Re: [Patch V3 4/8] dt-bindings: usb: Add NVIDIA Tegra XUSB device mode controller binding

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 14-06-2019 03:02, Rob Herring wrote:
> On Thu, May 16, 2019 at 12:09:28PM +0530, Nagarjuna Kristam wrote:
>> Add device-tree binding documentation for the XUSB device mode controller
>> present on Tegra210 SoC. This controller supports the USB 3.0
>> specification.
>>
>> Signed-off-by: Nagarjuna Kristam <nkristam@xxxxxxxxxx>
>> ---
>>  .../devicetree/bindings/usb/nvidia,tegra-xudc.txt  | 101 +++++++++++++++++++++
>>  1 file changed, 101 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
>> new file mode 100644
>> index 0000000..d78b436
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
>> @@ -0,0 +1,101 @@
>> +Device tree binding for NVIDIA Tegra XUSB device mode controller (XUDC)
>> +=======================================================================
>> +
>> +The Tegra XUDC controller supports both USB 2.0 HighSpeed/FullSpeed and
>> +USB 3.0 SuperSpeed protocols.
>> +
>> +Required properties:
>> +--------------------
>> +- compatible: For Tegra210, must contain "nvidia,tegra210-xudc".
>> +- reg: Must contain the base and length of the XUSB device registers, XUSB device
>> +  PCI Config registers and XUSB device controller registers.
>> +- interrupts: Must contain the XUSB device interrupt.
>> +- clocks: Must contain an entry for all clocks used.
>> +  See ../clock/clock-bindings.txt for details.
>> +- clock-names: Must include the following entries:
>> +   - dev: Clock to enable core XUSB dev clock.
>> +   - ss: Clock to enable XUSB super speed clock.
>> +   - ss_src: Clock to enable XUSB super speed dev clock.
>> +   - hs_src: Clock to enable XUSB high Speed dev clock.
>> +   - fs_src: Clock to enable XUSB full Speed dev clock.
>> +- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to
>> +  configure the USB pads used by the XUDC controller.
>> +- power-domains: A list of PM domain specifiers that reference each power-domain
>> +  used by the XUSB device mode controller. This list must comprise of a specifier
>> +  for the XUSBA and XUSBB power-domains. See ../power/power_domain.txt and
>> +  ../arm/tegra/nvidia,tegra20-pmc.txt for details.
>> +- power-domain-names: A list of names that represent each of the specifiers in
>> +  the 'power-domains' property. Must include 'ss' and 'dev'.
>> +
>> +For Tegra210:
>> +- avddio-usb-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V.
> 
> Wouldn't an analog supply belong in the phy node?
> 

This is USB controller power supply and hence added it part of controller driver node.
Will correct documentation accordingly.

>> +- hvdd-usb-supply: USB controller power supply. Must supply 3.3 V.
>> +
>> +- phys: Must contain an entry for each entry in phy-names.
>> +  See ../phy/phy-bindings.txt for details.
>> +- phy-names: Should include an entry for each PHY used by the controller.
>> +  Names must be "usb2", and "usb3" if support SuperSpeed device mode.
>> +  - "usb3" phy, SuperSpeed (SSTX+/SSTX-/SSRX+/SSRX-) data lines.
>> +  - "usb2" phy, USB 2.0 (D+/D-) data lines.
>> +
>> +- extcon: Must contains an extcon entry which detects USB VBUS pin.
>> +  See ../extcon/extcon-usb-gpio.txt for details.
> 
> Use the usb-connector binding for new bindings.
> 

already taken care in V4 series of this patch.

Thanks,
Nagarjuna
>> +
>> +Example:
>> +--------
>> +	pmc: pmc@7000e400 {
>> +		compatible = "nvidia,tegra210-pmc";
>> +		reg = <0x0 0x7000e400 0x0 0x400>;
>> +		clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
>> +		clock-names = "pclk", "clk32k_in";
>> +
>> +		powergates {
>> +			pd_xusbss: xusba {
>> +				clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>;
>> +				resets = <&tegra_car TEGRA210_CLK_XUSB_SS>;
>> +				#power-domain-cells = <0>;
>> +			};
>> +
>> +			pd_xusbdev: xusbb {
>> +				clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>;
>> +				resets = <&tegra_car 95>;
>> +				#power-domain-cells = <0>;
>> +			};
>> +		};
>> +	};
>> +
>> +	xudc@700d0000 {
>> +		compatible = "nvidia,tegra210-xudc";
>> +		reg = <0x0 0x700d0000 0x0 0x8000>,
>> +			<0x0 0x700d8000 0x0 0x1000>,
>> +			<0x0 0x700d9000 0x0 0x1000>;
>> +
>> +		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> +		clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>,
>> +			<&tegra_car TEGRA210_CLK_XUSB_SS>,
>> +			<&tegra_car TEGRA210_CLK_XUSB_SSP_SRC>,
>> +			<&tegra_car TEGRA210_CLK_XUSB_HS_SRC>,
>> +			<&tegra_car TEGRA210_CLK_XUSB_FS_SRC>;
>> +		clock-names = "dev", "ss", "ss_src",
>> +			      "hs_src", "fs_src";
>> +
>> +		power-domains = <&pd_xusbdev>, <&pd_xusbss>;
>> +		power-domain-names = "dev", "ss";
>> +
>> +		nvidia,xusb-padctl = <&padctl>;
>> +
>> +		phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>;
>> +		phy-names = "usb2;
>> +
>> +		avddio-usb-supply = <&vdd_pex_1v05>;
>> +		hvdd-usb-supply = <&vdd_3v3_sys>;
>> +
>> +		extcon = <&extcon_usb>;
>> +	};
>> +
>> +	extcon_usb: extcon_vbus {
>> +		compatible = "linux,extcon-usb-gpio";
>> +		vbus-gpio = <&gpio TEGRA_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
>> +	};
>> +
>> -- 
>> 2.7.4
>>



[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux