On 12/13/18 7:41 PM, Jon Hunter wrote:
On 13/12/2018 09:34, Joseph Lo wrote:
The DFLL hardware supports two modes (I2C and PWM) for voltage control
when requesting a frequency. In this patch, we introduce PWM mode support.
To support that, we re-organize the LUT for unifying the table for both
cases of I2C and PWM mode. And generate that based on regulator info.
For the PWM-based regulator, we get this info from DT. And do the same as
the case of I2C LUT, which can help to map the PMIC voltage ID and voltages
that the regulator supported.
The other parts are the support code for initializing the DFLL hardware
to support PWM mode. Also, the register debugfs file is slightly
reworked to only show the i2c registers when I2C mode is in use.
Based on the work of Peter De Schrijver <pdeschrijver@xxxxxxxxxx>.
Signed-off-by: Joseph Lo <josephl@xxxxxxxxxx>
---
*V2:
- move reg_init_uV to be with the PWM related variables
- fix the variable type to 'unsigned long' if it needs to catch the
return value from 'dev_pm_opp_get_voltage'
- update to use lut_uv table for LUT look up. This makes the generic
lut_uv table to work with both PWM and I2C mode.
---
drivers/clk/tegra/clk-dfll.c | 435 +++++++++++++++++++++++++++++------
1 file changed, 369 insertions(+), 66 deletions(-)
snip.
@@ -594,24 +750,41 @@ static void dfll_init_out_if(struct tegra_dfll *td)
{
u32 val;
- td->lut_min = 0;
- td->lut_max = td->i2c_lut_size - 1;
- td->lut_safe = td->lut_min + 1;
+ td->lut_min = td->lut_bottom;
+ td->lut_max = td->lut_size - 1;
+ td->lut_safe = td->lut_min + (td->lut_min < td->lut_max ? 1 : 0);
+
+ /* clear DFLL_OUTPUT_CFG before setting new value */
+ dfll_writel(td, 0, DFLL_OUTPUT_CFG);
+ dfll_wmb(td);
- dfll_i2c_writel(td, 0, DFLL_OUTPUT_CFG);
val = (td->lut_safe << DFLL_OUTPUT_CFG_SAFE_SHIFT) |
- (td->lut_max << DFLL_OUTPUT_CFG_MAX_SHIFT) |
- (td->lut_min << DFLL_OUTPUT_CFG_MIN_SHIFT);
- dfll_i2c_writel(td, val, DFLL_OUTPUT_CFG);
- dfll_i2c_wmb(td);
+ (td->lut_max << DFLL_OUTPUT_CFG_MAX_SHIFT) |
+ (td->lut_min << DFLL_OUTPUT_CFG_MIN_SHIFT);
+ dfll_writel(td, val, DFLL_OUTPUT_CFG);
+ dfll_wmb(td);
dfll_writel(td, 0, DFLL_OUTPUT_FORCE);
dfll_i2c_writel(td, 0, DFLL_INTR_EN);
dfll_i2c_writel(td, DFLL_INTR_MAX_MASK | DFLL_INTR_MIN_MASK,
DFLL_INTR_STS);
- dfll_load_i2c_lut(td);
- dfll_init_i2c_if(td);
+ if (td->pmu_if == TEGRA_DFLL_PMU_PWM) {
+ int vinit = td->reg_init_uV;
This should be u32.
+ int vstep = td->soc->alignment.step_uv;
+ int vmin = td->lut_uv[0];
This should be unsigned long.
+
+ /* set initial voltage */
+ if ((vinit >= vmin) && vstep) {
+ unsigned int vsel;
+
+ vsel = DIV_ROUND_UP((vinit - vmin), vstep);
+ dfll_force_output(td, vsel);
+ }
+ } else {
+ dfll_load_i2c_lut(td);
+ dfll_init_i2c_if(td);
+ }
}
/*
@@ -640,8 +813,8 @@ static int find_lut_index_for_rate(struct tegra_dfll *td, unsigned long rate)
uv = dev_pm_opp_get_voltage(opp);
dev_pm_opp_put(opp);
- for (i = 0; i < td->i2c_lut_size; i++) {
- if (regulator_list_voltage(td->vdd_reg, td->i2c_lut[i]) == uv)
+ for (i = td->lut_bottom; i < td->lut_size; i++) {
+ if (td->lut_uv[i] >= uv)
I think that we need to fix the type for 'uv' in this function while we
are at it.
Okay, looks like I still have some variable type issue in V2. Will fix
accordingly.
Thanks,
Joseph
Cheers
Jon
