * @ch_req_rx_shift: Register offset for AHUB receive channel select.
> * @ch_base_offset: Register offset of DMA channel registers.
> + * @ch_pending_req: Outstaning DMA requests for a channel.
> * @ch_fifo_ctrl: Default value for channel FIFO CTRL register.
> * @ch_req_mask: Mask for Tx or Rx channel select.
> * @ch_req_max: Maximum number of Tx or Rx channels available.
> @@ -98,6 +101,7 @@ struct tegra_adma_chip_data {
> unsigned int ch_req_tx_shift;
> unsigned int ch_req_rx_shift;
> unsigned int ch_base_offset;
> + unsigned int ch_pending_req;
> unsigned int ch_fifo_ctrl;
> unsigned int ch_req_mask;
> unsigned int ch_req_max;
> @@ -602,6 +606,7 @@ static int tegra_adma_set_xfer_params(struct tegra_adma_chan *tdc,
> ADMA_CH_CTRL_FLOWCTRL_EN;
> ch_regs->config |= cdata->adma_get_burst_config(burst_size);
> ch_regs->config |= ADMA_CH_CONFIG_WEIGHT_FOR_WRR(1);
> + ch_regs->config |= cdata->ch_pending_req;
so for tegra186 this will be 0, which per above would prevent any
transfers?? What did i miss
> ch_regs->fifo_ctrl = cdata->ch_fifo_ctrl;
> ch_regs->tc = desc->period_len & ADMA_CH_TC_COUNT_MASK;
>
> @@ -786,6 +791,7 @@ static const struct tegra_adma_chip_data tegra210_chip_data = {
> .ch_req_tx_shift = 28,
> .ch_req_rx_shift = 24,
> .ch_base_offset = 0,
> + .ch_pending_req = 0,
> .ch_fifo_ctrl = TEGRA210_FIFO_CTRL_DEFAULT,
> .ch_req_mask = 0xf,
> .ch_req_max = 10,
> @@ -800,6 +806,7 @@ static const struct tegra_adma_chip_data tegra186_chip_data = {
> .ch_req_tx_shift = 27,
> .ch_req_rx_shift = 22,
> .ch_base_offset = 0x10000,
> + .ch_pending_req = (TEGRA186_DMA_MAX_PENDING_REQS << 4),
> .ch_fifo_ctrl = TEGRA186_FIFO_CTRL_DEFAULT,
> .ch_req_mask = 0x1f,
> .ch_req_max = 20,
> --
> 2.7.4
--
~Vinod
