Re: [PATCH V13 3/5] i2c: tegra: Add DMA support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



06.02.2019 19:07, Dmitry Osipenko пишет:
> 06.02.2019 18:55, Sowjanya Komatineni пишет:
>>
>>
>>>> Two ";;" at the end.
>>>>
>>>>
>>>>
>>>> Good news: DVC I2C works now and tps6586x probes fine! :) Bad news: 
>>>> atmel-touch still has same problems as in V12 :(
>>>>
>>>> DMA-only V13: http://dpaste.com/0XJ1Z8G.txt
>>>
>>> Strangely, there are many transactions to touch and all of them are good except DMA timeout only when reading T44 and T5 atmel_mxt_ts 0-004c: Failed to read T44 and T5 (-110)
>>
>> [    0.923138] tegra-i2c 7000c000.i2c: starting DMA for length: 16
>> [    0.923148] tegra-i2c 7000c000.i2c: unmasked irq: 0c
>> [    0.923337] tegra-i2c 7000c000.i2c: transfer complete: 10 0 0
>> [    0.923347] tegra-i2c 7000c000.i2c: starting DMA for length: 12
>> [    0.923355] tegra-i2c 7000c000.i2c: unmasked irq: 0c
>> [    0.935048] tegra-i2c 7000d000.i2c: starting DMA for length: 16
>> [    0.935058] tegra-i2c 7000d000.i2c: unmasked irq: 0c
>> [    1.028750] tegra-i2c 7000c000.i2c: DMA transfer timeout
>> [    1.028816] atmel_mxt_ts 0-004c: __mxt_read_reg: i2c transfer failed (-110)
>>
>> Looking into timestamps and transactions, DMA timeouts after start of DMA for I2C1 to touch during this transaction.
>> While it is waiting for I2C1 DMA transfer, lots of DVC transactions happened thru DMA which are successful
>>
>> What is the I2C1 speed?
> 
> 400KHz
> 
>> Also incase if device is running slow for some reason, probably timeout was not enough as this patch series changes timeout with base 100mS + msg transfer time based on transfer size.
>> Can you give quick try with increased timeout incase if device is running slow?
>>
> 
> Tried to increase the timeout to 1 second, doesn't help.
> 
> What helped again is the I2C HW resetting after each transfer. Likely that means that HW isn't programmed correctly, please carefully check every bit.
> 
> DMA-only + I2C HW reset: http://dpaste.com/26AQXFM.txt

Seems I found what's the problem. Here is the fix, please include it to v14 if it is correct.

diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c
index a9391c3646b6..5ad54da70304 100644
--- a/drivers/i2c/busses/i2c-tegra.c
+++ b/drivers/i2c/busses/i2c-tegra.c
@@ -912,7 +912,7 @@ static irqreturn_t tegra_i2c_isr(int irq, void *dev_id)
 static void tegra_i2c_config_fifo_trig(struct tegra_i2c_dev *i2c_dev,
                                       size_t len)
 {
-       u32 val, reg;
+       u32 val = 0, reg;
        u8 dma_burst = 0;
        struct dma_slave_config slv_config = {0};
        struct dma_chan *chan;
@@ -922,7 +922,6 @@ static void tegra_i2c_config_fifo_trig(struct tegra_i2c_dev *i2c_dev,
                reg = I2C_MST_FIFO_CONTROL;
        else
                reg = I2C_FIFO_CONTROL;
-       val = i2c_readl(i2c_dev, reg);
 
        if (i2c_dev->is_curr_dma_xfer) {
                if (len & 0xF)



[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux